Ford 6.7L Power Stroke Diesel :: 2011 - Drive Shaft Making Clicking Noise?
My buddy has a 2011 250 and is having some weird issues with a clicking noise. It started out when you put the truck in gear (D or R) and touch the gas it would click. Seems to be coming from the middle to rear part of the truck. Now it clicks when he's driving. This all started after he got 35's and a leveling kit. It's taller springs in the front and added a block in the rear. It has less than 15k on it.
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2000 - Front Drive Shaft And Axle Locked In?
I am a new 6.7 owner and had/ have a 7.3 As I have been getting to know the truck I have been under it and noticed that the front drive shaft and axle are locked in. My hubs are switched to auto but I know on my 2000 7.3 when my hubs are on auto my front axle and driveshaft are disengaged... I'm wondering if the new 4x4 system is different. I know that can save on MPG
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 - Drive Shaft Pulled Out Of The Spline
2003 f350 6.0 diesel, driving on the freeway at 70 mph, all instrumentation went off, the radio went off, the engine was still running fine. While pulling off on the off ramp, when the speed was about 20 mph the rear end jumped up as if the transmission was trying to go into reverse. After traveling about 4 miles at about 15 mph the rear end jumped up about 6 inches and the drive shaft pulled out of the spline and drove itself into the pavement. Why this happened. I have put two new batteries and an alternator in the truck and it has been fine every since, but I am still concerned it may happen again. The truck has a 6 inch lift on it.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 - Drive Shaft Noise / Rear Pinion Seal Is Leaking
I was getting ready to replace the carrier bearing and noticed the rear pinion seal is leaking. Before attempting the replacement myself, I would like some opinions on the noise in the video below. Is this normal? I am confidant I can replace the carrier bearing and pinion seal, but not sure I have the tools for anything else.
YouTube ...
Ford 7.3L Power Stroke (1999-2003) :: Transmission Output Shaft Seal Removal
I'm trying to replace my transmission output shaft seal on my 2wd and I can't seem to get the seal removed. I couldn't find anything to rent from O'rielly's or Advance Autoparts that would work. It's in there really tight ....
View 10 RepliesFord - Aviator :: 2004 - Front Drive Shaft Removal?
I am wanting to remove my front drive shaft from my 2004 Aviator for a couple of month's while I save money to have my transfer case replaced. Are there any safety concerns with this? just need a couple of month's to get the money together....
View 5 RepliesPassat (B5) :: Right Side Drive Shaft Removal / Replacement
From what I've read, the procedure for removing and replacing the drive shaft involves pulling the upper ball joints and tie rod end from the steering knuckle--is it possible to put a floor jack below the lower arm (the load runs to the spring through the lower arm) and undo the lower ball joint to get the clearance required to remove the shaft?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Rear Drive Shaft U-Joint Replacement
What Spicer Part #s for the rear u-joints would be? I'm not nailing down the right one. I keep finding numerous ones, 1410, 1350, 5-160....
View 8 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Drive Shaft Removal To Grease The Center Spline
I'm wanting to grease the center spline on my drive shaft. I got the 4 bolts off with a 12mm 16 point boxed in wrench but can't get the drive shaft loose from the rea rend. I don't blindly want to go beating it out of the yoke with a hammer to try to knock it loose (but I will if I have to). What am I missing to get this shaft out?
View 3 RepliesLexus RX 2004-09 :: 2005 RX330 AWD - Back Drive Shaft Removal
I have Rx 330 2005 AWD, recently we dont have winters, so I don't need 4x4 . Is it possible to drive without the back drive shaft? It very easy to remove it, but is it save for e.g. differential or other mechanisms? By the way I could reduce fuel consumption, I think, 18miles/gallon is really too much for polish realities.
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Broken Shaft At 47000 Miles?
Just got a look at my 03' 6.0 turbo at Ford dealer. Truck still had boost but a real bad noise that was hard to describe. Pulled codes but no turbo code like the last turbo's. All the vanes were fine & no rust on the unison ring BUT the turbo shaft was broken. 3rd turbo went at 13,700 miles in July 2005 & now have 47,700 miles. I know I should drive it more but at 75 & having sold my boat it does't get driven to much.
