Golf/GTI VI :: Rough Clunking Noise After 034 Density Strut Mount Install
Setup: WRD Street Advantage Coilover kit. Installed and sit at 24.75" all around. 034 Density mounts and new bearings. 19,xxx mi.
7 weeks ago I installed WRD Street Advantage coils. The install went great, no problems. Drove a week or so and decided to replace the strut mounts with 034's density strut mounts and new bearing to get rid of the creaking sound at low speed. Ordered them and put them on this weekend. After driving it I realized the creaking of the old weaker strut mount was gone. However, I inherited a rough clunking or knocking sound (as if something is loose and moving around), which seems to be coming from my passenger side. This happens at all speeds and not specific to turning the wheel. I unistalled/reinstalled everything in the front 4 times and went through everything with a fine tooth comb, but can't find anything loose. All bolts are torqued to spec.
I even removed the sway bar end links and drove it, still there. So it's not the end links. I also tried using the OEM endlinks which are longer than the ones from WRD to increase the space between the axle and the sway bar, possibly thinking it was hitting and causing the noise. No luck, still there. The only thing I noticed is that with the car on jack stands the strut mount is tight to the body but I still have slight play in the spring and it's perch. Is that normal? I'm assuming under load it's tight again. So the only variable in my situation is the new Density Mounts and bearing, can these cause heightened noises due to the increased heardness of the mounts?
Civic - Honda :: 1996 - Noise After New Clutch Install In Neutral?
Now with the new clutch installed, it makes a terrible noise with my foot off of the clutch in neutral. I can't get into any gears; it'll just grind gears.
Here is a video of the noise. Again the noise only occurs with my foot off of the clutch pedal. Quiet with my foot on the clutch. I can't get into any gears.
1996 Honda Civic
Camry :: Location Of Mount Holders To Install LE Spoiler?
I ordered a stock, LE spoiler to spice up my base model Camry. I read that it's installed through the factory mounting holes although, when I took off the interior trunk lid cover, I did not see any "existing mount holes". It actually looks like a tight squeeze/fit to get any type of tool to drill out or ratchet any mounting bolts down.
View 5 RepliesFord Super Duty (1999-2016) :: Plow Mount Brush Guard Install
So I've had this WAAG brush guard laying around for a few years and figured it was time to do something with it. Of course it was bought with no mounting brackets. I had found a lower gear from a Fisher MM1 plow. Tossed the in the truck and started from there.
Broke out the cherry picker and started lining stuff up. Drilled some holes and bolted it up. It's all bolted up but I still need to take a piece of 2x3 angle and weld it to the lower plow mounts to tie the bottoms together and create a step.
Ford Super Duty (1999-2016) :: Install And Mount A Light Bar Without Drilling Into The Front Bumper Or Grill?
Any good way to install and mount a light bar without drilling into the front bumper or grill? I have a 32" LED bar I want to mount between the top of the bumper and bottom of the grill, but the mounts aren't ideal for where I want to put the light.
View 9 RepliesGolf V R32 :: Noise From Shock Mount While Turning?
I already checked for spacers, none found. It is kind of like they're seizing up or something, when parking and moving slowly, like out of my driveway, they make a terrible noise.
View 9 RepliesGolf IV R32 :: Popping And Clunking Noise From Passenger Side Spring / Mount Area
I had the struts replaced a few months ago along with the strut mounts and bearings. Since then I've developed a popping and clunking noise from the passenger side spring/mount area. I've greased it and it has quieted it down but I noticed that when the car is not moving and I turn the wheel from lock to lock that very top piece of the strut pretty sure it's called the hat moves along with the wheels while the drivers side does not. What's wrong? Is it something as simple as the nut being to lose or to tight?
View 3 RepliesGolf/GTI VI :: Plastic Rattle Noise After APR Stage 1 Install
It sounds like a plastic on plastic rattle coming from the dash area. The sound comes loudly through the vents, so I am thinking it is something under the hood. Bumps make it much worse. No relationship to whether I am on the throttle or not.
View 9 RepliesGolf VI R :: Rattle Noise Coming From CAI After Turbo-back Install
Is it normal to have this rattle noise that is coming from the CAI which i never noticed before? This only happened after installing a turbo back and car runs fine. It just sounded like marble got sucked in the intake or 2 thick plates banging. I am pretty sure its not the heat shield for the filter also because i tried holding that and looked at that part. Went under the car too but i cant pinpoint where its coming from but maybe inside the engine?
[URL] ....
I also got a pronounce rattling at 2000 rpm when I let go of the gas that's located maybe at the bottom passenger side. I am thinking fuel lines?
Golf V R32 :: Clunk Noise Coming From Right Front After H&R Springs Install
My R's only got 5,400 miles on it and I just lowered it Saturday on H&R Springs and when I turn my steering wheel like 3/4 either way it makes like a clunk noise at lower speeds only....any other part besides strut top mounts and bearings? It sounds like its coming from the right front.
