Camry :: 2002 - High Mount Brake Light On Spoiler Half Burnt Out
Just bought an 02' camry and the high mount brake light on the spoiler is half burnt out. Tried removing what I'm guessing is an LED assembly but the screws are stuck and the angle is really awkward. Am I going to have to replace the whole LED bar?
View 2 RepliesGolf IV R32 :: Noise From Clutch After New Mount Install
I finally decided to take the plunge and go with Stage 2 BFI inserts and mount.
Engine Setup (for reference):
EIP cold air
BFI Stage 2 Inserts and Mounts
Recently replaced clutch to brand new stock clutch
TT short shifter
First off, everything feels great. very solid mounts especially when compared to the spongy stock ones. definitely gets the job done.
Here's my question, is it normal to hear a lot of noise chatter coming from the clutch when not engaged? when my foot is on the clutch it goes away, and when i take my foot off a lot of noise starts coming from it. as far as i know, some clutch noise is relatively normal but I'm not sure if a lot is. also, when i start the car, the starter has a deeper, louder, more pronounced tone to it. not sure if that is normal or not either.
Golf/GTI VI :: Rough Clunking Noise After 034 Density Strut Mount Install
Setup: WRD Street Advantage Coilover kit. Installed and sit at 24.75" all around. 034 Density mounts and new bearings. 19,xxx mi.
7 weeks ago I installed WRD Street Advantage coils. The install went great, no problems. Drove a week or so and decided to replace the strut mounts with 034's density strut mounts and new bearing to get rid of the creaking sound at low speed. Ordered them and put them on this weekend. After driving it I realized the creaking of the old weaker strut mount was gone. However, I inherited a rough clunking or knocking sound (as if something is loose and moving around), which seems to be coming from my passenger side. This happens at all speeds and not specific to turning the wheel. I unistalled/reinstalled everything in the front 4 times and went through everything with a fine tooth comb, but can't find anything loose. All bolts are torqued to spec.
I even removed the sway bar end links and drove it, still there. So it's not the end links. I also tried using the OEM endlinks which are longer than the ones from WRD to increase the space between the axle and the sway bar, possibly thinking it was hitting and causing the noise. No luck, still there. The only thing I noticed is that with the car on jack stands the strut mount is tight to the body but I still have slight play in the spring and it's perch. Is that normal? I'm assuming under load it's tight again. So the only variable in my situation is the new Density Mounts and bearing, can these cause heightened noises due to the increased heardness of the mounts?
Ford Super Duty (1999-2016) :: Plow Mount Brush Guard Install
So I've had this WAAG brush guard laying around for a few years and figured it was time to do something with it. Of course it was bought with no mounting brackets. I had found a lower gear from a Fisher MM1 plow. Tossed the in the truck and started from there.
Broke out the cherry picker and started lining stuff up. Drilled some holes and bolted it up. It's all bolted up but I still need to take a piece of 2x3 angle and weld it to the lower plow mounts to tie the bottoms together and create a step.
Ford Super Duty (1999-2016) :: Install And Mount A Light Bar Without Drilling Into The Front Bumper Or Grill?
Any good way to install and mount a light bar without drilling into the front bumper or grill? I have a 32" LED bar I want to mount between the top of the bumper and bottom of the grill, but the mounts aren't ideal for where I want to put the light.
View 9 RepliesCamry :: Driver Side Of Front Spoiler Popped Out - Repair?
When I was leaving for work, I noticed that the driver side of my front spoiler popped out (where it meets the wheel well). I tried to push it in but it wouldn't stay. I saw that there are 2 slits that look like a point for something from the spoiler to clip onto the bumper but I see nothing on the spoiler that will clip to them. I have a 2007 SE.
View 1 RepliesCamry :: 2007 - Keeping Roof Spoiler Stuck To Rear Window
I am having trouble keeping the roof spoiler stuck to the rear window.
