Subaru - Legacy :: 1993 - Automatic Transmission Won't Reverse
Reverse stopped working after it's been driven for a while. It works when it's cold. I'm actually hoping this was caused by my stupidity (though it may have nothing to do with the problem). A while ago I wanted to change my oil, but opened the auto transmission plug instead. I decided to put new trans. fluid in it. I thought I would add trans fluid until I could see it on the dip stick. After the problem with reverse started I tried to again read dip stick but can't tell where the level is, so I decided to drain trans. fluid to measure it. Owner's Manual calls for 8.8 qts. Drained fluid measured only about 4 qts. I added more. Now it looks like dipstick shows it ~2 inches above the full/hot mark. Questions:
1) Would fluid level affect reverse and not forward (with which there is no problem)?
2) Is method of draining trans. fluid & measuring it a valid way of telling how much is in it, i.e. would all... or most... fluid drain out so the 8.8 qts. in the owner's manual should be added back in?
3) Am I misreading the dipstick? I've tried letting it set for 4 or 5 days, but still fluid seems to smear high on the dipstick.
Subaru - Legacy :: 2002 - Automatic Transmission Whining Noise
My 02 Legacy with 185k suddenly developed a whining noise I believe from the transmission. The noise coincides with engine rpm. The noise lessens when the load is taken off the transmission when at cruising speed. The trans shifts perfect and the fluid doesn't look too bad.
View 2 RepliesSubaru - Legacy :: Awful Smell / Leakage And Slippage - 2007 Automatic Car With Push To Manual Transmission
I have a legacy. Notice some slippage between 2nd and 3rd and 3rd and 4th. Also noticing an extreme burning smell when vehicle first gets started (for about 15 min) it's gagging it's so strong and pours in through defrost but can be smelled standing outside car also. Finally I parked in friends garage and notice some dark weird colored fluid on ground when I backed out, I dont know if it's oil or transmission fluid.
View 1 RepliesFord Super Duty (1999-2016) :: Transmission Would Not Work In Tow Mode And Caused Engine To Go Into Limp Mode
I have a 2008 F350 with a 6.4 Powerstroke diesel engine that just experienced total engine failure. It has around 65K miles.
There is a heavy burn star pattern on all 8 pistons, a few pistons are cracked, a few cylinder walls are scored, glow plugs are melted, both heads are cracked with multiple stress fractures in each head.
About 1 month previously, the transmission would not work in tow mode and caused the engine to go into limp home mode. The dealership just replaced the entire tranny as a warranty item. About 1 week before the engine failure, I put in a 5.25 oz bottle of Lucas injector cleaner with a full tank of gas.
The Ford dealership is saying that the star pattern on all 8 pistons is due to high pressure fuel overspray and is evidence that I had a tuner on this engine and that the warranty is invalid. I did not have a tuner. What might have caused this engine failure?
Also, they only ripped down the top half of the motor, not the bottom half. I heard this might have been caused by a cracked crank shaft, but Ford refuses to investigate this possibility.
Subaru - Legacy :: When In Automatic Car Will Randomly Downshift Only On Left Turns
My 2015 Subaru Legacy will randomly downshift, when in Automatic, only on LEFT turns! The dealership says there is a sensor that is "overly sensitive" but now it is a safety concern when pulling out into traffic. I never know if it will occur. Most of the time it will shift back into automatic on its own but there have been times where i have had to use the shifter paddles to shift up then it will kick back into automatic. It only has 31,000 miles, bought it used with 18,000 miles. I have also noticed if I don't accelerate slowly, it seems slow to shift automatically and reduce RPM's. I don't want 36,000 mile warranty to bypass without this resolved.
View 19 RepliesSubaru - Outback :: Limp Mode After Replacing Drive Shaft
I have a 2005 Subaru Outback 2.5 and a while back I had to replace a drive shaft. After replacing it my car goes into limp mode and I get a different random code every time. The car seems to run fine when it is cold but after it warms up it will go into limp mode randomly. If I cost to a stop and shut down the car and wait a while to restart it runs fine. I've tried and researched just about everything thing.
View 6 RepliesSubaru - Outback :: 2005 - Big Boost Upon Acceleration At Stoplights / Limp Mode
I have been battling a big boost upon acceleration at stoplights for approximately 6 months. Now twice I have gone into limp mode and the tech reads: PO700 (Transmission) and PO731 (Gear 1). I just turned over 190,000 miles but only purchased it a year ago. What is the problem(s)?
