Elantra MD (2010-15) :: Gear Shift Stuck / Burning Smell

I have 2011 Elantra at ~20,000 mile, and strange things started happening since last year...and it kinda blew up today.

My dashboard has been flickering randomly for a while, as in everything goes dark and turns up again in the middle of driving.

And today it turned off and turned on (as it usually does), and the dashboard seemed broken; speedometer stuck at 0 mph, rpm meter stuck at 0, all warning lights turned on, gas meter going up and down and stuff.

Fortunately enough I was close to home so I drove it back home, and my gear shift was stuck at neutral (I could switch b/w N and D).

So I took out the shift lock release? thing and managed to put the gear to P and pull my key out. I stepped out of my car and I smelled something burning...not a very good sign. What should I do? Well I think I need to take it to dealership tomorrow but I'm not sure if it'll be safe to drive...

View 4 Replies

Elantra MD (2010-15) :: 2012 - Car Won't Shift Into 5th Unless Manually Do It With Gear Lever

I have a 2012 Elantra Limited with about 36000 Miles. I purchased this car used with 12000 miles. I commute to work about 90 miles round trip a day mostly highway. I usually average about 33 or 34mpg. Recently, my mileage has fallen to 22 or 23 mpg and I have noticed my car having problems shifting. When accelerating normally, 1st - 3rd shift normally. Once I get into 4th, the car won't shift into 5th unless I manually do it with the gear lever or play with the throttle. If I just accelerate it will go all the way up to over 6000 rpm before it will shift. There are no problems with down shifting. Once it gets into 5th it will shift into 6th normally. There are not warning lights on and it doesn't always do it so of course when I need to recreate it I can't.

View 26 Replies

Elantra MD (2010-15) :: 2012 GL Jerking Whenever Switch The Gear From Park To Drive Or Reverse / Neutral

I have an Elantra 2012 sedan GL and last year i tried installing HID's. It worked for a whole but then it stopped after. I learned that it wasn't getting enough power so then yesterday I bought a wiring kit to be able to wire my HID to tap to the battery to get more power. Everything was fine till I got to work but when I had to leave work., there was an issue. Whenever i switch the gear from park to drive or reverse or neutral. My car seems to jerk. And when I'm driving and it changes gears, it also jerks. Kind of the same thing how if your driving a manual car and you change gears wrong. This happens when my lights are off. But when i turn them on it then stops. And when i turn it back of it doesn't do it anymore.

View 5 Replies

Passat (B5) :: 2001 Gear Stuck And Won't Shift Out Of Park

This is a car i am working on. 01 4motion passat. automatic. Tree fell on it. We put a new roof, quarter, door seats. Last night we moved it outside to clean the shop and went to move it back in. Won't shift out of park. Next tried turning ignition on the backing it off a little and cant get to neutral. Check fuses.

Brake light switch has been previously replaced by someone. and it works. Light next to gear selector working. brake lights fine. I have taken the center console out as much as I can. I can't get it completely out. But everything in there seems ok. When I press the brake in I don't hear any click or anything near the selector.

View 2 Replies

Ford - Explorer :: Gear Shift Stuck Between Park And Reverse?

I was pulling into my driveway. I put the car in park, but when i went to get out of the car, it started to roll forward. When I finally got it stopped, I tried to shift it, and it wouldn't shift to any spot. Then it became stuck in between Park and Reverse. I can't move the gear shift.

View 1 Replies

Ford F-150 - 1997-2003 :: Gear Shift - Stuck In Park

I have a '97 F150 Lariat Ext cab, 5.4, 2Wd, 175K, a bit rusty but for the most part functional. Unit is parked for long periods of time.

3 - 4 years back the gear shift did not want to go into PARK and and the gear indicator was out of register. Unit would not start and I had to move shift lever to N to start. Fixed the two screws on shift plate/column per this site. Then 18 months ago same thing begin to occur but this time I used blue thread lock to hold screws in place. Still had to throw into park to get it to stay.

6 months ago shifter became very difficult to move and near impossible to get into PARK. When in PARK the interlock must have not been engaged so had to move to N or push lever hard into PARK to start.

Tired of this so I cruised the site and found several posts on taking dash apart, repairing a broken shift tube and or replacing bushings.

Battery disconnected, dash apart, cluster out, steering wheel still on and steering column still in position. Shift tube appears OK, i.e. not broken as in one post, bushings appears OK as there is no play or slop evident, but I cannot get the shift lever to move from PARK, period.

When the shift lever is pulled toward the wheel, a pawl on the tube causes a plastic or nylon arm to move about 90 degrees. It must be a stop or safety of some sort. I have not dug deep enough to see the shift plate with the two screws. At 75 I find it difficult to lay upside down to reach and hope I can get to them from the top.

Questions:

1. How do I get it out of PARK to check all things on shift tube and gear selector units?
2. Does the battery need to be connected for the interlocks to function?
3. Do I need to drop the column to check on shift tube items?
4. With a rusty trans, can the shift cable to trans connection be the problem?
5. What to look for, how to repair. etc.

View 7 Replies

Ford F-150 (2004-2008) :: 2005 FX4 Truck Gear Shift Stuck In Park

My truck gear shift is stuck in Park (console type). I have been reading threads that discuss potential causes such as blown fuses, bad brake switch, bad brake shift interlock actuator, and even ignition switch. All fuses are okay. Before I try to get into all the other possibilities, I have a question around what the local auto parts worker suggested. He said that there is a small plastic piece that may have slipped down interfering with gear movement. This could make sense, especially since the white manual release lever doesn't seem to be moving.

