Camry :: 1998 - Transmission Code P0755 / Shift Solenoid Valve 2 Malfunction

I have a 98 camry with code p0755 - shift solenoid valve#2 malfunction.-What are some of the most common causes. How to test it ,the issues that cause this and what to do also after replacing it if bad? Also are these to be replaced in pairs with both 1st -2nd shift and 2nd to 3rd shift .

If I have high miles on it will adding the 2 -3 quarts of new fluid give me issues as to mixing with the old and part breaking up in transmission(I've heard a lot happens when u replace very old fluid with new or flush it fully)..will be replacing filter also but not the rest of fluid still in transmission at this time. Looking for a link a pic. of the exact location on transmission inside pan .of it(looks similar to other shift solenoid near it )...

View 3 Replies

Ford Transmission :: 5R110W - Tow Haul Flashing On 2005 F250 - Code Is P0760 Shift Solenoid 3

2005 Ford F250 4x4 XL 5.4L 5R110W WITH 177,600 MILES... Tow Haul light flashed after 78 miles (along with other codes) after purchased. I purchased it used. While driving transmission would stop pulling as if it went into neutral and slam back into gear, at same time Tow Haul light be flashing...

Code is P0760 shift solenoid #3, I read from the forums on the site one caused could be the ground wire. We installed a ground strap from battery to tranny
Still does the same.

I have a shift solenoid ordered if needed, knowing the location of #3 solenoid in the tranny is the key to not having to keep dropping the pan. I love this site and have been reading it for long time.

View 9 Replies

Lexus GS 2006-11 :: Gear Won't Shift Past Third - Code P0751 Stuck Solenoid

I bought the car with 117k and never since my possession bothered to service it. Why? I kept putting it off well at 165k I said heck ill do it. Currently at 170k my gear wont shift past third and its reoccurring almost daily. When I first bought it it was intermittent. I think the late service messed it up. Here's the thing, aamco will open up my pan and look at my solenoids which is 250ish.

View 14 Replies

Ford Transmission :: Check Engine Code P0750 - Shift Solenoid A Malfunction?

My old 97 f-150's 4R70W started slipping.....so I just installed a rebuilt 98 f-150 unit that had about 10,000 miles on it and also has a transgo shift kit. Got it finished today....and.....

I have an check engine light code p0750 "shift solenoid A malfunction"........when leaving from a stop in Drive, the truck starts going in 2nd gear and just skips 1st gear all together. If I manually shift it, then 1st works fine and shifts through all the gears fine.

But in Drive.. it skips 1st. What to do? or what could be the problem? Where is this solenoid? Can I swap the one out of my old tranny into this one without pulling the whole tranny apart? (I don't mind dropping the pan though...) Or could i have a bad connection somewhere maybe?

Also....When the tranny shifts from 2nd to 3rd the rpms jump about 500 rpm before they drop...kind of seems excessive. Could this be caused by the shift solenoid A malfunction?

View 4 Replies

Lexus GS 2006-11 :: Code P0756 Shift Solenoid S2 Blocked Oil Passage / Stuck Open

Dealer said 90% bad ECU, 10% shift solenoid. ECU replace at dealer .. got code from auto zone, P0756 shift solenoid S2 blocked oil passage, stuck open. tranny shop took 2 days to confirm shift solenoid, changed out shift solenoid #2 35240, still have problem.. now they say it's ECU, rebuild my ECU.. what to do??!!

View 14 Replies

Accent LC (2000-05) :: Car Only Move On 3rd Gear - Error Code P0755

I drive hyundai accent 1.5l sohc.. Recently i was on my bots on turbo project.. The process when smoothly until i suddenly realized that my car was only move on 3rd gear.. then i took off my turbo out afraid of over boosting and straight go for diagnostic.. And error p0755 comes out.. So how to troubleshoot this problem..

View 9 Replies

Elantra MD (2010-15) :: Gear Shift Stuck / Burning Smell

I have 2011 Elantra at ~20,000 mile, and strange things started happening since last year...and it kinda blew up today.

My dashboard has been flickering randomly for a while, as in everything goes dark and turns up again in the middle of driving.

And today it turned off and turned on (as it usually does), and the dashboard seemed broken; speedometer stuck at 0 mph, rpm meter stuck at 0, all warning lights turned on, gas meter going up and down and stuff.

Fortunately enough I was close to home so I drove it back home, and my gear shift was stuck at neutral (I could switch b/w N and D).