View 1 RepliesGolf IV / Jetta IV :: Transmission Going Into Limp Mode
My Jetta mkiv transmission went into limp mode recently. Took it into shop. They checked it out and they replaced solenoids as well as the TCU. Car still goes into limp mode. It doesn't happen all the time but enough to piss me off. Any thoughts?? Car only has 140000 miles.
View 1 RepliesRodeo :: 2000 Transmission Stuck In Limp Mode?
My tranny is stuck in limp mode. I can manually shift it, but it won't shift on it's own. The 'automatic' part of the automatic transimission is definitely not working right.
I searched and checked for the usual suspects, low battery or alternator output (measured over 14v at batt. when on), and the range selector switch. I removed the switch, took it apart, cleaned it up, and reinstalled it. It looked like it was in decent shape inside, although it appeared to have had a bit of oil of some sort that had leaked into it. There was a bit of oil on that side of the tranny, around the gear selector and switch, but not enough to actually drip as I don't have any stains on my driveway where I always park. The only thing I haven't checked is the atf fluid level, as I can't seem to find the my wrench that will take off the fill nut. I'll get that figured out tonight.
The tranny hasn't been taken care of like it should, I've had the fluid replaced two or three times over 100k of ownership, but I'm not sure about the filter. Would the need for a filter and fluid change cause it to go into limp mode? Also, it's not throwing any CEL codes either.
Touareg :: 2007 Transmission In Limp Mode - Car Lurches
33K and no problems until this morning. Wife gets 400 yards down the street, car "lurches" and goes into limp mode. Transmission won't shift out of whatever gear its stuck in (going forward) Car will back up. Only indication of any possible trouble is occasionally the very first time the transmission shifts in the morning from 1st into 2nd its a little spirited rather than silky smooth.
View 5 RepliesPhaeton :: Transmission Control Module Resulting The Car Being In Limp Mode
My transmission control module has gone bad, resulting in the car being in"limp" mode. I am advised not to drive the car in this condition as it starts out in 3rd and the transmission will be damaged. Thus far, my local dealer has, on a preliminary basis, been advised that there are none of these parts available anywhere in the world according to the computer and VW may have to manufacture one. This does not sound possible. Meanwhile, the dealer says no rental car will be offered so I am contacting VW North America to escalate. It could be up to a month to get a new part. Meanwhile, the car is in the garage just sitting.
View 7 RepliesAccent LC (2000-05) :: Transmission Limp Mode / Stuck In 3rd Gear
So yesterday, this had happened for the third time in 3 years owning this car. Unhooking the battery for 20-30 minutes resets the computer and it is ready to go for a while with no issues. This has become annoying though. What is causing the car to enter "limp" mode and stay in third gear? One time it happened, I brought it to AutoZone and they did a scan and came up with the speed sensor. I haven't replaced it because it didn't happen for a while after that.
View 11 RepliesFord Ranger / B-Series :: Transmission Goes Into Limp Mode When AC Turned On
Turn air conditioner on transmission goes into limp mode??
1999 ranger 2 door 2,5 engine long wheel base,,auto trans.
2wd no power windows no power seats....
Santa Fe (CM - 2007-12) :: 2008 Limp Mode - CEL / ESC And AWD Transmission Lights Blinking
I'm a little bit stuck here. This happened last night, and the dealer is closed today. I have a 2008 Santa Fe SE. It stalled last night, and when I turned it back on, I got a check engine light, the ESC light, and the AWD transmission light blinking. When I go to accelerate, it will not go passed 2000 RPM, and it is driving very sluggish. Its not knocking, or making any other kind of sounds. The air conditioning does not work, but the fan blows uncooled air. It accelerates extremely slowly, even with the petal mashed.
I plan on taking it in tomorrow, but I'd like to know if there is some way to reset the computer. I tried disconnecting the battery for about 30 minutes, but it didn't work.
Chevrolet - 1500 :: 1992 - Transmission Suddenly Hit Limp Home Mode
I have a 1992 1500K extended cab 4WD with the 5.7L V8 engine (147,000 miles). It has been driving well since I bought it last winter. 2 days ago I took it on a longer road trip and it was doing great. Slowed down to take a 90 degree turn and the transmission suddenly hit "limp home" mode. It felt like it wasn't up-shifting out of 2nd , high RPMs while driving no more than 30mph on flat road. I have the proper amount of fluid and it is still red/pink and does not smell burnt.