View 9 RepliesGolf/GTI VII :: Squeaking Noise From Driver Side When Go Over Bumps After VWR Spring Install
Instead a set of VWR springs yesterday on my GTI. Initially driving it, everything seemed fine. After about 20 miles and taking an off ramp aggressively, I noticed a squeaking noise from my drivers side when I go over bumps. I cannot pin point what may be causing it.
View 11 RepliesGTI 337/20th Anniversary :: Bucking / Limp / Hesitation After Clutch Install
I took my car in for a clutch install, everything was fine except the clutch slipping. I go to pick up my car and once the car warmed up it started bucking / limp mode while accelerating. Take it back to the mechanic and he thinks he didn't reset the throttle body. So he says that should be it and I pull away. Same thing. Leave it with him again and he replaces with "diag" coils and new plugs. Leave again, same thing. He tells me to get totally new coils and try that. I am thinking its a missed ground cable or messed up ECU or something. During all this not one code it thrown.
20th GTI 1.8T 6 speed, stock clutch, all stock
Ford Ranger / B-Series :: 1993 - Clutch Release Bearing Install
93 Ranger, 4.0 liter, 4WD.....
Putting in a new clutch and clutch release bearing, and am wondering if I need to put the retaining ring in that came with the new clutch release bearing? When I took off the old release bearing, a ring did come off from somewhere, but I did not see where it was because it was so dirty.
The reason I ask is because my Haynes manual did not even mention a ring, so I was surprised to see one come off. And my manual does not say to reinstall the ring when installing the release bearing. I did get a newer Haynes manual at the library and looked through a bunch of Chilton, etc manuals.
The newer Haynes manual says to remove the retaining ring on 97 and newer models, but says nothing about putting it back in when reinstalling. So, I am not certain if I need to put a new retaining ring in with the new release bearing.
Golf/GTI VII :: Spring Binding Popping Noise After Neuspeed Race Spring Install
This noise I have is driving me crazy, installed neuspeed race springs and now I have this weird spring noise, sounds like the springs are binding and then releasing when you turn the wheel, like a clicking dinging noise, it's on both sides and happens when moving slow and turning the wheel and when stationary and turning wheel, it sounds like tug and release not really spring bind I checked install and everything is correct even disassembled bearing assembly and everything is fine, lubed spring seats with silicone paste nothing is working.
When looking at the spring and turning wheel it's almost like the spring is getting stuck on the middle part of the seat then releasing, I know this was a common problem on the mk6 but I haven't heard anything about the mk7 the spring is seated in the lower perch perfectly the upper is were the noise is coming from you can see as you turn the upper bearing by hand it actually somewhat twists the spring and then releases and that's what makes the noise, and it dose not move in a nice circular motion kind of like an egg shaped rotation and it makes the spring flex and pop I think there's a problem with the springs,
Golf/GTI VI :: Rattling Noise Whenever Let Off The Clutch
I am a new owner of a 2011 Tomato Red GTI and was wondering if the sound my car makes is normal. Whenever I let off the clutch the car makes a rattling noise and i can feel it with my foot. Is that normal in our cars?
View 13 RepliesGolf/GTI VI :: Noise After Clutch Upgrade?
just got a clutch job done. old clutchmasters was slipping so i went with a used southbend stage 2. the clutch was used for 3,000 miles or so and it belonged to the owner of the shop where i got it done. he guaranteed me that the noise was fine, but my father thinks differently. only makes noise when clutch is disengaged. if i press the clutch pedal. the noise goes away.
he shop resused my old stock flywheel but swapped out the clutchdisk and pressure plate. not sure if he switched out the throw out bearing.
is this normal in a higher stage clutch? its worth noting that all weird noises aside, the clutch shifts very smooth compared to my beat up CM kit (never buying anything from CM again) i cant test to see if it holds since ive only driven 50 miles on it
Golf/GTI VI :: Knocking Noise When Idle, Clutch Is Not Used
I bought my 2014 GTI TUESDAY... In less than 24 hours, I noticed a knock when the car was at idle with the clutch not in. Went away once the clutch was in. The car has 248 miles on it.
I am thinking it is the throw out bearing, but vw service seems to think it is nothing and they want to just run some tests and keep it for the weeknd. In all reality, I will have the rental longer than I actually had my brand new car.
Golf/GTI VI :: Chattering Noise When Clutch Disengaged?
So I don't know how long my car has been doing this I have only had it for about 2 weeks and was wondering if its normal.. I can hear like a chattering sound when my foot is off the clutch when I am idling but if I depress it and engage it there is no more noise( I'm sure when I'm driving its doing it too but with the other stuff going on I can't here it when I'm driving) . Is it normal or somewhat normal or should I be worried and go and have it checked?
View 5 RepliesGolf VI R :: Clutch Noise When Downshifting On Compression
I have a strange noise issue on the clutch since day 1. When on regular driving, if I'm decelerating on compression and downshifting from 4 to 3, and 3 to 2nd (like slowing down to stop at a red light), when a release the clutch slowly, at the friction point, I am hearing a scratch noise, like 2 metal parts are touching each other.
When totally depressed, no problem, when totally pressed no problem too. Only at the friction point. It's more noticeable when downshifting from 4 to 2.