So I took out the shift lock release? thing and managed to put the gear to P and pull my key out. I stepped out of my car and I smelled something burning...not a very good sign. What should I do? Well I think I need to take it to dealership tomorrow but I'm not sure if it'll be safe to drive...

View 4 Replies

Dodge - Neon :: CEL On - Transmission Control System And Shift Solenoid B Malfunction

I recently acquired a 2003 Dodge Neon and have also aquired a problem with the automatic transmission.The check engine light was on so I read the codes and they are noted below

P0700 Transmission Control System Malfunction
P0755 Shift Solenoid B Malfunction

Based upon some very basic research, I checked into replacing the Transmission Control solenoid.It sounded like this is a pretty common problem for this transmission, so hopefully this would fix the problem.

I was able to get the old one pulled off without to much trouble, but prir to installing the new one I was wondering if there would be a way to test the old one to verify that it was actually bad. I would prefer to not install the new $150 part only to find out that this was not the problem. (and then I could not return it once it had been installed) Maybe some low air pressure on the ports and verify that the ports / flow changes if 12 VDC is applied to the right pins?

A little more information in regards to the "failure" mode. The transmission appears to act the same no matter if it is placed in 1,3 or D. (reverse works fine) I would have expected that it would limit out with the motor taching up pretty high at about 20 MPH in 1(low). It goes down the road fine up to about 55 mph and then the engine starts taching up.

I also tried to reset the error codes with my "craftsman" code reader and it would not do it. I seem to recall seeing something about needing to reset codes before the new solenoid would work. Will pulling the battery for an hour clear the code? Do I need to clear the code?

View 1 Replies

Elantra MD (2010-15) :: 2012 Gear Shift - Car Would Startup But Stuck In Park

I don't know what is causing this but I bought a 2012 elantra last week (500 miles on it so far). Yesterday when I went to start my car the clicker wasn't opening or locking the doors so I had to use my key to open the door. When I got in my car would start but was "stuck" in park and I couldn't shift past park (yes I had my foot on the brake). After about 10 minutes it just randomly worked... Today I was driving to work stopped to get gas and as I was stopping I realized I couldn't shift passed neutral to put in park (I could go back and forth between drive and neutral). While this was going on my windows would not go up or down. Again after 10 minutes the problem seemed to fix itself. What could be causing this?

View 12 Replies

Passat (B5) :: 2001 Gear Stuck And Won't Shift Out Of Park

This is a car i am working on. 01 4motion passat. automatic. Tree fell on it. We put a new roof, quarter, door seats. Last night we moved it outside to clean the shop and went to move it back in. Won't shift out of park. Next tried turning ignition on the backing it off a little and cant get to neutral. Check fuses.

Brake light switch has been previously replaced by someone. and it works. Light next to gear selector working. brake lights fine. I have taken the center console out as much as I can. I can't get it completely out. But everything in there seems ok. When I press the brake in I don't hear any click or anything near the selector.

View 2 Replies

Santa FE SM (2001-06) :: Lost Ability To Shift Gear - Stuck In 2nd

My 2001 Santa Fe 2,4l - Have suddenly lost the abillity to shift gear. Its stuck in 2 and the shift stick is very loose in the "front to back and back to front" motion.. in other words there are resistance sideways.

I suspect it to be a broken shift cable. So my question is : changing shift cable on a santa fe easy? Is the best approach to start from inside the vehicle or from transmission side?

View 6 Replies

Elantra MD (2010-15) :: Code P0880 - Trans Stuck In 4th Gear

I have a 2011 Elantra 1.8 automatic Gls with 133k miles. While driving approximately 70 miles per hour the car downshifted to fourth gear, and would not shift up or down. I drove the car home and found that this is called "lump mode". I checked the codes, and found P0880 tcm voltage input. I replaced the fluid temperature sensor and harness, and checked continuity through the harness. I found no problems in the harness from the tcm to the solenoid connector. I then purchased a matching tcm, but the problem persisted. If the battery cable is left off for several days the problem will disappear until the car warms up.

View 4 Replies

Elantra XD (2001-06) :: Stuck In Second Gear

I have a Hyundai elantra 2002 that is stuck in second gear. I was driving it, I came to a stop sign so I put it in neutral and when I shifted into first i heard a pop. I started driving and when I shifted into second I noticed the shifter was really loose, when I tried shifting into third I couldn't.. it is like there is a brick wall. I can shift from 1st to 2nd but the shifter just moves up and down. Also if I let the clutch up it stalls the car. I was told that my car is stuck in second gear.

