Ford F-150 (2004-2008) :: Shifter Stuck - Cannot Get The Truck To Shift Out Of Park Position
My son who is away at college, has a 04 F150 that has a center console and he can't get the truck to shift out of the 'Park' position. I told him to try and rock the truck back and forth and then try again...no luck.
View 1 RepliesFord F-150 (2004-2008) :: Stuck In Park - Can't Shift?
For the last couple of months, I am not able to push the button on the gear selector to change out of park. Twice I have had to give up and drive the wife's car. When I come back it works once and then it starts again.
View 8 RepliesFord F-150 (2004-2008) :: 2006 Truck Won't Start / Shifter Stuck In Park
I have a 2006 f150 fx4 4x4. I drove it home from work yesterday and it ran and drove just fine. I got up this morning to go to work and turn the key but the engine won't fire. I turns over just fine. I turn the key to release the trans to put it in neutral to see if it would start like that and the shifter is stuck. I button in the front will not go in. I tried lifting the rear tires off the ground to see if I could free the trans.
View 4 RepliesFord F-150 (2004-2008) :: 2007 Truck Do Not Shift Into 5th Gear
I have a 07 f150 getting 17 mpg in town, I would like to get 20 MPG in town, this is a 5 speed, i do not shift into 5th gear. Max in town in 40 MPH. I have 3.55... I was wondering would 3.27 getting me to that 20 MPG?
View 14 RepliesFord - Explorer :: Gear Shift Stuck Between Park And Reverse?
I was pulling into my driveway. I put the car in park, but when i went to get out of the car, it started to roll forward. When I finally got it stopped, I tried to shift it, and it wouldn't shift to any spot. Then it became stuck in between Park and Reverse. I can't move the gear shift.
View 1 RepliesFord F-150 - 1997-2003 :: Gear Shift - Stuck In Park
I have a '97 F150 Lariat Ext cab, 5.4, 2Wd, 175K, a bit rusty but for the most part functional. Unit is parked for long periods of time.
3 - 4 years back the gear shift did not want to go into PARK and and the gear indicator was out of register. Unit would not start and I had to move shift lever to N to start. Fixed the two screws on shift plate/column per this site. Then 18 months ago same thing begin to occur but this time I used blue thread lock to hold screws in place. Still had to throw into park to get it to stay.
6 months ago shifter became very difficult to move and near impossible to get into PARK. When in PARK the interlock must have not been engaged so had to move to N or push lever hard into PARK to start.
Tired of this so I cruised the site and found several posts on taking dash apart, repairing a broken shift tube and or replacing bushings.
Battery disconnected, dash apart, cluster out, steering wheel still on and steering column still in position. Shift tube appears OK, i.e. not broken as in one post, bushings appears OK as there is no play or slop evident, but I cannot get the shift lever to move from PARK, period.
When the shift lever is pulled toward the wheel, a pawl on the tube causes a plastic or nylon arm to move about 90 degrees. It must be a stop or safety of some sort. I have not dug deep enough to see the shift plate with the two screws. At 75 I find it difficult to lay upside down to reach and hope I can get to them from the top.
Questions:
1. How do I get it out of PARK to check all things on shift tube and gear selector units?
2. Does the battery need to be connected for the interlocks to function?
3. Do I need to drop the column to check on shift tube items?
4. With a rusty trans, can the shift cable to trans connection be the problem?
5. What to look for, how to repair. etc.
Ford F-150 - 1997-2003 :: 1998 - Brake Shift Interlock - Truck Stuck In Park
having problem w/ 98 f-150. first truck stuck in park. figured out how to get around that (turn key 1 position, shift to neutral, start vehicle, then engage transmission). but no brake lights! I have turn signals, driving lights, hazards, etc in rear. I disconnected harness from brake light switch. there are 2 leads, 1 hot, 1 not. i jumped them and no brake lights. i tested the switch and it functions properly (it's reconnected now). i changed my bulbs in tail lights. I unplugged the solenoid (which is impossibly located behind/beside steering column). this allowed me to shift like an old truck (without having to brake first), but doesn't solve my lack of brake lights (i've reattached the solenoid harness to remind me of my problems).
i am putting my money on a broken wire somewhere between the brake light switch (b/c that was good) and the solenoid (i am not hearing that faint click when i step on brake). but a broken wire should work by accident some of the time (unless cut cleanly and completely). there is a green wire with red stripe leaving the brake light switch and 3 wires at the solenoid harness (1 green and maybe a smaller gauge than those at the switch and 2 others which i don't recall their colors). Ford service manager doesn't think it's the solenoid but wasn't otherwise useful except to say, "hey, why don't you bring it in to me." What to look for before i plunk down for someone to perform what I already have before completing the job!
can i splice a wire from something (? brake light switch?) to something (?wire in solenoid harness?) or does that "electronic signal" get processed somewhere else first?
