Accent MC (2006-11) :: 2008 GS - Misfire On 3 Cylinders / Rough Idle And Poor Acceleration
After scouring through hundreds of threads on this forum (which is Awesome, BTW), it seems as if this misfire / rough idle thing is fairly common (which is scary!!). CEL is on steady. Had the codes pulled; P0301, P0302, P0303. At the recommendation of the mechanic, I had the plugs replaced...no improvement. He then replaced the ignition coils...no improvement. Just finished replacing the MAP sensor. This actually had a VERY temporary positive effect. However, after about 5 miles of driving, the misfiring returned. Took the car to the Hyundai dealership, and they acted as if they didn't want to fool with it. They referred me to a couple of local repair shops...????
View 8 RepliesGolf/GTI VI :: Cylinders Misfiring Lost Acceleration
So last night i was driving and i made a turn onto the highway and speed up to pass this slow ass car :thumb down: and as i did i lost acceleration and my car started to rumble like when you use a high gear when u make a turn while moving that slow acceleration. And as that happened my engine light turned on and my EPC so i drove it well barely made it home. i had a friend with his VAGCOM come to see whats wrong it said cylinder 1&3 are miss firing so he took his ignition coils out of his car swapped them in my car and we drove it around and it drove fine and no fault codes. so now my issue since i have GIAC, CAI and APR full exhaust if my warranty will cover to have them put new ignition coils since i did get an extended warranty. I'm just afraid they won't.
View 7 RepliesGolf IV / Jetta IV :: 2000 - Bogs Under Acceleration - Cylinders Misfiring?
My friend has 2000 12v vr6 auto and recently he experienced his car bogging under acceleration. He had the plugs and wires recently done to solve the problem and the problem went away for a day and has since returned. I scanned it and here are the codes that its threw. After doing some research i'm thinking its the coil pack, since it was pretty foggy/damp today (when the problem started again).
17626.p1218 - fuel injector for cylinder 6 (N84): short to b+
16690.p0306 - Cylinder 6 Misfire Detected
16684.p0300 - Random/Multiple Cylinder Misfire Detected
Hyundai - Accent :: Multiple Misfiring - Operating Stuck On 3 Cylinders
So my 2008 accent is my daily driver. I'm nearing the 300,000 mile mark but the last 100,000 miles have been plagued with random multiple misfires. I have changed the cables, crankshaft sensor, plugs, and I've been through numerous costly coils (I keep 4 with me). All listed parts were most recently changed at the same time. Why do I misfire on nearly every commute and get stuck operating on 3 cylinders?
View 11 RepliesAccent MC (2006-11) :: 1.6L Engine Started Misfiring
I have a 2011 Hyundai Accent 1.6L. A few weeks after I bought it w 38,000 miles, it started misfiring so I replaced the spark plugs. It ran great for about another 6 months and started misfiring again. I took it to Hyundai to have it fixed and of course it wouldn't do it for them. I told them what it was doing and they said that there was no code so it was probably my spark plugs. I replaced my plugs with the OE plugs and got the same trouble about 4 months later. Now it has 60,000 miles and my warranty is done. I put in new plugs yesterday and it only ran well until it warmed up and it did the same thing. I ordered new, better than OE Delphi coils yesterday and I'll get them today. I feel like there's a bigger problem with the system that's causing the problem with the coils.
View 7 RepliesAccent LC (2000-05) :: 2000 - Misfiring Upon Acceleration And Engine Revving
I have a 2000 accent. Automatic tranny with 167000 miles. My current problem is the car is misfiring upon acceleration and engine revving. I have to accelerate very slowly to minimize this but i once the engine revs up enough I can give it more gas and it will rev normally with plenty of power. I have had to unplug the maf to keep it driveable. Ive never had a car stay running after disconnecting the maf so this is strange to me. My accent barely stays running with the maf connected. I just got the car from my dad and he had it fixed and it ran good for awhile with the maf connected so I don't think it is the maf. But the same problem came about and we had to disconnect the maf again. And he cant remember or is not sure what was exactly fixed on the car. I've read up about the purge control valve and havent had a chance to check it out but some of the symptoms fit.
View 21 RepliesAccent MC (2006-11) :: 2007 - Engine Woes / Really Rough And Shaking
2007 Accent Hatchback. Put gas in it from an Exxon we have bought from before with no problems. My kids car, running on vapors, put 1/2 tank of gas in. Pulled out of gas station and car starts running really rough, shaking. Still running though. I have gathered some knowledge from other threads, like timing belt needs to be changed (65000 on car). I replaced the plugs as an initial attempt at correcting the problem. Runs better, not great. Saw a thread with changing to better gas, will try that.