View 1 Replies

Santa FE SM (2001-06) :: 2004 - Auto Trans Stuck In 3rd Gear And Does Not Want To Shift

I have a 2004 Hyundai Santa Fe, has 99,000 miles 3.5L. After changing the alternator (alternator did die and drained my battery, the shop recharged the battery) now it seems be stuck in 3rd gear and does not wont to shift (it is a automatic). Fluids are good, transmission was flushed between 50-60,000 miles.

View 3 Replies

Elantra XD (2001-06) :: Car Would Slam Into 2nd / CEL Come On And It Get Stuck In 3rd Gear

I recently started getting transmission problems with my 2001 elantra.. the car would slam into second gear and the check engine light would come on and it get stuck in 3rd gear.. The codes I am getting are P0720, P0715, P1529. I searched and i found that most people that had this problem replaced the input and the output speed sensor and the problem is fixed.. so i went and i got two new sensors and replaced them i am still have the same exact problem... the car drives good for the first 5mins and then it would slam hard into gear, check engine light comes on the it get stuck in third gear...

View 6 Replies

Elantra XD (2001-06) :: Car Stuck Into 2nd Or 3rd Gear While Driving

2001 Hyundai Elantra 183 miles.

codes- p0720 output speed sensor circuit malfunction, p0500 veh speed sensor a malfunction.

Recent fixes on my 2001 Hyundai Elantra.

A few months ago i had my speed sensor cleaned, and a power steering leak. No problem after that was fixed and cleaned the sensor. Soon after that my water pump went bad and i had that replaced along with 3 new belts. Just last week i had my front driver side replaced with a new wheel bearing and axle.

My Problem then and now.

My problem months ago, my car would be shifting into different gears as it pleased; while driving or sitting at a light i would feel it jump and it felt as if it was stuck into 2nd or 3rd gear as i was driving. My engine light would soon come on after this. To accelerate i feel as if i had to floor my pedal when the shifting or engine light came on. I looked up my codes and they are the same as they are now. I read about same problem and fixed it by just cleaning the speed sensor off. My friend and i did the same thing and it fixed those issues. My problem now is that i just had my axle and wheel bearing fixed (my car moves smoother and quiet) my engine light came on again, it had not been on since, i read the codes and they are my speed sensor same as before but my car has not been shifting as it was in the past. Would this be because the sensor needs to be cleaned again or replaced, or because of my new replacements on my wheel.

View 1 Replies

Elantra XD (2001-06) :: Will Not Shift Out Of 2nd Gear?

My 98 elantra will not shift out of 2nd gear?...

View 4 Replies

Elantra XD (2001-06) :: Hyundai Won't Shift Into Gear While Driving?

The strangest thing happened to me on the way home yesterday from work. I was driving about 110 all the way home on a highway and took an exit to my local area when i noticed as i approached the ramp i wasn't able to shift into any gears. It just felt like there was something blocking me, like a wall of rubber or something. I stopped the car on the side of the road, unsure what was going on. While the car was on and my foot on the clutch, i am able to move into all gears perfectly fine but its when i start moving i cannot go into the others. Strange. I was able to force it into second gear from first but it sounded like two plates or discs sort of sliding around on each other..maybe that was my imagination but i stopped and didn't proceed further.

While i was sitting waiting for the tow truck, i remember that the last few months it has been getting harder and harder to get into gears while driving. I would be driving and would have some resistance to get into the pocket. This progressively got worse and i guess lead to this point where i am unable to get anywhere.

First thing i thought was the transmission, but i am able to go forward in first and reverse okay and the clutch pedal was not to the floor. The clutch was recently changed, approx 20k ago.

Could it be something easy to fix? Perhaps the clutch cable has stretched out and it is not pulling me far enough into the gears making it impossible to shift. Maybe the master or slave clutch cylinder have failed? I am not sure at all!

View 12 Replies

Elantra XD (2001-06) :: Gear Shift Lurched To The Left

I have an '01 Elantra 5 speed. Been great for 3 years. Replaced the clutch at 169000 km and it's been going really well.

It now has 186000 and just recently the gear shift lurched to the left (I did not notice exactly when it happened) but when I tried to shift down to 2nd it was noticeably more difficult to select. Selecting 1st or 2nd has become more difficult ever since.

It is certainly visible that the shift has moved because when 3rd is selected it looks like 1st is selected. I'm guessing a mounting bolt for the shift may have broken or dislodged.

View 3 Replies