Passat (B5) :: 2001 Gear Stuck And Won't Shift Out Of Park
This is a car i am working on. 01 4motion passat. automatic. Tree fell on it. We put a new roof, quarter, door seats. Last night we moved it outside to clean the shop and went to move it back in. Won't shift out of park. Next tried turning ignition on the backing it off a little and cant get to neutral. Check fuses.
Brake light switch has been previously replaced by someone. and it works. Light next to gear selector working. brake lights fine. I have taken the center console out as much as I can. I can't get it completely out. But everything in there seems ok. When I press the brake in I don't hear any click or anything near the selector.
Ford Transmission :: Truck Moves Forward In Every Gear Including Park - Missing Shift Detent
Reverse band broke in my C4, I took it apart enough to get the rear band out and then reassembled. Everything to my knowledge was seated correctly and the front pump seated flush with the case when I reinstalled (which is supposedly a sign that it is all seated correctly). I adjusted the bands to spec and replaced the vacuum modulator and torque converter. These were the only things replaced besides the reverse/low band. Vac modulator was replaced to original (yellow band) as I was running an adjustable before. TC was replaced just because I did not the last time I had the trans rebuilt in 2003....decided to go ahead and R&R.
I got everything assembled, filled up with fluid and no leaks. I start it up and once i finished topping it off, the truck moves forward in every gear... including park! It also seems that I'm missing a shift detent. I have P, R, N, D, 2 but no 1. I disconnected the shift linkage and tried manually shifting from the trans and have the same issue.
I did not open up the valve body, just unbolted and replaced. When you start it up, it doesn't jump forward (while in park) but when you rev it up it sounds like the motor is under load. I've consulted my Haynes C4 book and an extensive google search and no way...
Elantra MD (2010-15) :: 2012 Gear Shift - Car Would Startup But Stuck In Park
I don't know what is causing this but I bought a 2012 elantra last week (500 miles on it so far). Yesterday when I went to start my car the clicker wasn't opening or locking the doors so I had to use my key to open the door. When I got in my car would start but was "stuck" in park and I couldn't shift past park (yes I had my foot on the brake). After about 10 minutes it just randomly worked... Today I was driving to work stopped to get gas and as I was stopping I realized I couldn't shift passed neutral to put in park (I could go back and forth between drive and neutral). While this was going on my windows would not go up or down. Again after 10 minutes the problem seemed to fix itself. What could be causing this?
View 12 RepliesFord F-150 (2004-2008) :: 2005 - Rattle And Vibration At Idle Only Occurs With The Truck In Gear And Stopped
My F-150 has developed a rattle and vibration at idle that only occurs with the truck in gear and stopped (with the brake depressed.) The noise appears to be coming from the front of the truck, perhaps from the driver's side (though it's difficult to tell while sitting in the cab).
Before I go crawling around underneath with my son holding the brake while the truck is in drive--I would sure like to know where it might be best to point the flashlight.
Ford :: 2004 - Gear Shift Sometimes Won't Start In Park And Has Slack In Movement
I have an 04 ford 150 super crew truck with 4 speed trans and 3.4 engine. The gear shift sometimes won't start in park and has slack in movement . Starts in neutral but has some slack in it. I can't determine where the slack is but sure it relates tt no park start. Where the safety switch is and is this a common problem with this truck?
View 3 RepliesFord F-150 (2004-2008) :: Truck Won't Come Out Of Park
2004 f150, Column shift Auto...
Today I stopped the truck put it into park and shut it off, everything worked fine, when I went to go start it back up it started but I cant put it out of park, I called FORD and they said put the key into the on position press the break as hard as you can and put it into neutral, we tried that and it didn't work, then they asked if we could move the truck because it could be struck or something still nothing... We tried the little cap and hold it to override the solenoid but it didn't work I dunno if I am doing it wrong so Is there any other things I can try or can you walk me through the override button here's what I did with that.
Opened the cap with a flat head
pushed it in
And started tried to shift
Is that what you do or what do you need to do??
Is there any way I could check the solenoid how do i take apart the column to do that?
