Ford 6.0L Power Stroke Diesel :: 2007 F350 - Power Loss After 10 Miles And Dies But Will Restart?
I have a 2007 F350 6.0 Diesel. Truck starts and runs great for about 10 miles and then loses power and slows down til it dies, it does this without any kind of warning and does not rattle or anything. If i let it sit for about 15 min it will start right up and drive fine for another 10 miles or so and do the same thing.
It did the same thing in December but would not restart at all and the ficm was the cause at that time so i went ahead and replaced the ficm just to eliminate it. I also replaced the fuel pump and the ipr and icp valves are good. The only engine code has to do with the fuel level sensor and that has been on for a year. The egr was recently replaced, the hpop is putting out the psi that it is supposed to and there are not any internal air leaks.
Ford 6.0L Power Stroke Diesel :: 2004 F350 No Longer Accelerate / Completely Dies Going Uphill / Will Not Restart
I have a late model 2004 F-350 6.0 powerstroke. 182K miles. Auto Transmission
What happened. Condensed version
Left house, drove out to highway, got on highway. Everything feels normal.
About 1 mile of going 70mph, I notice I can no longer accelerate. after 1/2 mile, I begin loosing speed, and engine will not rev past 1000 rpm. I eventually pull over (another mile), put in neutral and will not rev past 1000. put in drive and start to idle to highway exit. it gets about another .5 mile and begin going up a hill when it completely dies. Will not restart.
No prior issues with the truck. Full tank of fuel.
What I have tested so far. Ficm 48.5 volts cranking. Icp .225V KOEO, .875V Cranking. LPOP is registering pressure on the dash. No Fault codes.
I have gotten it to start twice now, one time it allowed me to rev to 750 rpm, where i used 4 low to make it onto a trailer. second time would not rev at all. idling at 250-300 rpm.
That same night as it died, I drained the transmission pan/ TP filter and filled with 8.5 Quarts of Mercon LV. This is the first time I have done this since purchasing @ 161K miles. Everything seemed normal, no leaks present.
Also my buddy showed me how to enter the dash test mode and we cycled through these. Not sure if this is relevant.
So, What do I test next? I don't think its HPOP issue since the ICP is reading .875 volts at crank. I did unplug the ICP and it still would not start. I don't think its the injector side of the ficm because they buzz as normal with koeo, but this is a possibility as I don't have equipment to test. Egr valve is clean for age of truck.
Would it be possible that the Mercon LV knocked crud loose in the transmission causing it to fail/seize? would siezed tranny cause the engine to behave in this manner?
Fuel bowl on top of the engine was full of fuel. I have not pressure tested it yet as I can hear the pump running during key on.
could i have a bad crank or cam sensor?
Multi-injector failure?
Bad Icp with HPO failure?
Ford 6.0L Power Stroke Diesel :: 2005 Truck Dies Under Load?
So pulling my trailer and 4x4 and the truck dies without any other symptoms. No check engine light all other electrical remains working. This happened 6 times this trip always while pulling a grade but only after the truck has been running for a few hours. Each time, no warning and once the truck has set for 5 to 10 minutes it start up like normal. The longer i let it set the longer I can run before it does it again. ICP is 550ish at idle, 200ish while cranking. Check the FICM before the trip and it was at 47.5 to 48.5v key on engine off and running. STC, stand pipes, dummy plugs, ball cups have all been done.
View 10 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Starts And Dies Numerous Times
I've got an '05 F-250 starts and dies numerous times, have to rev throttle to keep running then it stays running. I've replaced FICM, PCM, Eng. harness, IPR, CMP, what else is there to do?
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - Lag Off Idle For About A Second Every Once In A While
Well, after getting the bed back on my '05 F350, I have been driving it on the road for a few days, but now I have a new problem.
Every once in awhile I get lag off idle for about a second, then the turbo spools and everything is fine. Other times, I step on the accelerator a bit from a stop, and the truck acts like its going to die for a moment, a puff of black smoke, and then the turbo spools and all is back to normal. It a combination of these two problems happens about 3-5 times out of 50 stops a day.
I have a scanguage and everything looks normal and I never get any codes when I check.
Ford 6.0L Power Stroke Diesel :: 2005 F350 DRW FX4 - How To Improve MPG
I have a bone stock 2005 F350 DRW FX4 6.0 Diesel. I've been averaging 10.5 to 14 MPG city. Haven't really done any hiway driving yet.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - Won't Start?
