Toyota - Tacoma :: 2003 - Clutch Not All The Way Disengaged When Push The Pedal To Floor
The clutch on my 2003 Toyota Tacoma has been acting funny for a while. I have to pull the pedal back up with the top of my foot about half the time, otherwise it acts like the clutch isn't all the way disengaged when I push the pedal to the floor. The master and slave cylinders have both been replaced as well as the clutch pedal mechanism itself (thought it might be the spring). I adjusted the push rod a little bit and it seems to have worked slightly but it's definitely still a problem.
View 3 RepliesToyota - Tacoma :: 4 Cylinder 5 Speed - Sticking Clutch Pedal When Pushed To The Floor
I have a 2007 Tacoma 4 cylinder 5 speed. The clutch pedal started sticking about a month ago and has only happened a hand full of times. When the pedal is pushed to the floor it would stick, I thought it was hanging up on the floor mat at first but that was not the case. I went out to move the truck today and the pedal immediately stuck to the floor. Like usual I tapped the pedal kind of on the side to get it to release. the pedal then came back up. But now it wont push back in at all!!! There is only 1/2" of travel on the pedal and stops solid. It's like it is binding up on something. The spring seems to be in place the right way and nothing that I can see obviously wrong.
View 4 RepliesGolf IV / Jetta IV :: 2003 - Clutch Pedal Sticks To The Floor
2003 Jetta, 1.8T, 5spd, stock, 129k miles. I am working on a friends car and his complaint is the clutch pedal occasionally sticks to the floor and during this sequence it is hard to shift gears. I removed knee bolsters to inspect under the dash and found all linkage straight, all plastic parts/springs in place and no fluid leaks, I removed slave cylinder from bell housing and found smooth operation and no leaks. I guess I could replace both but I am wondering if there is a common issue. My searches have found broken plastic parts, bent push rods and leaking cylinders.
View 4 RepliesKia - Spectra :: 2004 - Clutch Progressively Sticks To The Floor
I drive a 2004 Kia spectra (base model) w/ 93k
My clutch would start out fine as I start the car, but after pressing on the clutch pedal for about 40-60 times on one trip, it'll start to loose pressure & becomes stickier. And as I press on the clutch pedal more & more, the problem gets progressively worse to the point where I have to manually pull the clutch back up with the tip of my foot.
I also notice that when I drive with the air conditioning, the problem would precipitate earlier & clutch response deteriorates much quicker. But when I let the car rest for a couple of hours or overnight, the clutch response would slowly return, and eventually be normal again.
Honda - Accord :: 2005 - Clutch Sticks To The Floor
I own a Honda Accrod 2005 V6.
I don't know much about cars, but for the past year my clutch gradually started to just stick to the floor. I'm now at 80,000 miles, the clutch doesn't slip, and it for the most part drives fine with exception to this sticking. Sometimes when this happens, the stick shift stays in gear and I can't get the stick out of gear until the clutch has been lifted up and pushed back in. It is def getting worse. I have brought it to several mechanics.
I have been told by Honda that I need to replace the clutch set (clutch disc, pressure plate, and throw out bearing) and the clutch master and slave cylinder.After another mechanics look over, they also did confirm the same as honda but stated to get a new cut flywheel.
But after several other mechanics look-overs, they told me that the clutch is fine, so they recommended me to get the master and slave cylinders replaced.
So, trying to save money a mechanic told me to take one step at a time and see how it goes. He said he will bleed the slave and master cylinders and see if it is just an air pocket. That didn't work, so I trusted him and he replaced the master cylinder, but the problem still exists. He said the next thing to do is maybe to do a new slave cylinder. I'm now contemplating.
Another mechanic took a look after the work was done and said there is no leaking.
Toyota - Camry :: 1986 - Clutch Pedal Is Going Directly To The Floor With No Effort
I have a 1986 Toyota Camry. I drove it for a year with no additional problems than when I bought it. I replaced the clutch when I bought it. However, It recently has had a new problem. The clutch pedal is going directly to the floor with no effort whatsoever. When this happened in the past it was simply out of clutch fluid, I was aware of the leak when I bought the car. Now it doesn't seem to be using any at all and I can only put it in gear when it is turned off.