View 14 Replies

Elantra XD (2001-06) :: Loud Thump When Go From Park To Reverse / Car Stuck In High Gear

What can I do about my car it's not shifting, it's stuck in high gear and when I go from park to reverse it makes a loud thump. The check engine light came on and the codes are transmission control module it's a 2006 and only has 30,000 miles on it. It's hard to believe it's the brain so we changed the fluid and cleaned the sylinoids but then when I drove it around the block I put it in reverse it didn't make the loud noise and it shifted fine for a minute before I got around the block and almost home it made a loud banging noise and went back to not shifting again. What the problem could be.

View 5 Replies

Elantra MD (2010-15) :: 2013 GLS Won't Shift Out Of Park

My 2013 Elantra won't shift out of park. I know that I should check fuses, but what fuses might be associated with this. (The brake lights are not affected)...

View 1 Replies

Elantra MD (2010-15) :: Hard To Shift From Drive Into Park

My wife called today after arriving at work letting me know she was having trouble shifting the car from D(drive) to P(park). I know the Gear box is set up in a stepped configuration. Sometimes its smooth shifting up to park and other times its not.

2011 Elantra Gls
Silver w/tinted windows

View 3 Replies

Elantra MD (2010-15) :: Started Fine But Wouldn't Shift Out Of Park

Went to start the car today and it started fine but wouldn't shift out of park, and the instrument panel lights were out. Got it towed to the dealer and they narrowed it down to a junction box or instrument panel cluster. They won't know until tomorrow what the problem is. What this might be?

View 6 Replies

Elantra XD (2001-06) :: Stuck In 3rd Gear - Code P0760 And P0755 / Malfunction Shift Solenoid B And C

I have two codes P0760 and P0755, malfunction shift solenoid B and C, today I took it to Hyundai here in queens ny, I was told that It would cost e 2684.00 to fix my issue, I can't believe that if those two codes are the problem why would it cost 2684.00 ? Where are these solenoids located?

The car feels like your one of the flintstones, it's stuck in 3rd gear and cant get out, then it jerks when it tries to shift, tranny oil is fine not burnt like if the clutches are gone.

View 2 Replies

Elantra MD (2010-15) :: 2012 - Oil Pressure Light At Startup

I have a 2012 Elantra with about 47,000 miles, and I've noticed that the oil pressure light comes on for about 2-3 seconds at startup. It never comes on while idling or driving, and the car runs like a champ. I checked the oil level, and it's good, and I get regular oil changes.

View 14 Replies

Elantra MD (2010-15) :: Cannot Shift From Park To Drive / Electric Windows Doesn't Work

I own a Elantra 2011 and I have a major problem. I cannot shift from PARK to DRIVE and my electric windows doesn't work either ! Everything else working fine and the car start normally !! The dealer cannot find the trouble and the car just have 19802 KM on it!!

View 3 Replies

Elantra MD (2010-15) :: 2012 Shakes When In Park Or Neutral

I have a 2012 Elantra with about 90,000 km. Everything was running smoothly until this week I ran into quite a few problems.

First of all, my car shakes when in park or neutral. I think this may have something to do with the idle being out of sync, but honestly I don't know enough to judge it.

Second of all, my engine was replaced twice by the manufacturer about 7-8 months ago. Now, all of a sudden, it is shaking like crazy! I'll open up the hood while the car is on and the engine looks like it wants to jump out at me.

Third of all, my window just started making a grinding noise when I bring it up and down. There's a section of the window, in the middle, where it doesn't make a noise, but for the rest of it it sounds like everything is scratching. I presume that this may be the power window and that I'll have to get this replaced.

View 3 Replies

Elantra MD (2010-15) :: Transmission Would Not Shift Gear Up Or Down

I have a 2013 Hyundai Elantra with an automatic with the Tiptronic transmission. last week I went to put the transmission into Tiptronic mode and it would not go in. it like crunch to the right and would not shift gear up or down nor would the gear number appear on the digital dash.

View 1 Replies

Elantra MD (2010-15) :: Code P0880 - Trans Stuck In 4th Gear

I have a 2011 Elantra 1.8 automatic Gls with 133k miles. While driving approximately 70 miles per hour the car downshifted to fourth gear, and would not shift up or down. I drove the car home and found that this is called "lump mode". I checked the codes, and found P0880 tcm voltage input. I replaced the fluid temperature sensor and harness, and checked continuity through the harness. I found no problems in the harness from the tcm to the solenoid connector. I then purchased a matching tcm, but the problem persisted. If the battery cable is left off for several days the problem will disappear until the car warms up.

View 4 Replies

Elantra MD (2010-15) :: Clunk Whenever Shift Into Gear At Low Speeds

My car has the clunk whenever I shift into gear (I have a manual) at low speeds and in low gears. Brought the car into the dealership and they think it's the front axles. Had one replaced (as they thought it was the passenger side axle) and clunk is still there. Went in to have the second one replaced, but part was not right. Waiting on the new part to arrive this week.

Axle? I honestly think it's tranny or gear related. Other than that, the car has been ok. I am going to work on sound deadening this week, getting my front strut bar installed and doing some research about the rear suspension.

View 8 Replies

Elantra MD (2010-15) :: 2012 - Maximum RPM Shift Points?

I had the opportunity to test my mother's 2012 non-GT Elantra automatic. In auto mode when I floored it, it shifted from 1st to 2nd at around 6,000RPM so it shifted too soon. I didn't try it in manual mode.

I have a feeling in manual mode, if I have it set to '1' and I continue to floor it , it won't reduce power at some point (say 6100RPM), but rather will automatically shift up for me?

What are the RPM points that it'll shift from 1st to 2nd and 2nd to 3rd when flooring it both in manual and auto mode? I hope there is a way for it to not shift until it reaches it's peak HP at 6,500RPM, if not the 6,750RPM redline at each gear change.

View 33 Replies