View 11 RepliesC/K :: 1994 1500 5.7 Liter Engine Skipping / Misfiring - Truck Running On Half The Cylinders
My truck is skipping but if I give it more throttle it will stop but then will start back when I let off the throttle. It seems like it is only running on half the cylinders. This problem is intermittent which makes it very hard to troubleshoot even for the dealership and other places I have taken it. Also, the problem is temperature sensitive. It only does it below 40 deg. F. Truck runs fine any other time of the year. Truck has new plugs, plug wires, distributor, egr valve, O2 sensor. Also, the IAC has been cleaned. The check engine light does not come on.
View 14 RepliesPrius (2001-03) :: Misfiring On Random Cylinders - Engine System / Ignition Circuit Malfunction
Started this winter as a misfire on random cylinders. I replaced all apart plugs and verified the gap. Replaced all the coils. Still occurred during the cold months. Once it warmed up it went away for a short while. The only codes present at the time were random misfire codes. Took it to a shop and they told me the injector was bad on cyl 1. Today I replaced the injectors with a matched set of 4 matched flow Denzo remand. Ran it on the TIS tech tool and was given a barrage of codes. I can unplug #1 coil and it will smooth out and stall within 90 seconds. Engine runs rough. Intake was just done as well. From Toyota TIS
P3191 – engine didnt start
P3000 - Battery Control System
P3101 – engine system malfunction
P3190 – poor engine power
P1300 - ignition circuit malfunction #1
P0303
P0302
P0301
P0300
c1259 - ABS error code meaning problem with regenerative braking. Probably caused by me forcing the car to recharge the HV while misfiring. HV battery was getting dangerously low from sitting for the last 6 months.
b0116 – LH airbag circut
Sonata NF (2006-10) :: Random Misfiring At Idle And Shaking Really Bad
My car has had random misfiring when at idle and has been shaking really bad but once I accelerate and get up to speed the vibrations and misfiring stop but the check engine light flashes for a few minutes. I have changed spark plugs, all 6 ignition coils the intake manifold gasket and both camshaft position sensors. My car has 180K the codes that are showing up are 300,301,303 and 0016. I really love the car and have had no prior issues the car before this ran like a champ.
View 2 RepliesAccent MC (2006-11) :: Engine Valve Knocking On Slow Acceleration
I have yet another issue with my Hyundai Accent. It seems to me that I hear engine valve knocking. Here tech. details:
- This happens around 1100-2000 rpm.
- The car currently has 11500 KM.
- 3 oil changes so far - using Mobil 1 - 10W30.
- I put in regular gas.
- No mods, only bug guard.
I drive slow - slow acceleration and I noticed sometime ago that there was a knock coming from an engine at about 1400-1700 RPM, however now I can hear it anywhere from 1100 to 2000 rpm. I can hear it very well when I drive along curbs and walls since engine sound bounces off it. I have automatic gear box and therefore I don't know how to test it further ( on manual I would have put some load on the engine by switching into high gear and pressing gas - make engine struggle a bit ). It might be noise from injector but I don't know. Also I don't know if Accent 2010 has self-adjusting valves or not.
Accent MC (2006-11) :: 2009 - Fuel Not Getting To Cylinders
I have a 2009 accent.. fuel pump went so I just replaced it...it pumps fuel but not getting any fuel to the cylinders...had a plug out to test the spark and it has good spark but plugs were dry and very faint fuel smell...also changed the crankshaft position sensor.. what could cause a no fuel issue??car ran fine, shut it off and no start..checked the fuel pump and it wasn't working though it had power to it...why the injectors wouldn't be working??
View 12 RepliesAccent MC (2006-11) :: Misfire On 2 Cylinders - Location Of MAF Sensor?
I have a 2009 Hyundai accent. 2 cylinders misfire. I changed out the spark plugs after the misfiring began and the 2 cylinders that misfire don't follow any specific ignition coil, it's just 2 random ones.
Looking at the data with a reader points to fuel injector number 1 not working properly. The first few seconds the car is on the check engine light blinks and fuel injector 1 spray duration (fluctuates based on gas applied) changes just like all the others. However, when the check engine light goes solid (then the misfire code is thrown) fuel injector 1's spray duration is stuck (usually around 3.5 ms)
The cable going into the fuel injector powers those little troubleshooting lights like it should until you plug the cable into the fuel injector OR remove and replace the light a few times.