View 14 RepliesFord 6.7L Power Stroke Diesel :: How To Remove Chrome Piece Around The Cup Holders
How do you remove the chrome piece around the cup holders? I want to plasti-dip it so it quits shining in my eyes.
View 6 RepliesCamry 2012+ :: Mount GPS To Dash?
I have a round plastic disc and one side is tacky to stick to the dash. Are these things easy to remove off the dash years down the road? I'm also worried the circle will be discolored from the rest of the dash.
View 3 RepliesCamry :: How To Mount Fog Lights Securely On 2002 LE
I changed combination switch (got from junk yard $40) and added relay (from dealer $24). now plug has power as I turn fog switch lights on/off, but my bumper is solid. there is space but it's solid bumper
1. which fog light to buy?
2. how can I mount securely.
Camry :: Access Rear Top Strut Mount 2007
I have a rear rattle that I cant figure out had the wheel off and levered and pounded on links bushings etc. How can I access the top strut mounts to check them? Nothing found on youtube. Original struts on rear show no leaks or broken spring. Bouncing car does nothing neither does grabbing the tire at 12 and 6 or 3 and 9 position.
View 3 RepliesCamry :: Change All Support Mount Motor Of 2003 V2.4l?
I need to change the all support mount motor of my Camry 2003 v2.4l. but I don't know where find the best model or manufacturer.
View 2 RepliesCamry 2012+ :: Tow Hook License Plate Mount?
where to get it? I want to plug up my bumper holes and just put the plate on the tow hook.
View 14 RepliesFord Super Duty (1999-2016) :: Fairly Loud Noise Coming From Just Right Of Center Fold Down Cup Holders
The Truck: 2008 F350 Super Duty, Lariat Crew Cab 6.4 Diesel, Off Road package with just under 90K.
The Noise: It sounds like a cross between Morse code ticking (No Morse code message. I thought of that) and the sound a styrofoam cup makes when it rubs against another cup. The noise is fairly loud. Noticeable at standard conversation speaking levels. Doesn't just go away once it starts.
The Apparent Location Of The Noise: Sounds like it's coming from just right of my center fold down cup holders between the driver and passenger sides of the dash.
Process Of Elimination: No set rule for when it starts to happen but it doesn't happen all the time. SEEMS like it happens after a longer trip.
Air conditioning on or off doesn't make it stop. Fan on or off doesn't change anything. Restarting truck at a stop light doesn't change anything.
Varying truck speed doesn't make a difference. Banging on the dash near the sound doesn't make a difference.
Camry :: 2002 - Rattle / Noise With Replaced Dogbone Mount
I changed my dogbone mount over the weekend. Did not get a oem but got one from advance auto for 50 bucks. So I noticed a vibration when I'm in reverse or drive. I got some vids of the engine running. Could the cheap mount I got just be causing more vibration than the old one?? Which was cracked?
[URL].....
Camry 2012+ :: Cluster Dim After HID Install?
Maybe its supposed to do it, but I noticed tonight, that when the car is turned on and light switch it set to off, and then to either auto or on, the cluster lights dims from its normal intensity to less intense. Does that happen with the regular halogen bulbs as well ?I never really payed close attention to it before.
View 3 RepliesCamry 2012+ :: How To Install Entune In 2015 SE
I just got a 2015 Camry SE and I believe it did not come with Enture. Is it possible to install it on the current head unit or would i have to update the head unit ? also what would happen if i tried.
View 2 RepliesCamry 2012+ :: How To Install Shark Fin Antenna On XLE
How to install the shark fin antenna on the Camry 2012 XLE?
Does it improve the radio signal?
Where can I find the part number for the super white version?
Camry :: How To Install Bluetooth Mic Over Sunglasses Compartment
I want to install a bluetooth mic from my stereo into the pop-out compartment for the stock mic. I figure i'm going to have to go from the stereo behind the dash up to the left through the side panel next to the windshield, through the roof and into the compartment. How to pop these panels without breaking the clips.
View 10 Replies