Ford 6.0L Power Stroke Diesel :: 2006 - Hesitates Intermittently - Stumble At Idle?
I have a 2006 F-250 4x4 with no cat, and no egr but the valve is still connected. It has about 146,000 miles. Just recently when warm, it has a slight miss every once and a while when stopped and in gear. Just a slight drop in RPM then recovery. Its mainly used on the highway and 99% of the time I set the cruise and its smooth as silk. Every once and a while I feel it stumble once or twice, recover and it is fine for the next 80 miles with no issue. It started as once every few trips but now It seems to be happening at least once every other. I use Motorcraft filters (maybe 6K on the fuel filters) and rotella oil. My scangaugeII shows no codes and no Injector pressure issue (1200-1400 at 75 mph depending on grade) and the FICM voltage stays between 48.5v and 49.0V. What should I check?
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - Hesitates / Low Power Driving / Idle
I have a 2005 F-350 Lariat, FX4, CrewCab, with an 8ft Bed if any of that matters. Currently sitting at 191,000 miles and 4,500 Engine Hours I just started running into some issues that I cannot figure out. To start with here is a list of all the mods and prior maintenance that I've done to my truck over that last 6+ years that I've owned it.
I purchased the truck in 2010 and had no issues whatsoever for the first 3 years.....then it all started. While pulling a camper home from vacation "still bone stock" the truck overheated and by the time I realized it it was to late. I ended up blowing a head gasket cracking a head and blowing a hole in my coolant reservoir from the heat & compression of the engine in the coolant system. So to the shop it went.
All of this was done at the same time at just under 4,000 engine hours:
1) Both heads were sent out to be pressure tested "which is where the crack was found", so 1 replacement head and the other trued up and tested by the machine shop
2) All 8 injectors replaced with Airtex/Wells New/Reman
3) ARP Head Studs
4) BPD EGR Cooler
5) New Stock Coolant Reservoir
6) New Stock Oil Cooler
7) Motorcraft Coolant & Oil/Oil Filter Change
8) New Serpentine Belt
After getting the truck back I installed some upgrades that I had wanted but didn't want to do until I had head studs. 4" Turbo back Diamond Eye Performance exhaust, Bully Dog GT Tuner with an EGT Pyro, coolant changed to Caterpillar ELC, Sinister Diesel coolant filtration system, new Optima batteries "I hated them",
Forward a year with no problems I had a crank but no start. I ended up having a bad IPR. A buddy rebuilt the turbo since I had it out and it was leaking. He apparently did something wrong because it took its own life sometime after. So a brand new stock Garrett Turbo with a Wicked Wheel 2 & I changed the IPR "don't remember the brand." Also replaced the factory paper air filter with a cleanable one from AFE that fits in the factory cold air intake.
Little more time and I started to have some overheating issues again, luckily the Bully Dog was monitoring and I had alerts set up so I caught it way before it caused any serious damage. Turned out the fan clutch wasn't working. So I replaced the Water Pump with one from dieselsite.com that has a steel impeller, also replaced the computer controlled fan clutch with a 7.3L mechanical fan clutch and an adapter from BPD.
After that the batteries I hated were replaced. I installed Oddssey Extreme 950CCA ones, a new 185A alternator from FICMRepair.com as well as the complete battery wiring interconnect kit. Did the blue spring upgrade. Replaced my FICM with the BPD 6 phase at 54V setting. Also I changed my starter to an 6.4L Ultima one from O'Reily Auto to bring me up from that slow crank of the 6.0L at about 150RPM to the 225RPM of the 6.4L.
So now on to the current issue. This has happened in the last month and may be related to the issue. I had some small coolant leaks and wanted them fixed. Pressure tested the system & found the radiator and timing cover gasket leaking. I installed a new stock radiator and lower radiator hose. Had the shop do the gasket and a serpentine belt due to cleaners being all over it. During replacement of the timing cover gasket my mechanic found that the LPOP gears had some damage as if something had be in there at one time. Not sever damage just minor. LPOP replaced with brand new one from Ford.
