Sebring - Chrysler :: 2001 - Shakes And Jerks / CEL Came On?
My daughter's 2001 Chrysler Sebring began "shaking and jerking" last night. She described it as similar to when a person drives a standard transmission that doesn't know how to do so. (Her car is an automatic.) She had been driving it for about ten minutes without a problem and had luckily just turned onto a residential street to pick up a friend. She said the check engine light came on as well. She was able to limp it to her friend's and leave it parked there.
Recent work on the car includes the thermostat being replaced and a resistor related to the heater blower motor being replaced. What might be causing this. She's probably going to have to have it towed.
Volvo :: Vehicle Shakes Badly When Braking
I have a 95 940 turbo that shakes really bad when braking. things I have done so far are.
1. Replaced all four rotors.
2. Replaced all four callipers.
3. Replaced sway bar control arms.
The shaking is so bad that the gear shift moves back and forth when braking.
Brakes - Jetta - Volkswagen :: 2001 - Shakes Badly While Braking?
I have a 2001 vw Jetta with a manual transmission (just over 155,000 miles). My first set of front brakes lasted to about 135,000. After they were replaced a shimmy started to appear when braking a few thousand miles in. At about 8,000 miles the shimmy became so bad that I brought the car back to the dealer. They said the rotors were warped. The pads and rotors were replaced again and in about 5,000 miles same thing. The pads and rotors were replaced again at no charge and it is now about 5,000 miles later and the same thing is happening again.
View 2 RepliesChrysler - Sebring :: 2002 - Engine Is Blown?
I have a 2002 Chrysler Sebring that broke down. Unfortunately it ran out of oil, and I was told that the car has 2 sensors that detected the lack of oil and shut down the engine. A local auto repair shop replaced the sensors. I paid the bill and began to drive the car home but I only got 20 miles away when the engine blew. My question is, if the the shop told me the car was fixed and then the engine blew, aren't they somehow liable for this?
View 19 RepliesChrysler - Sebring :: 2002 - Check Engine Light Came Driving Down The Highway At About 70 MPH
I drive a 2002 Chrysler Sebring convertible with about 130,000 miles on it.
I was driving down the highway in early November when the check engine light came on my car. I took it to Aamco who did some diagnosis and replaced a solenoid assembly in the transmission. The light went off and I was on my way. I never got the exact code.
About a month after that, the light came on again. This time, I got a low end code reader and scanned it myself. I got a "P0700" code, which I've read is a generic code that the transmission system sends to the computer or something. So I used my reader to erase it. However, the light came on 2 days later while I was driving down the highway at about 70 MPH.
So I went to an auto parts store to get a more detailed scan with a better tool. This one came up "P0740 Torque Converter Clutch Solenoid Circuit".
This feels weird, because the solenoid assembly was just replaced a month ago (and is still under warranty).
The car seems to drive okay. I don't notice any actual problems in shifting. The tachometer seemed to get up to about 3000 RPM on the highway. But I've seen practically new cars do that. The last time I had serious transmission problem it would rev up to about 5000 or 6000 RPM on the highway and still only getting up to about 40 MPH. That was 3 years ago and at the time I had a fairly expensive transmission repair (which included a new torque converter).
But like I said, the car seems to be driving okay. I don't drive much. Maybe 100 miles a week? And even that is mostly optional in town driving. I'm not looking to keep this car for more than another 20,000 to 25,000 miles though for the time being I cannot afford a new one.
What are the possible causes here? What are the consequences of ignoring this? Like I said, it's still driving fine and as the old saying goes "if it's not broke, don't fix it".
Chrysler - Sebring :: 2002 - Engine Start After About 5 - 10 Seconds Of Cranking When Cold
I recently bought an 02 Chrysler sebring (4 cyl) When cold, it takes about 5-10 secs of cranking for engine to start. Is that normal?
View 4 RepliesSebring - Chrysler :: 2002 - CEL Came On - Camshaft Position Sensor - Hard Starting?
Check engine light came on and off for a couple of months. At first engine would lug at about 35 mph then light would come on, then off, usually by next start. Car stalled once when sitting at light, then light came on. Scanner said it was the Camshaft Position Sensor. Replaced it and now I need to give it gas first thing in the morning and in the evening after it's been sitting a work all day. Why it's doing this?
View 6 RepliesSebring - Chrysler :: 2002 - Engine Shut Off While Driving / Apparent Grinding Noise
I have a 2002 Chrysler Sebring with 116,000 miles and over the past month the engine has shutoff as I am driving and once I park turn the key off and turn on it has started to run again. This has happened about four times and each time it has been difficult starting it after the car has stalled. The most recent time this happened when I went to restart the car, a grinding noise became apparent. The last few times that I have started the car the grinding noise would be heard only to ultimately fade away in about 15 seconds. The check engine light came on and went to get the code and it came back suggesting a problem with the camshaft position sensor, but I don't fee the noise is related to that.
View 1 RepliesFord Excursion :: 2002 - Steering Wheel Shakes When Braking
My question is I have a 2002 Excursion 5.4 2wd with 126K on it, I have been chasing a shaking steering wheel while braking at higher speeds 50 mph and up, it is stronger at higher speeds and gets weaker and eventually goes away when slowing under 45ish mph. The shake in the wheel does not pull the truck at all, you can let go and it still stops straight. I have aligned and balanced I know its right I did it myself. I have also replaced steering dampener, and have done a full brake job on the front all new parts everything. Also the steering linkage is tight no slop or play in it.
