Ford F-150 (2004-2008) :: 2006 - Random Crank But No Start Intermittently
I have a 2006 Ford Expedition with 95,000 miles that has a crank but intermittent no start problem. When it does happen, it will eventually start after one to two tries. I don't have to wait to start it again and I don't have any problems while it is running. Two or three times in the past two months it will sputter out and die (even though I am pressing the gas pedal) right after starting. I'll crank it again and it starts just fine. I have no problems while driving at freeway speeds or around town.
I never had any check engine lights come on so I replaced the battery and the fuel filter. I finally got two codes and replaced the fuel pump driver module and the fuel rail pressure sensor. The codes went off after replacing these two parts. I can hear my fuel pump turn on every time I start the vehicle. I have even taken the entire fuse panel apart to check Relay 303 which is soldered into the circuit board. It is fine and so is every other fuse in the panel.
Accent MC (2006-11) :: GLS Stalling At Stops / Engine Will Crank But Doesn't Turn Over Right Away
I have an automatic 2006 GLS Accent that is having a few problems. The engine will crank, but doesn't turn over right away. It might take a few tries, but will always start. This happens intermittently. Sometimes it will do it first thing in the morning, or sometimes it will happen later in the day after several start ups.
It has recently starting stalling while coming to a stop or sitting idle at a traffic light. This is also an intermittent problem. Always starts back up after a few tries.
The check engine light is not on. I have not taken it to a mechanic yet since it doesn't always do it, and will most likely be tricky to diagnose. What the problem might be? I was thinking it might be a crankshaft sensor?
Accent MC (2006-11) :: 2008 - Series Of Clicks When Turn The Key And Car Won't Start
My accent won't start anymore. When I turn the key, I hear a series of clicks, but the car won't start. When I put the key in the ignition, lights/radio/wipers all work fine. It's a 2008 manual car.
View 3 RepliesAccent LC (2000-05) :: 2004 Won't Start / No Click Or Crank When Turn The Key
I just bought a 2004 hyundai accent 1.6L standard transmission on the 13th of June, ran great drove it everyday, was driving fine when I came home monday night, went to drive it yesterday and get nothing, turn the key no click, no crank, the radio turns off as it always did when you try to start, I checked the fuses, and the battery shows twelve volts on the meter, what could cause this to abruptly happen?
View 3 RepliesAccent MC (2006-11) :: Need To Crank Twice To Start
It was the worst tonight that it has been in a while; I needed to crank the car 3 times to get it to start; mind you when it runs, it runs great.
With a bit of research, this is looking like a fuel pump/check valve problem. I have a 2010 Hyundai Accent GS, would this mean I need to replace the fuel pump assembly?
If this is the case, I want to do a beta swap over the summer. If this works out, should I upgrade the fuel pump/does the fuel pump need to be upgraded? and if so, would the upgraded pump cause other issues?
Accent MC (2006-11) :: 2010 - Random Crank And No Start
I have been having this issue randomly, sometimes it won't occur for days and other times it happens in a short period. I will place my key in the ignition, and everything will chime correctly, and when I turn over my engine, it sounds like the engine catches then it just stalls. The things I have changed so far is,
battery ( needed to be changed anyways)
spark plugs ( was set to be changed)
air filter
cabin air filter ( no relevant but still...)
oil
At first I thought it could be bad gas, since I fill up sometimes at safeways etc, but in my tank right now is 91 octane shell, I thought it could be spark plugs since I was a little over due so I changed them, and the issue never popped up for 2 more weeks, then it came back.
if I use my car starter it seems to start better, but it is maybe 1 out of 10 times it will just crank continuously without catching or anything.
I can hear my fuel pump whirl when the key is turned but not started, I checked the oil today and it is full and a light color, maybe 500 km on this oil change.
Here is the youtube issue of what is happening... [URL] ......
I rather cover most of my bases without having to bring it in for servicing.
Accent MC (2006-11) :: 2007 - Engine Will Crank But Won't Start At All
I have a Hyundai accent 2007, I guess the brain box is faulty, the engine will crank fan roll etc but won't start at all, can dis reset work for it at all ...