After I got the truck back it was fine for 2 weeks, no leaks or any problems whatsoever. Then I noticed a hesitation as I was leaving work at idle. You could see the RPM's moving up and down by about 50 as it sat there at idle. It got really bad and eventually stalled on me. It fired right back up and ran fine after. I was thinking water in the fuel or just maybe old fuel because it was kinda old and I was at 1/4 of a tank. I went and filled up and it ran great all the way home. Day or so later same thing. At idle you can see the RPM fluctuating and while driving it feels like it has no power at times then it goes away and runs fine. So I changed both fuel filter with Motorcraft ones and put in a new oil filter. It is the Wix brand but I've be running it for years with no issues, one was also in it way before this issues started. The oil has about 2,000 miles on it currently. I verified fuel pressure at idle to be at 70PSI. I tried unplugging the ICP at idle with no change in the hesitation. So I plugged in my SG2 and started to see if I could see anything out of the ordinary.
OAT - 60 Degrees F
KOEO Engine Cold - FMP - 54.5V, ICV - 0.25V, ICP - 0, IPR - 14.9
KOER Engine Warm - FMP - 54.5V, ICV - 0.82V, ICP - 576, IPR - 23.5
Cruise at 40MPH - FMP - 54.5V, ICV - 1.14V, ICP - 965, IPR - 32.9
Cruise at 50MPH - FMP - 54.5V, ICV - 1.42V, ICP - 1,190, IPR - 38.0
Cruise at 60MPH - FMP - 54.5V, ICV - 1.27V, ICP - 1,143, IPR - 37.2
While driving this issue comes and goes very randomly. The only parameter I notice changing alot is the IPR. It jumps around a lot and sometimes it will go to 85. I know that this isn't a good thing so I am going to change the IPR later today or tomorrow. I already had a brand new Motorcraft one to put in, plus at the very least I want to look at the screen. I had read somewhere that there could be air in the oil system and that if you run at a high RPM it can remove this air. I never seen any bubbles or anything on the dipstick. My brother ran the truck for me at 3,000RPM for 5 minutes. No hesitation during the test but he didn't have the SG2 plugged in so I don't know the parameters during the test. I thought that it worked but then it came back after a few miles of driving. The above parameters are from this mornings drive home from work.
Ford 6.0L Power Stroke Diesel :: 2004 F350 - Intermittent Loss Of Power / Stall Or Stumble When Engine Is Cold
I just bought a 2004 F350 6.0 cclb 6 speed with 260k on it. The previous owner seemed to have taken good care of the truck. It is basically stock with the exception of the blue spring mod, and a sinister diesel coolant filter. Anyways, I brought the truck home and it ran great. Now I have an issue that needs to be addressed.
The issue: I am experiencing a intermittent loss of power, stall, or stumble when engine is cold. After sitting all night the truck will start fine and idle fine. But when I try to accelerate and bring engine RPM up the engine will stumble and lose all throttle response, when this happens the WTS and WIF light flash. Sometimes it just stumbles, sometimes the truck will actually die and then restart. The issue seems to go away after the engine has reached operating temp.
I did some research on the issue and it seems there is actually a TSB out from ford for this issue. It explains that some 2003-2004 6.0's might have wiring harness chaffing issues. This is what the issue I am having seems like to me (shorting harness). I looked up codes on the truck and there is an active code (#8 glow plug circuit fault). I did a short visual inspection of harness and didn't see anything out of the ordinary. But i wonder if it would be worth changing both sides of the glow plug harness?
Ford 6.0L Power Stroke Diesel :: Stuttering On Acceleration / Fuel PSI At Idle Barely Move
I fear my truck may be stuttering on acceleration.
I hooked up a fuel pressure gauge tonight and the fuel PSI at idle and under acceleration... barely moved. Stayed between 60-62PSI.
I'm thinking this isn't normal... shouldn't the PSI be reduced especially when I accelerate hard ?
I'm thinking the "delivery" fuel line... perhaps there is a bottle neck somewhere which is causing constant PSI at the fuel housing ?
Ford 6.0L Power Stroke Diesel :: Surges / Buck At Acceleration - Gallop / Miss / Stall At Idle?
