Ford - Escape :: Grinding Noise While Backing Out Of Driveway (downhill) And Pressed Brake Pedal
I have a 2008 Ford Escape, and today I noticed that while backing out of my driveway (downhill) as I pressed the brake pedal it made this grinding noise, but when I got out of the car I looked through the tires and the rotors and pads were fine. I did not get a chance to check the inner side of the rotor or pad yet. What else could this noise be if it's not the brakes? It only makes this noise when I press the brake pedal which is why I thought it was the brakes.
View 3 RepliesChevrolet - Malibu :: 2011 - Loud Humming Noise?
My 2011 malibu has approx. 20,000 miles, it makes a loud humming noise that is very annoying, can't even hear someone talking and must turn up the radio. It gets much worse when you get up to 55mph and above. I thought it might be the tires but they look good, but could it still be the tires?
View 5 RepliesChevrolet - Malibu :: Loud Roaring Noise When Accelerating
What could be causing a loud roaring noise when accelerating. I'm thinking it may be in the transmission but not for sure.1st I thought it was a CV joint going bad. Also acts like it's in 2nd gear. 2006 Malibu Maxx SS , 97,000 miles....
View 6 RepliesMalibu :: 2005 Base Cranks But Will Not Start Unless Gas Pedal Is Pressed
Malibu no start issue. It cranks, but will not start until she presses the gas pedal to floor. When it does start, it is a very low Idle but smooth. as soon as she lifts the gas, the car dies. Kinda like ran out of gas.
View 3 RepliesFord Transmission :: Loud Grinding Noise When Put Truck In Reverse
Chasing down a grinding noise. I have done a lot of research but nothing quit matches up with what I am hearing.
I have a 1979 F250 4x4. A few days ago I put the truck in reverse and as I was backing up it was like the drivetrain locked up. After that I put the truck in gear and started on my way. As I got up in speed a pretty loud grinding noise was coming from the tranny. 2nd and 3rd gear aren't bad but when I get up to 40+mph it sounds like crap. If I push in the clutch the grinding is still there. While driving I also put the transfer case in neutral, kept the tranny in gear, pushed in the clutch and the grinding stopped.
I also took the lid off, inspected the forks and thoroughly cleaned the inside but noise still continues.
Honda - Accord :: 1999 - Engine Dies When Pedal Pressed Down / Revs And Then Quits When Pedal Is Pressed Slowly
Ok, did an intake manifold cleaning on my 99 Accord the other day, and now I have problems...
Long story short, some time ago my car started to have a very rough idle. Took me awhile to find the problem. Turned out the air hose, between the filter and throttle body, had developed a big hole on the underside. So I replaced it and while I was at it used some throttle body cleaner, spraying into the intake manifold chamber. Lot of junk blew out the tailpipe. The car ran much better, but the idle could still be a little rough. I ran it that way for awhile, and finally the other day decided there was probably still some junk in there and it was time to really clean it out. So I took ff the throttle body and intake manifold housing. There was a lot of junk in there! The small intake on the passenger side was completely clogged shut. (I understand this isn't surprising on these cars.) I used a bunch of rags and 2 cans of Valvoline throttle body cleaner and a lot of elbow grease and cleaned it out. I was thinking to myself that whatever I didn't get with the rags flushed through OK, but I didn't want to take the whole intake manifold out.
So I put it all back together. (I took a video before I started, so I'm pretty sure it's all back together right.) But now I have problems. The car starts. It idles fine mostly, but can be a bit rough. But the trouble starts when I put the pedal down. If I do it in Park, well, if I push it quick the engine just dies. If I push it slow, the engine revs then quits, revs and quits, over and over. Similar if it's in gear. If I push it hard, the engine stalls. If I push it gentle, it revs up, but chugs along a bit.
I've run some seafoam through it, thinking it was clogged up with all that junk, and sure enough, lots of smoke comes out, but nothing is improving so far. What have I done wrong?
Passat (B6) :: Reverse Jumping Out Of Gear / Loud Grinding Noise And Pops Back In
I have a problem with my reverse in a 5 speed 105 hp Tdi. It jumps out of place when i try to move the car, makes a loud grinding noise and pops back in, I'm guessing the selectors are worn or maybe the teeth are too. My question is, how hard is it to replace the selectors (if it is the selectors that are worn of course), what is the cost of getting it done in the shop and most important does this sign mean I will have the same problems with the rest of the gear in nearby future?
View 2 RepliesSanta Fe (DM - 2013+) :: Metallic Grinding / Friction When Gas Pedal Pressed
I bought my SF 2013 Limited just less than 3 weeks ago. The car was fine but now all of sudden started to emit metallic grinding/friction noise when I press the gas pedal.
Dealer tech thought that it is bad drive shaft, but after changing it, it didn't solve the problem. Thought that rotor splash guards and maybe pads were to tight, that still didn't solve it.
To put this in perspective:
The sound comes only when I press the gas pedal and increases with the speed. It sound like cymbals and with speed it sound like a cricket. Noise comes from the bottom of the car and you can only hear it if your windows are down and car is passing sound reflection objects on the side, like other cars, concrete dividers, or parked vehicles.
Malibu - Chevrolet :: Grinding / Squealing After Brakes Applied?
Here's my issue, after a full break job my right front brake began to grind. Curiously it wouldn't grind initially after breaking soon after start up. I could go on and slow break for quite a distance, but soon after a hard brake or just slow breaking long enough the grinding begins. I've taken the car back to Firestone three times and even after a few adjustments or cleaning the problem persist... I've starting to feel bad for Firestone and embarrassed to be holding on to this 99 Chevy. I can't continue to drive this small car that sounds like a MTA bus while braking.