2005 F 350 6.0
124000 miles. Drove the truck on a long road trip Saturday ran great. Didn't touch it Sunday. Went out Monday morning and it wouldn't start I noticed the fuel gauge said empty and the low fuel light was on. I knew there was plenty of diesel still in the tank but I still went and bought 5 gal and dumped in it fuel gauge then read over half full but still won't start. A buddy who's a mechanic swung by sprayed starter fluid in it fired right up then died he said I need a new fuel pump. I have been reading the forums. I just want to make sure is he right?
Ford 6.0L Power Stroke Diesel :: 2005 F350 4WD Will Not Shift On The Fly
I have 2005 f350 will not shift on the fly. With a vacuum pump it will hold vacuum at both hubs but will not lock up. The seals should be good.
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 Won't Turn Over With The Key
My 05 F350 6.0 won't turn over with the key, everything comes on like normal but won't turn over. Starts fine with factory remote start. What to check?
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - Hard / No Start - Low Power
Don't know where to start so I'll ramble!
2005 f350 with the 6.0. Crew Cab, 8' box, 4x4 with DRW. I use it only take the boat to the launch 5 minutes away once in a while and to pull car trailers every other week. Majority of driving is on the highway and average trip is about 300 miles. Low power and now no start.
No codes. I do have a scan Gauge and can provide data.
Was running this week, but has had a lack of power for some time. I had put 2 new injectors in last summer. Also updated dummy and stand pipes. Blue spring. Also new IPR at the time.
Ficm board was replaced in March.
New injector harness last year. New Glow plug harness last year.
Coolant level is fine and none being lost.
CAC hoses appear fine, no cracks.
No boost. But newer MAP sensor, hose not cracked or plugged and nipple on intake is clear. Put the MAP sensor last year and it didn't make a difference.
Turbo was rebuilt 2 years ago.
IPR has to hit close to 80 before boost hits 12-15. But it takes a while to get there.
Now won't start.
Yesterday am it was about 30 farenheit and no start. Last year would start no problem.
Batteries are fine. tested.
Engine fires within 3 seconds, but doesn't want to run.
ICP is above 500. climbs as I turn over.
Fires only in first few seconds and then nothing while I keep cranking it. it is cranking fast enough though.
Now...I see IPR will hit 84.7% and then 14.8%. Not good!
When running it sits in between.
FICm voltage is 48.5 key one and 47.5 when cranking.
Wondering if possibly IPR screen is plugged? Or would CKS or CPS cause issues? I recall reading about pulling one of them and cleaning rust off of it? Also...should mention, no EGR reading on scan gauge..never was either. I had checked and cleaned egr valve before. it was clean when I pulled it and not sticking.
Intake had been cleaned 2years ago. Also, on occasion, while pulling up hill, I would get power! Black smoke and it would race up a hill like it's supposed. Then it would go back to no power.
Also...if I pull the MAP hose from the intake nipple, should I feel suction from the intake? There doesn't appear to be any air coming or going from the nipple.
Ford 6.0L Power Stroke Diesel :: 2005 F350 - Lost Power And Won't Start
I have 2005 f350 with 365000 km on it I have it for one year and don't have a problem till last week. I was pulling van on dolly uphill and sadden lost pover, so I stopped and check oil leaks ,transmission .... But everything looks ok in couple minutes start engine and go home (10 km). Change fuel filters trans filter, looked good for 50km and star losing power again and doesn't want start. So I skan and its show me next numbers.
Key on engine off
Ipr-15%
Icp-0psi
Icp-.26v
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine crank
Ipr-85%
Ficm main power-48.0
Ficm logistics-12.5
Icp- 625psi
Icp-.77v-1v
So what I have to do?
Ford 6.0L Power Stroke Diesel :: 2005 F350 - No Power To Move
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didn't have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines, harness, pump, sending unit , tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to the garage had them swap it out and now they said come get the truck they won't work on it anymore that now it needs 3 injectors and they won't touch it with aftermarket fuel system on it. So i go to drive it home and it starts but runs rough and u can hold it to the floor and it won't budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now.
Ford 6.0L Power Stroke Diesel :: 2005 F350 - Hesitates / Low Power Driving / Idle
I have a 2005 F-350 Lariat, FX4, CrewCab, with an 8ft Bed if any of that matters. Currently sitting at 191,000 miles and 4,500 Engine Hours I just started running into some issues that I cannot figure out. To start with here is a list of all the mods and prior maintenance that I've done to my truck over that last 6+ years that I've owned it.
I purchased the truck in 2010 and had no issues whatsoever for the first 3 years.....then it all started. While pulling a camper home from vacation "still bone stock" the truck overheated and by the time I realized it it was to late. I ended up blowing a head gasket cracking a head and blowing a hole in my coolant reservoir from the heat & compression of the engine in the coolant system. So to the shop it went.