I've seen the gods of the diesel engine do some amazing things on these forums, so after a year of pulling my hair out, I've signed up to try this myself.
This time least year,I bought a 2004.5 6.0L F-250 with 196k on it to haul around the state for my new business. At this time, I knew nothing about diesel engines AT ALL WHATSOEVER, but I've never been afraid to tackle anything and mechanics are not totally foreign to me. Not to mention, I was hoping everything might just go peach-ily for at least a couple years. (for what it's worth, My dad and his family are mostly shade tree mechanics and I'm a power plant operator so mechanical concepts are not totally foreign to me, just never had a diesel before)
To begin, I purchased the truck and everything was fine for about 2 weeks. Then abruptly one morning I noticed a couple of hefty surges on the way to work. Then, on the way home I thought all was well until about half way home, it did it again! as I was pulling up, it galloped once I pulled my foot off the pedal. like ba-DA-DA-DA-da-da-da-da-da-da-DA-DA-DA-DA-DA-da-da-__ and then STALL! Shaking with concern over potentially an awful purchase, I turned the truck back on only to find... that it's fine?!?? No problems for the next two days and then it happened again. then good for a week, then again. then good for 2 weeks, then again. so then I bought auto enginuity and an edge insight to do some troubleshooting. Let that sink in as I explain it's history a bit.
-All but one injector is ford remanufactured the other is stock (was never told which one)
-replaced head gasket with another OEM
-ARP Head Studs
-EGR delete
-HPOP AND STC fitting both replaced
-FICM replaced
-Oil cooler replaced 50k ago
-ICP and pig tail replaced right before my purchase
- Has been through roughly a handful of ICP's since I've had it (I'll explain)
-I've cleaned the EBP tube a lot and updated it to the newer ford sensor with the flare fitting
-I use Rotella T6 5W40 and CAT ELC-1 Coolant.
-Deltas are under 10 at normal driving
-I typically drive under 2200 rpm until warm then like a banshee at operating temps.
Now one year later, its not fixed, but I feel like I'm close.
The DTC's I have seen are ICP sensor circuit intermittent (I think po2884) and Power Blance contribution failure from cylinders #2 #7 and #8 but never at the same time.
Every time I replace the ICP, it will be problem free for about 6 weeks and then it will return full force (surging and galloping when warm about 50% of the time)
During a possession I see the following:
*Cylinder power contribution test yields no issues at idle or when cold. when "possessed", the whole baseline across all cylinders goes up and all cylinders dip and return at random. none singled out
*ICP voltage fluctuating from ~.6v to 1v (.24 @koeo) *Also during a surge*
*ICP PSI dancing up and down ~600 to 900psi (0.0 @koeo and ~500 at normal warm idle) *Also during a surge*
*IPR% bumps up and down ~25% to 30% (15%@ koeo and 23% at normal warm idle) *Also during a surge*
*FICM Voltage anywhere between 47.5v and 49v
*EBP is normally 15-20 psi
*Boost is 1-7 normal and is not affected by "possession"
These numbers have taken a long time to get since it will only be possessed for about 3-10 seconds at a time and then will disappear for days. The stall has only happened about 5 total times in a year. The surging is much more frequent. I usually get a buck or 2 on any given trip that is longer than a half hour but NOT IMMEDIATELY AFTER AN ICP REPLACEMENT.
On one occasion, I noticed that the ICP PSI actually tanked to about 350 right before the IPR went from 25% to 40% right before a posession. I was driving about 35mph through town at the time.
Here's my thoughts...
- Did that one occasion clue me in to an intermittent HPO system leak causing the truck to briefly over-compensate by spiking the IPR?
- Is my ICP pig tail jobby done incorrectly? If there was a short, wouldn't I see the volts drop to 0? I have another one and will replace to rule it out.
- I have yet to test my fuel pressure, but I figured if it was low, I would have lost injectors by now. (I replace filters probably too often but next empty tank, I'm dropping it and checking the screen and strainers)
I should also mention that I have buzz tested the injectors and I can hear each one clear as day, and that for REALLY long trips, it actually returns to normal. In other words, my window of death is between 30min and 2hrs of driving; invincible after.