Someone suggested that I check the transmission fuse but in looking through the fuse box I can't tell which is the tranny fuse. Also, I can only find one fuse box on my truck. Is there a 2nd?I feel like my next step is to take it to a transmission shop but I want to rule out whatever I can at home. I have zero experience with transmission work and don't want to get scammed into a rebuild if I don't need one. The transmission was working fine up until 2 days ago. No slipping, no hard shifting, and no noise...
Ford Ranger / B-Series :: Transmission Went Into Limp Mode With O/D Light Flashing
2001 Ranger 3.0 liter has developed a transmission casualty. I was driving along at 30 mph and the transmission went into "limp' mode with O/D light flashing and truck will only barely creep along with high engine rpm. When I got the truck home I was able to retrieve a p0720, output shaft speed sensor signal fault. I had hoped that replacing the sensor would solve this casualty.
Of course this was not the case. I have read all the posts I can find for this particular fault and realize that I must electrically trace the continuity of this circuit and also ensure that it's not grounded. I have been unable to find the needed wiring diagrams or pin out information.
Before I have to try and blindly start pawing through the connectors I'm looking for the pinout for the PCM and perhaps the bulk connector above the engine between the PCM and the transmission wiring harness. I am also keen to hear of any diagnostic tips that I may have overlooked.
Ford Transmission :: 1993 F250 E4od Limp Mode But No Codes
Alrighty now. I have a 93 f250 idi Na.
Before problems started: the truck.shifted all 4 gears fine.
Problem(s) begins: Then out of the blue(after I shut it off... even if it was for 30sec, and then turn it on ) it would go into limp mode but if I shut it off and then turn it on again, it would work fine. After about 3weeks/ 600 miles it just went straight to limp mode.
What I did: After 3-4 weeks of that, I replaced the solenoid pack(uncooked both batteries and waited 10 min before I hooked them up) with a eBay special. After that, I had 1st,....., limp 3rd, then it'd slam like check into OD. To get second(which was limp), I'd have to manually drop it in 2 and and let off the pedal before I'd put it in D, to avoid it slamming straight into OD. It would toy with limp and OD from 35mph-45mph. Then it.just went straight to limp mode again.
What I couldn't do because don't know how to solve: I went to go get the codes read and the connector was missing and only one wire was leading to where the connector should've been.
What I did...again: I replaced the control module in the firewall. Then my codes cleared up. And same problem as when I put the new solenoid pack in. But no codes.
What is it still doing????: it's a go round battle between complete limp mode, limp mode and wanting to go into gear(suited to proper mph&rpm), or 1st, limp2&3, and OD.
What I tried: TC lock-up switch.,. And it worked but didn't solve my problem so I scratched that one.
Santa FE SM (2001-06) :: Transmission Started Going Into Limp Mode And Causing Check Engine Light To Come On
2002 Santa Fe, 2.7 AWD
The transmission has started going into limp mode and causing the check engine light to come on.
The codes given are p0750 and.... I think p0751, for shift solenoids C and D. There is also the generic Transmission Control Module code.
Limp mode only occurs at higher speeds although shifting feels a little rough at times in lower speeds.
If operated in manual mode the vehicle can be driven normally at all speeds without going into limp mode.
Fluid levels are fine.
With limp mode occurring in automatic but not occurring in manual mode, is it more reasonable to believe the solenoids are malfunctioning or the control module itself? I'm inclined to replace the solenoids but find it odd that the vehicle operates normally in manual. Also, can the solenoids be replaced without removing the transmission? It looks like I could get the pan off but am unsure if there is room to get the work done once it is removed.
Santa FE SM (2001-06) :: 2005 - Transmission Shifting Poorly And Getting Stuck In Limp Mode Intermittently
I have a 2005 2.7L Santa Fe that was shifting poorly and getting stuck in limp mode intermittently. I read up on it and found that it was probably an issue with the input/output speed sensors. The codes confirmed my suspicions and I replaced both the input and output sensors. The codes cleared and the tranny shifted like a dream. Unfortunately after 2 days and 100+ miles the car suddenly started down shifting randomly on my way home from work. The CEL came back on and the car went into limp mode. Could the sensor have gone bad again? Or could it be the wiring harness that plugs into one of the sensors? I don't understand why the car would be fine for a few days and then all of a sudden be acting the same way.
View 6 Replies