I don't know much about cars but someone told me to try cleaning out the Mass AirFlow sensor as they had the problem above and the MAF sensor was the cause. I can't find anything on where the MAF sensor is located though.
Accent MC (2006-11) :: Engine Stumbles And White Smoke Pours From Tailpipe Upon Acceleration
I've got 120,000 on my 08 manual Accent. Recently I've been getting white smoke after running it hard. It happens like this. I slow down from 70mph or so with the clutch engaged to about 40mph, then upon acceleration the engine stumbles and white smoke pours from the tailpipe. My guess is a leaky head gasket.
I had the dealer go through it. They pressure tested the cylinders and put a scope in them. They claim nothing is wrong with the engine.
I mentioned since they can vouch for the engine now, I'd like to get an estimate on trade in value. I don't think I want to keep it much longer.
Accent MC (2006-11) :: Misfiring On Idle - No Code
Recently got broadsided (passenger), got the body fixed up. Now it is Misfiring on idle and only on idle...
Prior to this I had Coil go out on me, got that changed out, changed the spark plugs. It was running great then the accident happened an this Misfire on idle problem.
Took it to the shop, had them check for a code, no code. They suggested that it made be do to carbon buildup from the previous misfiring issue and suggested using STP engine treatment on it.
Ford - Explorer :: 1999 - Misfiring / Shaking / Rough Idle - Engine Light Flashing
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesnt stall very often at all. Accelerating I notice way less power and the engine studders. Thats when the engine light comes on flashing. Then remains on solid afterwards.
I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as O2 censor. I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gapping. Thought I had fixed the problem. Vehicle ran perfect. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it.
Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
Accent MC (2006-11) :: Misfiring / Intermittently Kind Of Choke
Have a Accent GLS 1.6L, 92,000 miles on it the issue is what I stated above.
Basically back in March I started having issues with my car and it seemed like it was misfiring or something of the sorts at first I thought it was the IAC motor because it would only intermittently kind of "choke" if you will and it only did it while I was idling and in drive. So before I decided to go further with the IAC motor I decided to take it and have the throttle body cleaned, but it eventually started to do it again. After that I had my fuel injectors cleaned and that didn't work much at all. Kept going until a couple months ago when it actually set off a check engine light and it started doing it almost violently.
Check engine light came up with the result that coil 2 is misfiring and I went about replacing the spark plugs and the boot to one of the coils and that made the issue go away no check engine light, no nothing. Past couple days it's been doing it very very occasionally but yet still doing it.
I don't have a whole lot of cash but I need a solution quickly because this is starting to become a pain I don't want it to become so bad that I'm without a vehicle that is operating properly again.
Only thing I can note is that now it is very occasional, and when the car could be otherwise be considered "cold" and often I can't make it repeat the same thing. Had oil above cylinders when I had the plugs replaced.
Accent MC (2006-11) :: Misfiring Followed By CEL Coming On And A Cylinder Cutting Out
I'm having the absolute worst time trying to fix my wife's 09 accent. We bought the car in '12 with 45k miles on it, and just hit 109k last month. About a year ago, the car started misfiring badly (hot day, after reaching operating temperature) followed by the CEL coming on, and a cylinder cutting out. I (mistakenly) figured coils, and replaced them. This "fix" didn't last more than a couple months.
I've also replaced the intake manifold gasket, suspecting a vacuum issue, due to the symptoms. While doing that, I put in a new PCV valve. To no avail, as the car still misses, chugs and shudders while accelerating at operating temperature. I've disconnected/checked the sensors on the manifold, the 02 sensors, the evap purge solenoid...I absolutely can not wrap my head around this.
The weird part is that the car starts fine when cold, (with only a split-second hesitation if you goose the throttle) and will run great for about 10 minutes/until it warms up. Then,once it warms up it will jerk, shudder and not accelerate at all unless you knife the gas. After letting off the gas, it goes right back to "misfiring" and the light comes back on. I can shut the car off, restart it, and it will run fine until the accelerator is pressed.
Accent MC (2006-11) :: 2007 - Misfiring Codes P0300 And P0302
My girlfriends 2007 accent as thrown codes p0300 and p0302.
After reading everything I could find, I had coil pack on my list of possible problem items.
The car sat in the driveway yesterday and when she went to start it today, she couldn't get it to.
I got it to start when I got home by giving it some gas while turning the key, but I don't want to drive it anywhere.
The hard start is leading me to believe it's the coil pack.
I was going to start with changing the pcv, spark plugs, and run fuel injector cleaner through it because those are the cheap possibilities...but now may add in a new coil pack.