I use Stanadyne with every tank full & drive it hard at least once every week to give the turo a workout. Use only Motorcraft oil every 3500 miles. Broken shaft on turbo would move about a 1/4 " on one end & a 1/2" on the other end. Ford service said they have seen shafts break before but said it was nothing I did to cause it.
Ford 6.0L Power Stroke Diesel :: 2003 F250 - Turbo Shaft Broken
Having a turbo shaft that broke? My 03 F250 turbo shaft was just replaced by the dealer, actually the whole turbo. This is the 4th turbo. Truck has 48000 miles on it. 1st 3 turbo's had sticking unison ring & vanes but this one had a broken shaft. Mechanic said unison ring & vanes were fine.
View 4 RepliesFord 6.0L Power Stroke Diesel :: Front Axle Shaft Seal Leaking?
I took the front axle shafts out a couple months back and remember NOT seeing any differential fluid in the axle shaft housing. But then when I took the tire off tonight.. I noticed diff fluid leaking from from the axle shaft dust seal ?
1. I didn't think diff fluid flowed up near those front dust seals ?
2. That's a brand new dust seal so I'm guessing some debri must be in the connection causing the leak ?
Ford 6.0L Power Stroke Diesel :: 2006 F350 - Clunking When Go From Drive To Reverse And Now With Drive Too
So I have a 06 350 and I'm getting clunking from drive to reverse and now with drive too, I know my rear diff is on it's last days but I am wondering if that could cause the clunking and now my truck around 90km shakes likes crazy and same thing wana know if that's the diff. And if I was to fix diff myself would it not just be easier for me to just swap axles if I wanted to be cheap??
View 12 RepliesFord 6.0L Power Stroke Diesel :: Cab Removal Without Shoplift?
Lifting a crew cab on an 05 6.0 with out a shop lift? I'm going to replace the head gaskets and install studs. I have removed many regular cabs with a tractor front end loader and a 4x5 timber thru the windows.
View 10 RepliesFord 6.0L Power Stroke Diesel :: Removal Of HUB Locking?
I posted about my steering issue and i went ahead and did the gear box and now on to the ujoints ...
HUB LOCK ASSEMBLY is in 2 i started to gently pry it out with a flat head in a star figure while jiggling and pulling the whole unit with my other hand well ...
The cover plate separated from the rest of the lock and I am lost ...
Ford 6.0L Power Stroke Diesel :: Front Rotors Removal From The Hub?
What's the best way to remove front rotors from the hub without damaging them on my F350 4X4?
View 7 RepliesFord 6.0L Power Stroke Diesel :: Radiator Removal To Do Oil Cooler?
I thought I remember a posting about removing the radiator to do the cooler because it made it easier to work standing in the engine bay with the engine in front of you instead of leaning over and removing everything from outside ? I'm getting ready to do my 4th external oil cooler? And is it difficult to remove radiator, and/or worth removing it ?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 - A/C Compressor Removal?
2005 F350 6 liter.
AC compressor clutch was toast. Thought it was just the clutch. Started to notice the truck struggling to start, with some smoke on acceleration that was not present before.
Today, paid a guy to replace my AC compressor clutch. He called me out a bit ago to show me what he found.
Looks like it was not the actual clutch. Looks like the bearing on the pulley took a crap. Bearings got wedged between the face of the pulley and the clutch. Mangled up the compressor clutch coil as well. The actual pulley, snapped off the bearing part. Pulley was only held on by the center bolt on the clutch hub. So, long story short, the compressor is locked up. Have to replace it.
This guy tells me he cannot do it, because to remove the compressor ,the motor has to be unbolted from the motor mounts and raised. Is this true? I have a service manual, that does not say anything about that at all. It does indicate that the compressor has to be removed with the third bolt loosened but still in place.
Can I get some info on the removal of the AC compressor in this truck? The idler/tensioner pulley has already been removed. The fan shroud has been removed.