View 14 RepliesAccent MC (2006-11) :: Misfiring / Intermittently Kind Of Choke
Have a Accent GLS 1.6L, 92,000 miles on it the issue is what I stated above.
Basically back in March I started having issues with my car and it seemed like it was misfiring or something of the sorts at first I thought it was the IAC motor because it would only intermittently kind of "choke" if you will and it only did it while I was idling and in drive. So before I decided to go further with the IAC motor I decided to take it and have the throttle body cleaned, but it eventually started to do it again. After that I had my fuel injectors cleaned and that didn't work much at all. Kept going until a couple months ago when it actually set off a check engine light and it started doing it almost violently.
Check engine light came up with the result that coil 2 is misfiring and I went about replacing the spark plugs and the boot to one of the coils and that made the issue go away no check engine light, no nothing. Past couple days it's been doing it very very occasionally but yet still doing it.
I don't have a whole lot of cash but I need a solution quickly because this is starting to become a pain I don't want it to become so bad that I'm without a vehicle that is operating properly again.
Only thing I can note is that now it is very occasional, and when the car could be otherwise be considered "cold" and often I can't make it repeat the same thing. Had oil above cylinders when I had the plugs replaced.
Accent MC (2006-11) :: 2010 Stalling Intermittently Always When Idling
My 2010 Accent has been stalling intermittently, always when I am idling. I'll be at a stop light, and it will stall, and then it usually starts right up again. It is almost always the same stop light on my way to work, like clockwork, and likewise on my way home from work. Also, sometimes right after this stalling event, the motor will be a little rough on the highway, sputtering like it's not getting gas very well, but then it evens out after a while.
Yesterday for the first time it died and wouldn't start again. I suspected my fuel pump had gone out. I had it towed to a repair shop, but it started just fine for them and they can't re-create the problem. It doesn't give any computer codes at all.
Accent MC (2006-11) :: Hard Starting - Crank Position Sensor
2007 Accent GLS, US-market, Automatic, 140k miles
This is my wife's car. She called me from the side of the road while I was on a job out of town. The car had stalled while driving. She was able to re-start the car with check-engine lamp showing and took the car directly to a garage. It ran normally during that trip.
The garage diagnosed the problem as a failed crankshaft position sensor. They cleared all codes from the ECU without telling us what they were. My wife told them I would fix it when I got home. She drove the car home, parked it there and used my car until I got back.
When I got home, I replaced the crank position sensor with a new beck-arnley part. It was a poor fit, but it did go in. Now roughly every other start takes a few extra cranks. It always starts. It does not stall once started. No check-engine light since the initial episode. I just don't like the random hard starts.
Normal fuel consumption & power output. All other maintenance is up to date.
Accent MC (2006-11) :: 2009 Intermittently Misfiring And Burning A Lot Of Oil On Start Up
So I've been trying to get rid of the check engine light recently so I can get the car inspected. The car has about 130,000 miles. I was having problems with the car intermittently misfiring, and burning a lot of oil on start up. Also the car still had the original timing belt up until this time so I decided to change the valve seals and timing belt. I couldn't get the timing right so I took it to a mechanic and he got the car running like it was before I took it apart, although I don't think he changed the timing between the camshafts. The check engine light stayed on with p0016 as the code. The car accelerated poorly, but otherwise drove fine. I tried changing the camshaft sensor, and cleaning the OCV but that didn't work. So today I looked at the timing between the two camshafts and moved the intake cam over by one tooth which got rid of the p0016 code! Unfortunately the car decided to replace that with the p0340 code. I didn't notice any damage to the pins on the sensor. It seems to stumble for a bit after start, and when releasing the gas after revving the engine, but otherwise idles okay. I have yet to road test it.
View 4 RepliesAccent MC (2006-11) :: 2010 - Window Crank Removal From Door Panel
How to remove the window cranks from the door panels on the 2010 Accent. I have reaad lots about other models and can't find anything on the 2010. I purchased the cranks removal tool but it don't appear to work at all. I drop by my dealer and that was like talking to the wall, they don't know how to remove the handle.
