Elantra XD (2001-06) :: Stuck In 3rd Gear - Code P0760 And P0755 / Malfunction Shift Solenoid B And C
I have two codes P0760 and P0755, malfunction shift solenoid B and C, today I took it to Hyundai here in queens ny, I was told that It would cost e 2684.00 to fix my issue, I can't believe that if those two codes are the problem why would it cost 2684.00 ? Where are these solenoids located?
The car feels like your one of the flintstones, it's stuck in 3rd gear and cant get out, then it jerks when it tries to shift, tranny oil is fine not burnt like if the clutches are gone.
Accent LC (2000-05) :: When Clutch Is In Gear Stick Will Not Move In Any Direction / Completely Stuck
Bought a 2001 hyundai accent 1.3 si petrol manual 2 weeks ago. After pulling off today, i went to go into 2nd gear, and I couldn't move the gear stick. I parked up and turned the engine off, then started the ignition again. When the clutch is in, the gear stick will not move in any direction, its completely stuck, but when the clutch is out, the gear stick will move in all directions.
View 6 RepliesAccent LC (2000-05) :: 2001 - Code P0121 TPS Error
2001 1.5L 5-speed Accent
I did a search on this problem and found several people posted the same P0121 code. Strangely many people wrote that replacing TPS did NOT fix it. The code came back in 30 miles or so. Most of them didn't follow up what finally fixed it and only 2 people did by saying they got the code cleared by fixing/replacing:
1. Leak in the intake manifold, bad plug wires, etc.
2. New Head & ECM.
Is there any known fix for the P0121 on Accent 1.5L other than above?
Accent LC (2000-05) :: Error Code P0442 Indicating A Leak In Evap Emissions
This began as a troubleshooting exercise for a P0442 code (2002 model) indicating a leak in the evap emissions system. Often caused by simple things like a loose/poorly sealing filler cap. Not this time
It's a neat design, tucked away up in the fender well. Even sports a very effective stone guard (plastic shield) which hides all that tubing from view. But the shield also traps all the road salt and mud and packs it into the crevices between the tubes where it stays from one winter till the next. Even a powerful car wash probably can't dislodge the caked on mess once solidified.
Accent LC (2000-05) :: P0734 Error Code - Hard To Shift Into Higher Gears
I inherited this car from my grandmother when she passed. It has low miles, around 40k. Since I paid zero for it, I would like to keep it. Historically I have done all my repairs, but never trans work.
Here are the symptoms. The car has issues shifting into higher gears. I have to punch the gas and then it will switch gears. It then began to do this for reverse, and now now reverse does not work at all.
At first I thought it was a speed sensor problem, but when I took it in to be read, it came up with P0734. It could be electrical (Speed sensor?), low fluid (it's not low), or 4th gear.
Is this transmission worth me fixing or paying to have it repaired, or should I move on?
P.S. If I drop the pan and find shavings, I understand that to point to 4th gear and bearing (also what the computer code read as the issue). Do shavings mean it definitely is 4th/bearing, or could it be another blown part?
Accent LC (2000-05) :: 2001 GSI - Check Engine Light / Mysterious P0300 Error Code
Mystery issue with my 2001 Accent GSI (5-speed manual, 1.6 L). I'm getting a P0300 error code and the Check Engine light (the light is like an old friend, I miss it when it's not on). This happened four months ago and I replaced the ignition coil - seemed to fix things - but now the light and the error is back with a vengeance. Car stumbles and runs rough. Changed the plugs and plug wires, but no difference.
BTW, there's a small pin hole in the upper part of the gas tank (just enough to give it a gassy smell when the tank is full) but I don't think the hole would be big enough at this stage to cause the check engine light to come on in the same way it does if you leave the gas cap off or loose.
Accent LC (2000-05) :: Check Engine Light Error Code P1128 / Too Lean Intake System
This is the infamous error code many Accent owners might have experienced it. The code refers to "Too lean intake system". People try to replace all kinds of parts like ECM, MAF, O2 Sensor, TPS, Fuel Pump, Fuel Filter, etc. according to my research. I just bought a 2001 Accent and the P2188 light came on. I wrote an email to Hyundai Corp. Asking what would be the most likely part that will cause the (P2188) check engine light to come on.