I have replaced the clutch master cylinder myself and it didn't seem to solve the problem. I have tried to bleed the new master cylinder but no fluid is being drawn into the master cylinder from the fill cup on the top of it. I'm not even sure that this is the problem. I noticed that the place where the MC is attached to the clutch pedal is adjustable. Could this be a matter of adjusting this to drive the plunger inside the MC all the way forward? I am also having trouble understanding the whole clutch system. The MC doesn't seem to have anything to do with engaging or disengaging the clutch. The only thing it attaches to is the clutch pedal. Where does the clutch fluid go? Is there another place to fill Manual transmission fluid?
Ford Brakes/Suspension :: 1977 F250 - Brake Pedal Goes To The Floor And Sticks When Running
When depressed the break peddle is firm, when released break peddle does not return, replaced mc and booster, bleed breaks. Still having same problem.
View 1 RepliesPassat (B5) :: 1999 - Clutch Pedal Would Not Come Up Off The Floor / Stuck
Facts: 1999 Vw passat 1.8t
1 year ago, clutch pedal would not come up off the floor, no life in the pedal.
Problem: Clutch master cylinder, replaced.
6 months ago, clutch finally went bad. Took car to clutch shop, replaced clutch kit(found out after i payed that they only turned the dual-mass flywheel... ). Get car from clutch shop, the clutch pedal came up only 2-3 inches off the floor by itself but you could lift the pedal with your hand or foot, and it would come back up all the way, but it was life-less. It was not pulling fluid in. It was catching extremely low. I called the shop, they said that it was just because it was a new clutch and it would get better. I didn't believe them.
Two days ago, I got into my car and couldn't get it into gear. Clutch pedal would go down with the same amount of force as before. Took it back to the clutch shop and explained the history with the clutch master and then them doing the clutch kit. They said it wasn't bleeding properly and they're not sure if its going to have problems again. Car is working now, but I am concerned that it will have similar problems again.
The tech who fixed it said he pumped fluid into it extremely hard, and that's what made the pedal come up all the way (no longer stops 2 inches off the floor) and its going into gear just fine now. What the problem might have been? Block in the hydraulic lines? If this is the case, does forcing fluid through it fix it?
Passat - Volkswagen :: 1999 - Clutch Pedal Went All The Way To The Floor
My clutch pedal went all the way to the floor. The engine was missing first and then that problem happened with the clutch. I had the car towed to my business, I checked it the other day and the pedal was up. The clutch still doesn't engage.
View 6 RepliesFord Super Duty (1999-2016) :: Clutch Pedal Close To Floor?
I have a 06 f360 PSD 6 speed. On a road trip and the clutch pedal is getting very close to the floor. No Slippage but the longer I leave the pedal pressed the worse it gets. Are there any good descriptions how the clutch in this truck works?? Slave cyl??
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Clutch Pedal Would Squeak While Coming Off The Floor?
What is failing. I have a 2000 F350 PSD with 116k miles. When I bought the truck last year, I noticed that the clutch pedal would squeak while it was coming off the floor. It doesn't happen when the engine is cold. I need to drive it about 30 min before it starts to happen. On longer trips, several hours, the squeaking is louder and the pedal gets very stiff. When I stop for fuel, I've come close to stalling when coming out of 1st gear. I can push the pedal to the floor, but on the way up, the pedal squeaks, and then once I reach a certain point, say 3-4 inches off the floor, the pedal looses all freeplay. The best way for me to describe it is the pedal travels up faster than it normally does when it's cold, and if I don't compensate with more throttle at that point, it will stall.
I've learned a lot by reading this forum for the past year, but I don't know the first thing about how to diagnose problems like this. I've taken it to 2 mechanics for test rides -- one thinks the clutch is fine and thinks the problem is the slave cylinder or a broken bushing in the pedal.