Ford F-150 (2004-2008) :: Truck Would Start And Run But Won't Come Out Of Park
Just got an 04 f150 STX 4.6L Regular cab.
Drove fine for a few months (she's a little rough, but she does the trick).
The other day, I went out to go to work, truck would start and run, won't come out of park. Both turn signal indicators on the dash are illuminated, turn signals, flashers, radio and Climate controls do not work.
Currently driving with the emergency shifter release pulled out and zip tied open. First thought was interlock switch, but I'm not sure if that would affect everything else.
This happened once before, and I pulled all the taillights and checked all fuses, then it just seemed to work again after flipping the rheostat for the interior/dash lights. didn't work this time around.
Dash is all torn apart - where to start looking?
Ford F-150 (2004-2008) :: 2007 - Hard To Shift From Park Even On A Flat Surface
2007 F150 supercrew, sometimes it doesn't want to shift out of park even on a flat surface where its not torque locked.. is there an adjustment i can do myself?
View 2 RepliesLexus RX 2004-09 :: Engine Will Start But Gear Shift Won't Move Out Of Park
I have a 2004 RX with 82,000 miles, well maintained. Lately the engine will start but the warning lights won't go off and the gear shift won't move out of park. I have to keep turning the vehicle on and off until the gear shift will go in reverse.
It doesn't happen every day but off and on over the past month.I've had numerous brake light switches replaced which could maybe be the lights, would that affect the transmission too?
Prius (2004-09) :: Gear Shift Stuck In Neutral
I read a couple posts on Gear Shift switching back to neutral. Here is my situation. Got in the car to return some movies and realized I left them on the table. Went back to the house, and right before I turned into the driveway, noticed a metal coffee cup had come out of the holder and the edge was up under the accelerator. I had been applying my brakes to slow for the turn into the driveway, then when I went to accelerate, nothing, then noticed the cup.
Removed the cup and stepped on the gas to go into the driveway. Nothing. Turned the car off, then back on and tried to put into drive, goes a tiny bit then slips back into neutral. Tried it in reverse, same thing, pops back into neutral.
I can hold the shift lever in position and the car moves. It's in the driveway now and will get towed to the Toyota dealer tomorrow. Obviously a problem with the shifter as a result of the "coffee cup" under the edge of the accelerator. And yes, I know it's dangerous, hubby used the car last on his visit home this weekend and apparently the coffee cup either got put down on the floorboard or was knocked out. I bring it in the home when I'm done.....anyway.
So, the most likely cause was the spring talked about in other posts breaking, or a switch sticking or what. Seems like something got knocked or shifted out of adjustment. Does the accelerator have some type of cut off switch if something gets lodged under it?
Prius (2004-09) :: Gear Shift Stickiness Prevents Park Button Engagement
Today, I was parking the '05 Prius and noticed the gear shift stuck in the drive position instead of the usual "pop back" you experience when you put it in drive. The park button woud not engage. The same thing happens in reverse.
The dealer said they have had to replace the gear shift on a bunch of cars with this sticky gear shift problem.
Ford F-150 (2004-2008) :: Truck Idles High And Rough In Any Setting From Park To OD / Stopped Or Moving
I am trying to solve a mystery on my mom's truck. It's an '06 4.2L F-150 STX with about 133k miles. It had a check engine light on until today- I cleaned the TB and changed air filter yesterday, and both were filthy. Code vanished later on while driving.
I want to check the PCV because the truck idles high and rough in any setting from park to OD, stopped or moving. Worse when stopped though. Entire coil pack has already been changed due to previous misfire problems. This feels similar to a misfire but without the acceleration hesitation. It has also had a recent oil change, and fuel/oil filter change as well.
There is only one hose connecting to the intake on this truck, and it appears to be a vapor line of some sort to the valve cover, but isn't a PCV cause it's just a hollow tube. There is nothing else coming out of the TB at all, except for the throttle control cable. I don't even seen any nipples or connections or holes where a PCV hose or valve should go. I thought it was on the passenger side, under the TB... but there is nothing here at all. I'm stumped.
I am beginning to think the truck just does not have one at all, which I know for a fact is impossible. I have traced every line on this motor from top to bottom, and I do not see it. Should have a heater on it I assume? What else can make the truck so rough? I don't buy it that "it's just that way". That is complete, lazy, BS. I have had/driven many trucks; 4x4s, supercrew, diesels, jeeps, dump trucks... I have NEVER had a truck run as badly and roughly as this one does. Heck, a twin-turbo 700HP diesel doesn't run this roughly.