View 3 RepliesGolf IV / Jetta IV :: 2000 - Limp Mode / Stuck In 1st Gear And Error Code Of P0730
I have 1 month left on my AAMCO rebuilt transmission. I took it in a few weeks ago when it went into "limp mode" (Stuck in 1st gear). Eventually, they got an error code of P0730, which I believe is electrical-related. All was pretty good but then today, driving @ high speed on the interstate, I could not get into 4th gear...
View 1 RepliesAccent LC (2000-05) :: CE Light Code PO734 Which Is Gear 4 Incorrect Ratio
So I got around and decided to fix my transmission my self. Any way I got the code PO734 from my CE light which is gear 4 incorrect ratio. So some people say its the solenoids that cause this issue, some say its the 4th gear clutch...
So, Is it the solenoid or it could be the clutch itself? Ive removed the 4th gear from my transmission today and it looks intact. No weird damage or physical like damage on it... I just don't know which to do since solenoid job i can do myself which will be about 5 hours minimum....
Ford Transmission :: 1999 Expedition - CEL And Blinking OD Off Light - Code P0755
My wife drives a 99 ford expedition, 5.4, auto, 4x4, Sunday I am driving it and it wont upshift from 1st to 2nd unless I let off the gas or let it run up to 4000rpm. I have cel and blinking OD off light. I pulled the code and got a p0755 shift solenoid b. That is really the only symptom, the other shifts seem fine.
1st question, which transmission do I have? I believe it to be the 4r100, the pan has a "notch" in it. Looks like this... Fel-Pro TOS18714 - Automatic Transmission Gasket | O'Reilly Auto Parts
2nd question, if it is the 4r100 is there just a solenoid "pack" and not individual solenoids to replace? I found these...PowerTorque- TE140 - Solenoid | O'Reilly Auto Parts
PowerTorque - TE141 - Solenoid | O'Reilly Auto Parts
3rd question, what is the difference between the pwm and non pwm?
Camry :: 1998 - Transmission Code P0755 / Shift Solenoid Valve 2 Malfunction
I have a 98 camry with code p0755 - shift solenoid valve#2 malfunction.-What are some of the most common causes. How to test it ,the issues that cause this and what to do also after replacing it if bad? Also are these to be replaced in pairs with both 1st -2nd shift and 2nd to 3rd shift .
If I have high miles on it will adding the 2 -3 quarts of new fluid give me issues as to mixing with the old and part breaking up in transmission(I've heard a lot happens when u replace very old fluid with new or flush it fully)..will be replacing filter also but not the rest of fluid still in transmission at this time. Looking for a link a pic. of the exact location on transmission inside pan .of it(looks similar to other shift solenoid near it )...
Accent LC (2000-05) :: Rear Passenger Wheel Won't Move
I recently parked my 2001 Accent for the past year and now the rear passenger side wheel won't move. I'm assuming it has seized. I am trying to open the drum for the rear wheel but am not really sure how. The wheel is removed so is the Bolt locking the drum in place. Should it now just pull off? I have a read that it is possible the emergency break is whats causing it to seize up. How does one manually removing the parking break lock ?
View 2 RepliesAccent LC (2000-05) :: Can Move The Shifter Through Gears But It Won't Shift Up
What this may be. 2004 Accent Automatic. We just purchased recently for my daughters fist car. Today when leaving the house the car stays in first gear, you can move the shifter through the gears but it wont shift up. Reverse is fine. Checked the oil level in Neutral when hot and it was ok. Hooked up my code reader and there are no Codes. Car only has 85,000 KM on it.
View 5 RepliesAccent LC (2000-05) :: Stiff Accelerator Pedal / Have To Slightly Kick To Move It
My 2001 Hyundai accent hatchback with around 135000 miles is having problems with the gas pedal. I start my car and can't really push down the gas pedal smoothly. It is initially hard where I have to slightly kick the pedal to move it. Otherwise if I rest my foot on the pedal and try to press it down I end up press it down too much where my car goes flying. Every time I come to a stop I have to do that to get the pedal to move. Its not stiff once I get the pedal to push down some but once I take my foot off the pedal I have to slightly kick it back down.