View 6 RepliesAccent MC (2006-11) :: 2009 - Running Rough At Idle And Would Crank Hard / P0496 Code
Check engine light had come on, the car was running rough at idle and it would crank hard. So I threw my code scanner on it only to find out it wouldn't link. Drove it to O'Riley's and had them pull the codes. It ran rough and had next to no power on the way there. O'Riley's pulled the codes and we got a P0300 (random multiple misfire), P0301 (cylinder 1 misfire), P0302 (cylinder 2 misfire), and a P0496 (EVAP emissions system high purge flow). So once I got it back to the house, she told me that she had the codes pulled once before and that they told her it could be her gas cap so she replaced it. She also stated that she had replaced the plugs about 3 months ago.
So with new gas cap and new plugs, and these codes, I did a bit of research and come to the conclusion that it'd replace the purge solenoid. The solenoid was making a pretty loud ticking noise and when I pulled it off, it rattled so I figured that was the fix. Pulled her plugs and you can clearly see that cylinder 1 was running VERY lean and cylinder 2 was a little richer but still too lean. Plugged the plugs back into coils and laid them on exhausted. Turned the car over and we had spark. Lead me to think the misfire had something to do with the P0496 EVAP code. Put everything back together and erased the codes. Gave the car back to her and told her to let me know if the light came back on. That was Wednesday last week. Sunday she told me the light came back on and the only code that came up was the P0496 again. When I gave it back to heron Wednesday, it would still crank hard but would start.
Battery is new and checked good, alternator is pulling about 14v and checked good and the starter checked good. My dilemma is the code and the hard crank. She told me that it only cranked hard for her once so I am assuming that has gone away but we're still left with the P0496. I am not 100% sure as to how this system operates but I understand it for the most part. She told me that she had just put gas in it before the light came on. Not sure how much time had elapsed after filling it and the light coming on but I do know she put gas in it. If it's a high purge flow, that makes me think there may be a leak in the system but I'm not sure where to go from here without throwing a bunch of parts and money at it.
Ford F-150 (2004-2008) :: 2007 Truck Does Not Crank When Turn The Key To Start
I have a 2007 F-150 5.4l that does not crank when you turn the key to start. I have tried jumping the starter over and it does crank after that but it will not start. I am completely stumped by this and I'm not sure what the problem is?
View 2 RepliesSonata NF (2006-10) :: 2007 / 2.4L - No Crank When Turn The Start Key
I Have a sonata 2007 2.4L automatic and I just had a start problem today. I turned the start key and nothing no crank, all the light in the dashboard are ok, i can hear the fuel pump and my batery is fine. I tried 5 time to start it and nothing I wait 10 minutes and the car started ..
View 10 RepliesFord - Explorer :: 2006 - No Crank When Turn The Key To Run Position
My wifes explorer will not attempt to turn over. When I turn the key to the run position the dash does not do anything. I dont get any indicator lights or anything from the dash. And also the PATS light in now a steady dim light. So now I am confused and don't know where to start on this one. Is this a PATS issue or is my instrument cluster the problem? I did read the TSB on the cluster.
View 2 RepliesFord Super Duty (1999-2016) :: 2008 F250 Will Turn Over But Not Crank
I have 08 f250 6.4 was driving down the road truck just died. Will turn over but not crank. I've checked oil level, water level, fuses, fuel cut off switch. Still no start.
View 3 RepliesChevrolet - Colorado :: 2006 - Engine Will Turn Over But Not Crank / Start After 10 Minutes
Fuel Pump and Fuel Pump Relay replaced after 115,000 miles. On occasion, engine will turn over but not crank ... wait 10 minutes and the engine will start. No security light (passlock) or engine trouble codes displayed or recorded. Once the engine starts, it runs smoothly and normally. Problem of starting did not occur until the fuel pump and relay were replaced.
View 4 RepliesFord F-150 (2004-2008) :: 2006 - Won't Crank And Run - ECM Fried?
I have an 06' F-150. Last monday went to start and wouldnt crank over. I have since replaced FPDM, a weak fuel pump, checked Fuel Inertia Switch and now that they are all replaced when I check codes it says "no data available". Pump will not come on. Fuses have been checked. I have traced this problem to everything I can think of. If my ECM is fried, why would it have worked fine before replacing FPDM? I am at a dead end. Mechanic is at a dead end.
View 9 Replies