But I digress... I did notice, purely by accident (or it may be a mere coincidence), a few times the ABS light came on and during those periods the grinding was less abrasive. This leads me closer to believing the issue is with the caliper.
Volvo :: Loud Clunk Noise In Reverse - Roll Back When Press The Pedal
When I put my car (04 s60 2.5t) in reverse it hesitate, then when I press the pedal it roll back with a loud clunk noise. But if I put the car in drive before putting it in reverse everything goes smoothly.
View 2 RepliesChevrolet - S-10 :: 2003 - Loud Grating Noise / Reverse Gear Would Not Work
Not really even sure how to explain this problem. The other day while driving the car made a loud grating noise, which would stop if I kept giving it gas, but would persist while braking or simply slowing down naturally. This continued until I reached my destination (drove fine), but when I got home, my reverse gear would not work. I tried putting it into 4wd, and reverse worked again (and also in 2wd). What on earth is wrong w/ my truck?
View 1 RepliesChevrolet - Malibu :: 1999 - No Acceleration When Step On Gas Pedal
Started having problems with my Chevy Malibu (1999, with 95,000 miles on it) while driving two times this week. Both times an alert warning flashed on my dashboard. The first time, flashed the brake check and ABS warning on the left side of the dashboard, and the second time the check oil and check battery warning on the right side. In both cases, after the warnings flashed, the car was still running, but stepping on the gas pedal resulted in no acceleration, but brakes still worked. The steering wheel also locks-up to the point where I can't turn any more. Both times, I stopped and shut off the engine, waited about 30 seconds and restarted, after which everything is fine and normal. The brake pads were changed recently, but not the rotors which may not be in very good shape.
I took the car to garage and found the belt is good, but I have replaced both the alternator and battery, and also changed the brake pads. Car ran fine for a day. Yesterday while driving, had another issue of the accelerator not working while in the middle of driving. Was going up a small hill, tried to accelerate, but stepping on the accelerator didn't do anything. A few seconds later, I could not press down on the pedal anymore (as if the car was off). Brakes worked, I could turn, and no warning lights. Turned off ignition, restarted the car, and everything was fine. Same problem with the accelerator as I first reported, but no problem with charging or turning the wheel, and no warning lights since the alternator and battery are new.
Malibu - Chevrolet :: 1975 - Gas Pedal Slipped Off When Stepped On
My gas pedal wont work at all on my 1975 chevy malibu it feels like something slipped off when I stepped on it this morning....
View 2 RepliesChevrolet - Malibu :: Muffled And Gas Pedal Slow To React
I bought new 2009 maibu, changed oil every 3000, never had problem with car. Just thought because I have200k miles would be good to clean heads, had dealer put ina BG product. About 2 weeks after that the car see muffled and the gas peddle is slow to react,. Now six months later I am starting to smell gas. My guess catalytic converter.
View 5 RepliesChevrolet - Malibu :: 1999 - Hard Clunk When Put Car Into Reverse
I have a 1999 chevy malibu with a 2005 chevy impala motor in it. Recently I put my car into reverse and it made a hard clunk and went into reverse. Later on that day I tried to go into reverse and it will not reverse. I had to have 3 people push my car back in neutral. However, in neutral I am able to press on the gas and drive forward... This is an automatic transmission. Am I just screwed and need a brand new transmission?
View 12 RepliesChevrolet - Malibu :: 2005 - Idling Hard In Reverse
My car is idling hard in reverse, and the mechanic said, in fact, a problem with the transmission (a turbine?) Well, a new transmission costs much - so, not much savings there. I was told to try some simple fuel injector cleaner first. Chevy Malibu Classic, 2005....
View 4 RepliesMalibu - Chevrolet :: 2001 - The Brake Pedal Would Drop To The Floor While Driving
I bought a 2001 chevy malibu about a month and a half ago.when I test drove it,didnt notice any problems or leaks...after driving it for a 2 weeks...the brake pedal would drop to the floor while driving and then if I hit it again real quick it would be ok...this problem would happen now and then....we replaced the right front caliper thinking that it was sticking and bled all the brakes..There was air in the system..everything was fine for about two more weeks then while driving the pedal would get hard when applied and then drop again..not all the way to the floor,and it alternates that way..what are your thoughts? I don't have much money to fix this problem.
View 14 RepliesChevrolet - Malibu :: 2002 - ABS Light On / Brake Pedal And Steering Wheel Shakes
When I have to push on the brakes for a hard stop, I can feel the brake pedal and the steering wheel shake a whole lot. Also, he ABS light is on. Correlation between the 2 obviously?
View 10 RepliesFord - Explorer :: Grinding Noises When Depressing Gas Pedal / Placing In Reverse?
2004 Ford Explorer Sports Trac.
Just recently when driving down any road, when I let go of the gas to slow down from any speed, there is a funny grinding noise coming from under the truck, the Speedo drops fast, but the RPM`s stays the same. Then at around 30-40 km/hr, it just stops. When I place it into 4x4, I don`t have the problem. Also, again just recently, when I put the truck into reverse, I get the same grinding noise from under the truck. I have to putt he truck into 4x4, and then I put it in reverse for it to work.
I don`t have the problem going into drive. Both problems don't happen all the time, it will go away for 2-3 days then ill have problems for a few days after. I Took the truck to the shop and they said its the tranny so I replaced with a brand new one thinking that is the problem, but After the Tranny was replaced its still making all the same noises. The grinding noise sounds like "ice in a grinder" or to that effect. I'm not sure whats wrong, and I'm getting frustrated at my truck.