View 4 RepliesAccent MC (2006-11) :: Misfire With Error Code P0302
2009 Accent, 1.6L 154,xxx Cylinder two misfire. Engine was rebuilt due to timing belt. Twice. Second time I did it. Replaced plugs, coil packs, all gaskets, (everything new in the head) did a smoke test, compression test 180 psi across all four, used a noid light for coil packs (good) did it at the injectors 1,3,4 did good, but 2 came on then went off. Check resistance and it shows good, replaced injector anyway and the connecter. Still doesn't work. Checked powers and grounds at the rail, good. Good solid voltage. I hooked up a scan tool and tried to shut injector 2 off, no change in RPM or vibration. Scan tool worked for 1,3,4. Used another PCM, still misfire in two. Even jumped a wire from PCM control and 15A inj fuse for the 12V constant (bypassed the harness) and still doesn't work. Also have knock sensor code, just two codes.
View 14 RepliesAccent LC (2000-05) :: Sputtering Quite A Bit In All Gears / CEL With Error Codes
Recently bought a `01 Accent 5 speed.. First question . How do I tell if its the 1.5 or 1.6 ? That will really point me in a good start. Ha... Ok.. Check engine light is on and I found a paper in the glove box with some of the codes wrong with it.. The one I focused on was telling me the fuel system was to lean . blah blah blah... Dont remember the exact code as I felt that my research was good and I replaced the MAF sensor... Didnt clear the code...
Also it was sputtering quite a bit in all gears mainly at low rpms. I did change the fuel filter , checked plugs and wires etc.. Now I replaced the MAF sensor and it has not solved the problem.. Took it to have it rescanned and have been given codes p1127 and p0136 .. both seem to relate to the Bank 1 sensor 2 O2 sensor. question is I have saw the "upstream" sensor located right below the exhaust manifold but did not see a second sensor?
From what I have gathered sensor 1 does the most work, so I`m curious if these 2 sensors are interchangeable? Could I buy the downstream sensor and if that does not solve my problem , take it out on try it in the upstream sensor? Also do you really feel as though just changing that sensor will "cure" my sputtering issue? the car only has 88k on it and seems to be in good shape otherwise.. I really need this check engine light problem fixed so I can get inspection..
Accent RB (2012+) :: Check Engine Light And P2191 Error Code
I got a 2012 Hyundai Accent SE manual 112000 mostly highway miles. For a month now I am getting the MIL on and P2191 code (System too lean at higher load bank1) after erasing the code it appeared again in 3-4 days. I replaced air filter check all valves and vacuum in air flow, changed to premium gas. Pipe that connected to the valve from EVAP system looks not damaged and valve works as intended. While changing spark plugs I noticed that all of them were quite charred. I am thinking to replace both O2 up/down stream sensors. Which not OEM sensors would be the best match for my Accent?
View 11 RepliesAccent MC (2006-11) :: 2009 - Low Purge Flow Error Code Popping Up
Not too terribly long ago I got assistance on identifying and fixing an engine misfire on my 2009 Accent. I assumed was directly connected has cropped up again - a P0497 Low Purge Flow error has come up on the car.
We recently replaced the purge flow valve, and everything seems to be running fine - there is no visible cause for the error, and I've even tried making sure I get the fuel cap as tight as possible.
The code is not popping up constantly - this is only the second time it's come up since the misfire was fixed(without obvious symptoms I always clear a code once just to make sure it wasn't a computer glitch), and the first time it popped up on it's own was the day after I fixed the misfire. Need to know what to check to find out what's wrong and, of course, how much priority I should place on fixing this issue.
Golf IV / Jetta IV :: Error Code - Car Stuck In 3rd Gear
Damn car is stuck in 3rd gear! Hooked up scanner and the screen just says error! I have to keep the scanner in the vehicle, hooked up, just to drive the car. That's just so it'll shift as its supposed to! Now it's not letting me pull the code out, in order for me to erase it! It just keeps saying "error".
View 1 Replies