All of this was done at the same time at just under 4,000 engine hours:
1) Both heads were sent out to be pressure tested "which is where the crack was found", so 1 replacement head and the other trued up and tested by the machine shop
2) All 8 injectors replaced with Airtex/Wells New/Reman
3) ARP Head Studs
4) BPD EGR Cooler
5) New Stock Coolant Reservoir
6) New Stock Oil Cooler
7) Motorcraft Coolant & Oil/Oil Filter Change
8) New Serpentine Belt
After getting the truck back I installed some upgrades that I had wanted but didn't want to do until I had head studs. 4" Turbo back Diamond Eye Performance exhaust, Bully Dog GT Tuner with an EGT Pyro, coolant changed to Caterpillar ELC, Sinister Diesel coolant filtration system, new Optima batteries "I hated them",
Forward a year with no problems I had a crank but no start. I ended up having a bad IPR. A buddy rebuilt the turbo since I had it out and it was leaking. He apparently did something wrong because it took its own life sometime after. So a brand new stock Garrett Turbo with a Wicked Wheel 2 & I changed the IPR "don't remember the brand." Also replaced the factory paper air filter with a cleanable one from AFE that fits in the factory cold air intake.
Little more time and I started to have some overheating issues again, luckily the Bully Dog was monitoring and I had alerts set up so I caught it way before it caused any serious damage. Turned out the fan clutch wasn't working. So I replaced the Water Pump with one from dieselsite.com that has a steel impeller, also replaced the computer controlled fan clutch with a 7.3L mechanical fan clutch and an adapter from BPD.
After that the batteries I hated were replaced. I installed Oddssey Extreme 950CCA ones, a new 185A alternator from FICMRepair.com as well as the complete battery wiring interconnect kit. Did the blue spring upgrade. Replaced my FICM with the BPD 6 phase at 54V setting. Also I changed my starter to an 6.4L Ultima one from O'Reily Auto to bring me up from that slow crank of the 6.0L at about 150RPM to the 225RPM of the 6.4L.
So now on to the current issue. This has happened in the last month and may be related to the issue. I had some small coolant leaks and wanted them fixed. Pressure tested the system & found the radiator and timing cover gasket leaking. I installed a new stock radiator and lower radiator hose. Had the shop do the gasket and a serpentine belt due to cleaners being all over it. During replacement of the timing cover gasket my mechanic found that the LPOP gears had some damage as if something had be in there at one time. Not sever damage just minor. LPOP replaced with brand new one from Ford.
After I got the truck back it was fine for 2 weeks, no leaks or any problems whatsoever. Then I noticed a hesitation as I was leaving work at idle. You could see the RPM's moving up and down by about 50 as it sat there at idle. It got really bad and eventually stalled on me. It fired right back up and ran fine after. I was thinking water in the fuel or just maybe old fuel because it was kinda old and I was at 1/4 of a tank. I went and filled up and it ran great all the way home. Day or so later same thing. At idle you can see the RPM fluctuating and while driving it feels like it has no power at times then it goes away and runs fine. So I changed both fuel filter with Motorcraft ones and put in a new oil filter. It is the Wix brand but I've be running it for years with no issues, one was also in it way before this issues started. The oil has about 2,000 miles on it currently. I verified fuel pressure at idle to be at 70PSI. I tried unplugging the ICP at idle with no change in the hesitation. So I plugged in my SG2 and started to see if I could see anything out of the ordinary.
OAT - 60 Degrees F
KOEO Engine Cold - FMP - 54.5V, ICV - 0.25V, ICP - 0, IPR - 14.9
KOER Engine Warm - FMP - 54.5V, ICV - 0.82V, ICP - 576, IPR - 23.5
Cruise at 40MPH - FMP - 54.5V, ICV - 1.14V, ICP - 965, IPR - 32.9
Cruise at 50MPH - FMP - 54.5V, ICV - 1.42V, ICP - 1,190, IPR - 38.0
Cruise at 60MPH - FMP - 54.5V, ICV - 1.27V, ICP - 1,143, IPR - 37.2
While driving this issue comes and goes very randomly. The only parameter I notice changing alot is the IPR. It jumps around a lot and sometimes it will go to 85. I know that this isn't a good thing so I am going to change the IPR later today or tomorrow. I already had a brand new Motorcraft one to put in, plus at the very least I want to look at the screen. I had read somewhere that there could be air in the oil system and that if you run at a high RPM it can remove this air. I never seen any bubbles or anything on the dipstick. My brother ran the truck for me at 3,000RPM for 5 minutes. No hesitation during the test but he didn't have the SG2 plugged in so I don't know the parameters during the test. I thought that it worked but then it came back after a few miles of driving. The above parameters are from this mornings drive home from work.