Ford 6.0L Power Stroke Diesel :: 2005 - Smoking White Or Gray At Idle But Blowing Black Smoke On Acceleration
Well my problem went from bad to worse. My 05 started running rough at idle, then smoothed out a bit but started smoking on acceleration a little. At this point it felt like it had more power than ever before and even ran smoother running up to 3k RPM before shifting (manual transmission). But now it's smoking so bad, I can't really drive it. It's smoking white or gray at idle but blowing black smoke on acceleration. I had a cylinder 5 contribution code but with the amount of smoke it's hard to believe only one injector is a problem. I pulled the EGR valve and it doesn't look stuck open but I'm going to replace it anyway.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Loses Power / Acceleration - Electrical?
So the 04 is rolling down the road when the cluster gauges ping, the truck loses power/acceleration but the radio never goes out. Have a new alternator and batteries passed a check. It has done it three times. We are 1100 miles from home. OBD and cigarette lighter fuse was blown as well.
View 10 RepliesFord 6.0L Power Stroke Diesel :: 2004 - At Start Up No Acceleration?
First of all, I have 2004 f-350 92K miles with a stock 6.0 - EGR deletes and new oil cooler is the only updates.
Two weeks ago I had an issue pop up. When I tried to start from a dead stop there was no acceleration, it would idle ok but when i pressed on the peddle NOTHING! I called the local diesel guru, he recommended I change the fuel filters. After I did this there was a tremendous improvement in performance.
After a few days of normal driving, I noticed a subtle reduction in throttle response. Today I noticed a slight lag when accelerating which lasted about 3 miles until there is once again no acceleration. It will start normally and idle is a little rough, but will not accelerate even in park the engine is extremely slow to accelerate.
Ford 6.0L Power Stroke Diesel :: Overdrive Stumble / Truck Barely Idling When Come To A Stop
So from what I have gathered online, it is an injector(s) issue. I've only had it happen to me twice at that speed but when I came to a stop afterward, my truck was barely idling.
I'm not sure if my sct programmer is able to show injector codes but it will show gp codes. I guess my question is are failing injectors that intermittent typically? Also, much luck with Rev X clearing that issue up?
Ford 6.0L Power Stroke Diesel :: 2006 - Stumble Always Worst On Final Drive Gear
First... Items I have replaced:
- New EGR valve
- New sensor
- New Fuel filters
- New Oil filter
Problem:
While driving I have a stumble along with a small amount of black smoke at this time ( was white/bluish smoke ) previous. I have dis-connected the batteries to force the computer to relearn the EGR valve. The turbo spools up .. getting about 20 psi @ hard throttle and then about 5 psi after it goes into the final drive gear. Speaking of which ... the stumble is always worst on the final drive gear...
Ford 6.0L Power Stroke Diesel :: Speedometer Not Working Properly With Momentary Engine Stumble?
I've mentioned in earlier posts that my speedometer has been swinging around wildly off and on, and that on two occasions this has been coupled with a momentary engine stumble. This morning on the way to work it was doing it again but this time the engine stumble happened several times as well. I plan to check the speed sensor, but I wonder how this is also causing the engine stumble?
View 3 RepliesFord 6.0L Power Stroke Diesel :: Hesitates To Takeoff?
I have experienced a hesitation on my truck since I purchased it 6 months ago. I get a one to two second hesitation at take off from a stop. I have checked the back pressure tube and the one that goes to the turbo controller no problems. I have a Edge CTS programmer that only shows ... for EBP.
View 13 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 - Hesitates And Won't Go Above Idle Sometimes
I have a 2001 f350 4x4 edge programmer 330k miles. I bought it not running right and thought it would be a easy fix. I'm fairly knowledgeable with the 7.3. Original symptoms where it would run for 5-10 minutes lose power and quit. No restart until it sat for a few hours. P1211 was code, so I figure it's a high pressure oil problem. The truck has a new icp, Ipr, fuel pump, a receipt from dealer where they replaced 1 injectors o ring. I figure the o rings where bad. I replaced all of them.