The other shop is also a small independent shop, but they specialize exclusively in Ford trucks, so I thought they would be more knowledgeable. But now I'm wondering if they could sense my ignorance and are taking advantage of the situation. They also took it for a drive, but they think the slave cylinder is fine and that the clutch needs to be replaced. I questioned him about the slave, and he pulled it to look at it, and asked me to push the pedal slowly while he was under the truck. I still had a little resistance and a faint squeak even in this situation. But he said the hydraulics are so simple that he felt we could rule that out. I can't remember exactly what he said, but I think he believes one of the springs in the clutch plate has failed. I just know they are suggesting a new clutch and they want to machine the flywheel to original specs.
I thought the leading symptom of a failing clutch was slippage under a load. So under strain, I would expect my engine to race occasionally, like I'm in neutral. But I've NEVER experienced anything remotely like this, even when driving hard in the hills pulling my travel trailer.
I know something is wrong, but based on my limited knowledge, I'm not sure what. It's getting a little harder for me to move the shifter into 1st and reverse, but once it's there it's fine. I've never experienced any racing or slippage in any gear. The one definite symptom I have is that squeaky pedal that when driven for a couple of hours, gets so stiff that it can cause near stall outs. With those symptoms, what do you think is going wrong?
Ford Super Duty (1999-2016) :: F250 - Clutch Pedal Went Straight To The Floor Boards
Pulled out of street this morning and as I was shifting into 3rd my clutch pedal went straight to the floor boards. I was able to keep it in 2nd gear and get it back to my driveway . The pedal will only go straight to floor or goes straight up too the bottom of dash board. It's spring loaded. Am I dealing with a linkage issue?. I had clutch as I pulled out of my driveway and stopped go at the stop sign. Plus I was able to drive it back too my house with the pedal on the floor boards. Where I should look first?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Clutch Pedal Goes 1/3 Of Way Down - Drops To Floor And Stay?
I just bought a 99 f250 super duty with 6 speed and it has clutch problem the clutch pedal goes about 1/3 of way down then drops to the floor and stays. I pulled slave cylinder and it has just as much resistance as a new one. my other thought was a spring internally in transmission. any other thoughts or do I just need to replace the clutch?
View 2 RepliesSubaru - Outback :: 1999 - Clutch Pedal Intermittently Sticking Mid Return
So... I have a 99 Subaru Outback 5 speed that I love the hell out of. Anyway, recently my clutch pedal has started momentarily sticking mid return. The clutch appears to be fully engaged, but the pedal sticks, or hangs for a moment before popping the rest of the way up. Once, and only once so far, it stuck completely just for a moment before returning after being depressed again. I'm not sure how concerned I should be, and given that the car is new to me I'm still trying to familiarize myself with it.
View 4 RepliesFord Super Duty (1999-2016) :: 2009 F250 4x4 - Rattling When Push The Clutch Pedal To The Floor?
My stock 2009 ford f250xl 4x4 with a 5.4 and 6 speed has been giving me a weird sound lately started about a month ago and only happens on a cold start situation meaning if it sits over night it will do the sound. the sound goes away after 3-5 min of warm up in my driveway, the sound happens when i push the clutch pedal to the floor. it has no pronounced abnormal sounds through out the rest of the day when its hot which perplexes me, check out the vid on my u tube site for a sound of it.
MAH00111 - YouTube
MAH00115 - YouTube
Toyota - Tacoma :: Chains Rattling Noise Coming From Behind Passenger Seat In The Floor
I have a 2002, Toyota Tacoma, extended cab, V6, 4WD. I purchased this new back in CA, before moving to CO. When the weather turns cold, a noise begins to start. The noise appears primarily when I am decelerating (just taking my foot off the gas). The noise sounds like chains rattling. I would equate the noise to the sound a diesel pickup makes (low rumble). The noise sounds (to me) like its coming from behind the passenger's seat in the floor. The noise is quite loud (people walking on the street can hear it and its apparent something is not right with the truck). The only constant thing is that it must be cold out. So, when spring comes, I tend to forget about the issue. We are having snow this weekend in Denver and its starting again. I have taken this to multiple mechanics over the years. They tighten everything up, but cannot seem to find or fix the problem.