Ford 6.0L Power Stroke Diesel :: 2005 F350 Running Rough - No Power To Move
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didnt have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines,harness,pump,sending unit ,tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to garage had them swap it out and now they said come get the truck they wont work on it anymore that now it needs 3 injectors and they wont touch it with aftermarket fuel system on it. So I go to drive it home and it starts but runs rough and u can hold it to the floor and it wont budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now .
Ford 6.7L Power Stroke Diesel :: 2014 F350 - Axle Gear Change?
I am thinking about changing the Gear Ratio in my 2014 Platinum F350.
History: I traded in my 2011 F350 DRW with 17" wheels and 3:73 gears to get my 2014 F350 SRW 20" Wheels with the 3.55 gears. I pull a 15,000 boat and trailer. The Drw pulled the boat and trailer with no issues. I sold my Northern Lite Truck Camper. I thought I didn't need the Drw any more. First time I hooked up to the boat I felt the difference in between the trucks in the acceleration and fuel economy. Old truck would get 11.5 MPG new truck gets barely 9 MPG going down hill with a tailwind. Over all the new truck is a little slower off the line but when hooked up to the boat it is a dog with the 20" tires.
So the question to you all is; gear change to 4.10? Swapping to this ratio with 20" tires will produce the similar RPM's and possible improve the fuel economy. I get around 18 empty now on trips empty. Around 16 commuting 25 miles to work.
Ford 6.7L Power Stroke Diesel :: 2012 F350 - Trans Would Not Shift Into 6th Gear
My Father In-law has a 2012 f-350 Dually with 4K miles. He tows a 9K lb camper and until our last trip the truck ram flawlessly. On our return from Myrtle Beach to central NC we were on a freeway traveling at 63 MPH and his tranny would not shift into 6th gear. Tow haul was on. There was some headwind (10MPH) but no large grades or any reason we can think of not to allow an up shift. His display did show a countdown to empty of the exhaust fluid 450 miles to empty.
He took the truck in for service and no codes were found. Dealer did not find any TSB's addressing the tranny issues. Is the sixth gear up shift in tow haul set very conservative? Does it hold 5th unless the load is below a certain value? Other trips we have been on have been mountain towing so 6th gear shift would have been on down hill or level sections. Dealer wants us to bring it to them when it won't up shift next time but dealer is not along a freeway.
Ford 6.0L Power Stroke Diesel :: 2005 F350 - Starts When Cold But Not When Hot
I just bought an 05 F350 and it starts fine when cold but after I drive it a while will not start even after sitting for up to an hour (overnight cold start fires right up). I replaced 1 battery and alternator and it started up right after install but after driving for a while still have the problem - cranks fine but will not start.
Buddy of mine has the same truck (just a 250) and had this same problem recently and had to replace the High Pressure Oil Pump, which was super expensive! This is my first diesel truck and it runs like a champ (once it starts!)
Ford 6.0L Power Stroke Diesel :: 2005 F350 - Compressor Damaged?
I recently picked up a 2005 F350 6.0. I got it cheap with a plugged oil cooler, and went in planning to do studs, gaskets, and all the Ford updates just to have it out of the way. When taking it apart, I quickly noticed that the compressor was damaged. Looks to me like some foreign object(s) entered the turbo, would bounce off the wheel, impact the cover, and repeat.
Engine seemed to run great. Turbo spooled quickly and while I wasn't paying close attention, I'd glance when accelerating and it'd be in the neighborhood of 27 PSI. Engine cranks evenly and starts well, so there's no obvious engine damage. I'll inspect the bores closely with the heads off.
So my main question: Assuming no damage elsewhere, Do I need just a wheel? There is some pitting and high spots on the cover, but could it be carefully worked down with the cover removed? Do I just need to get a wheel and a cover? Or just a whole new turbo? Looking for a budget-friendly option to remedy this properly.
Ford 6.0L Power Stroke Diesel :: 2005 F350 - No Start / Cut Off While Driving
My friend has an 05 6.0. He's having a no start issue. He was driving and it cut off, he couldn't remember if it cut off quick or sputtered. I hooked up my AE and jumper cables and stated looking. Cranking the icp would only build up to 190ish. I unplugged the icp sensor and AE was reading 1538ish??, I guess that was a default value. The ipr reading immediately went up to 85% but still doesn't fire. Also while cranking there wasn't any white smoke at all from the exhaust. A few years ago he broke down and Ford put in the updated snap to connect fitting. He said they also replaced the dummy plugs but he didn't mention stand pipes so... I'm not where the truck is so if there's any questions it might take a few.
View 9 Replies