1 injector was pretty bad the o ring was kinda tore up and disfigured, and 1 had new o rings. Why they would just replace 1 I'll never know. Well the problem still exists, it starts fine sounds good. It will idle 20-30 minutes then get sluggish if I give it any fuel. It's a lot better than before I can floor it and it will rev up and after a few revs it gets better again. If I unplug the icp the idle will go up and down and almost die. Trying to start warm it will just barely run at 4-500 rpm then quit unless I can get it to rev. Once it revs up it seems ok. Does that sound like a hpop problem or am I even on. The right path?
Ford 6.0L Power Stroke Diesel :: 2004 F350 - Severe Shudder While Under Acceleration
I bought my f 350 new from the dealer and have had many of the problems associated with this truck. Now I have a severe shudder while under acceleration when i either let off the gas or increase speed the shudder goes away. My dealer thinks it is injectors but I have little faith. Shudder seems to be rpm consistent and seems to be in the front end. oh yea it idles great and runs great except at that specific range.
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 - Low FICM Voltage Under Acceleration?
Pulled the trigger today and bought a 2004 F350 DRW King Ranch with 200000 miles. Using Forscan Lite on my iPhone, KOEO FICM voltage was right at 48. During start it went up a bit. While out for my highway road test for EOT/ECT differential (never went above 10 degrees).
I noticed that the FICM voltage would drop to the bottom of the Forscan scale (40 volts) when I was accelerating and then go back to 47.5 when I reached my cruising speed. Is this normal?
Batteries are brand new from Ford. I didn't notice the battery voltage. Truck seems to run great to me, but this is my first 6.0. I also got DTC's for all 8 injectors saying Injector Circuit Low.
Ford 6.0L Power Stroke Diesel :: 2007 - Hesitates At Start Up When Cold?
07 6L gave me a fit the other morning. I spent the night in the mountains Saturday night. Sunday morning was -5. With no place to plug in the block heater. When I started it it bucked and hawed and didn't want to run... It keep surging for a while and finally smoothed out after about 3 mins... Is there an additive that will work for this for the times there is no place to plug in? Oil additive or fuel additive?
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2014 - Hesitates From Dead Stop?
I have a 2014 F250 with the 3.55 rear end and 6500 miles and since new it has a hesitation from a dead stop that I cannot determine if it is normal or not. I took it into a dealer that specializes in diesels and they drove it and told me it is normal. Every time I see someone with the 6.7 I ask them if they have the same problem and I get all kinds of explanations from turbo lag to protecting the tranny. The hesitation I feel is when I throttle from a dead stop. It is a very slight hesitation, but very noticeable, almost like a little "dead spot." If I take my foot off the brake and let it take off on its own for just a second or two and then throttle smoothly it is not there at all. If this is not normal, I want to do everything I can to get it fixed. It is driving me nuts.
View 13 RepliesFord 6.0L Power Stroke Diesel :: 2007 - No Boost - Hesitates While Accelerating?
My truck recently has been giving me the issue of wither having no boost , bogging down as its trying to excelerate , then going into overboost. It idles fine , i have cleaned out the egr . I'm at a complete list on what to do at this point the truck is a 2007 F250 6.0l
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Hesitates - Hard Start?
I have a 2006 f250 with a 6.0 and I am having some issues with a hesitation and lose of power. The hesitation is worse when under load and other times is not so bad. Also it is non existent at higher RPMs (2500 and up). I changed the egr valve 2 months ago and it seemed to fix the issue (95%) but now it is running bad again. I used Hot Shot oil additive 2,500 miles ago and I changed the fuel filters and changed to 5w 40 Rotella synthetic oil, nothing has changed. I had the FICM changed a year ago with new software updates, still didn't fix it 100%.
Now I am having a "hard" start issue. It takes a bit for the truck to turn over. My batteries are 12 months old and I just replaced the alternator so I am not sure how to proceed.
I did just buy a Scangauge II and I am still figuring out how to use it. It says there is no codes.