View 3 RepliesToyota - Tacoma :: 1989 - Won't Start Up And Intermittently Dies - CEL Comes On
I have driven small Toyota 4X4 pickups since 1980 including an '89 for the past 25 years and > 200,000 miles. One day a couple of months ago it would crank but would not start although battery and starter seem fine. I did some basic testing eventually measuring the ignition coil resistance (within published range) and inspecting the distributor cap (looked fine). Upon reassembly, it started right up and ran fine for a few weeks. I hadn't really done anything beside cleaning the rotor and cap contacts, moving around the wiring while in the process.
A few weeks ago I was driving in traffic just a few miles from home and it momentarily lost power twice within a mile. Check engine light was noted the second time. I was busy watching the cars ahead of me the first time. Both times it resumed running on it's own and I continued on. A couple of weeks later it died three times within a few miles from home.
The first two times I was able to pull off out of traffic. Several minutes later, I was able to restart the engine. The third time I was stuck in a turn lane at an intersection, police arrived right away and the vehicle was towed to the dealer where I had purchased it only two miles away. They have been unable to reproduce the problem but believe they have eliminated the fuel filter and fuel pump as the cause. They have driven the vehicle several miles and left it running for an hour and a half with no problems noted. No diagnostic codes were recovered.
They now want me to retrieve the undiagnosed, unrepaired vehicle. We know it will fail again, probably under the worst possible circumstances. In heavy traffic, a multi-vehicle crash with associated injuries or deaths could result. It's like if the vehicle itself doesn't tell them what to do, they don't know how to approach such a problem on their own any more. I'm not in a position to pour unlimited funds into a vehicle I have recently replaced (with a 2014 Tacoma). There must be a logical approach beyond checking the fuel filter and pump but they seem clueless. I can't safely drive the vehicle and won't offer it for sale until the problem is identified and corrected.
Toyota - Tacoma :: Won't Start At Cold - Crank Intermittently
I have a Toyota Tacoma 4 wheel drive it has a v6 motor. here is whats going on...sometimes it starts just fine,other times i think when it gets cold i try and start it.... it will crank over just fine but does not start, then i turn the key off and try and start it again and it starts just fine,sometimes when its acting up i try starting it and after trying to start it after 3 tries ir runs rough for just a sec or too.
View 1 RepliesToyota - Tacoma :: 1990 Transmission Won't Shift Into 1st When Clutch Depressed
So, I bought the truck used and everything about this truck is great minus the shifting difficulties in first. With the truck at a dead stop, the clutch depressed, and the shifter in neutral it can be near impossible to shift into 1st (it's possible with a lot - emphasis on a lot - of force). No grinding, clashing, knocking in the shift knob - it just wont go into gear. I can shift into 2nd-5th and reverse without too much difficulty. If the truck is in motion, once the vehicle gets between 2-5mph I can easily downshift into 1st. However, if I shift out of 1st and let the truck sit for, say, 5 seconds it is often very challenging to get the truck back into 1st.
I have tried to look up this problem online with limited success. What I found was it could be caused by:- something wrong with the clutch installation- a need to bleed the clutch (it's hydraulic and, although the reservoir is full, the fluid is a bit dirty)- perhaps a faulty clutch master cylinder- play in the clutch linkage- a broken spring in the pressure plate- a bearing that is starting to go out- worn synchros in 1st.
I am a machinist, not a mechanic, so it's hard for me to evaluate these ideas (beyond the cost associated with each). Given my limited knowledge of transmissions and my good mechanic friend's opinion, I think it's a broken spring in the pressure plate.
1990 Toyota Pickup 4x4 manual transmission. This is the original transmission in the truck, it has not been rebuilt (but has been maintained with regular fluid changes), and has a tad over 158,000 miles on it.