View 14 RepliesPassat (B5) :: Steering Shakes Badly?
I took the car in for a steering vibration/jiggle problem (and a 60K mi service), and the dealer replaced the axles/driveshafts under the powertrain warranty.
It seemed fine when I drove back home, but recently I've been noticing the steering shake again. If I remove my hands from the wheel, it jiggles and pulses to the left and right by itself. Whenever I turn the wheel off center left and right, (while moving; mini-slaloming, I suppose) the wheel resistance pulses back and forth... it isn't creamy smooth. And finally on the freeway, the front end seems to hop... it's rather disconcerting.
Can any of this be cured by the powertrain warranty... or am I looking at some suspension/steering work?
Passat (B6) :: Engine Shakes Badly And The RPM Keeps Bouncing
Ok so here's the thing. I put an intake on the car. But the engine shakes badly and the RPM keeps bouncing. There is no air leak. Is there any vag-com programming that needs to be done for the intake to work since it is going to be different than the stock one? t is a 2.0t engine.
View 11 RepliesChevy - Silverado :: 1999 - Shakes Badly At Several Speeds
I have a '99 Silverado 1500 with a 4.3L V-6 amd 188,000. It picked up a problem recently that's been stumping me. Occassionally, and for no reason I can sort out, it starts to shimmy badly. This behavior has come about at several speeds. Sometimes just cruising down the road at 35-45 it starts to shimmy and wobble and the steering wheel shakes as if a wheel is horribly out of balance. Other times this occurs at highway speeds - it's noticeable and alarming. The problem can last a long while; othertimes the symptoms disappear in a few seconds. The first time it happened I thought I had a flat or was about to lose a wheel - this is not a subtle problem.
I've checked several things and came up empty. No delamination in the tires and nothing out of round, but just to be sure I had the wheels balanced and rotated - the balance was spot on when checked. Alignment is good. Did those things, but the symptoms continued. The vehicle is high mileage so I put in on the lift and checked the front-end. The steering rack has a very slight amount of play and the hub bearings have a very small amount of play too - I'll get after those, but they're not causing this intermittent problem. Everything else is tight. Shocks are fine, brakes are fine, I checked the rear-end as well - everything is straight and true. Air pressure is set correctly. I checked the driveshaft for runout and play - that's not the problem. The truck has never been in an accident and nothing seems misaligned.
The truck drives like a new truck most of the time, then suddenly, on a smooth road, it starts wobbling around. I'm starting to believe the problem might lie under the hood. I had a problem some time back with misfiring and the truck bucking - this turned out to be a worn distributor. A new distributor, rotor and wiring solved that problem. But these symptoms are not similar - this is not a bucking problem; the entire vehicle starts to shimmy and wobble with the steering wheel vibrating back and forth. It's hard to tell, but I cannot detect any misfiring or rough running in the engine when these symptoms appear and I have no 'check engine' warnings.
Are there any engine/transmission/drivetrain related issues that could cause intermittent symptoms that feel like an out of balance condition? A few other facts:- I have noticed the truck is a little down on power lately- The fuel economy has dropped off - I used to do around 20, now I'm down to 16mph highway- (Very) slightly rough idle
Gmc - Sonoma :: 1996 - Engine Shakes Badly And Struggles To Run / Timing Is Way Off
I have a 1996 GMC Sonoma extended cab, 2.2l engine (not vortec) purchased in the United States. I’m having trouble setting the timing correctly.
I recently replaced the camshaft and crankshaft sprockets and chain, and after several attempts to set the timing, the engine still shakes badly and struggles to run smoothly, especially at idle. (It did not do this before the repair.) My code reader picks up the following codes: P0106, P0108. It seems to me that the timing is off despite my best efforts.
I’m going to try and attach a picture of the timing chain and sprockets as they’re currently set because the camshaft timing mark is strange on this vehicle and I’m not sure if it’s lined up correctly. Does it looks right? (Red mark on cam sprocket made by me; timing mark is supposedly the circular hole above that tooth.)
I did several other repairs at the same time that I did the timing. I have gone back over as much of these as possible and I don’t think I did anything wrong. As cars go I’m strictly an amateur but I work as a small engine mechanic so I have some experience with the way things feel when they’re done wrong. Nevertheless, if the timing is right, maybe I botched one of these?
The simultaneous repairs:
Removed head
Replaced hydraulic lifters
Cleaned carbon off valves
Checked pushrod straightness
Changed gaskets (several)
Replaced oil pressure sensor, coolant temp sensor, & thermostat
Replaced coolant hoses
I did all this because I hit the 150,000-mile mark and I want to keep it running for another 150,000.
Chrysler - Sebring :: 2004 - Transmission Will Not Go Into Reverse
I have a 2004 Chrysler Sebring with a 2.4L dohc and automatic transmission with 115k miles. I recently had the timing belt and water pump replaced. Shop left the front 2 engine mounting bolts off and the rear one loose. Picked up car after business hours drove it that evening and kept hearing a strange metallic squeak.Returned it to the shop the next morning and as i was driving it began to smoke and stall with the temp gauge pegged. They had also left a hose to the heater core disconnected. Could the engine not being mounted to the chassis and/ or the overheating have damaged the transmission.
View 3 RepliesSebring - Chrysler :: Heater Blowing Cold Air
Got a bit of a problem with my car. Earlier this week, I got in and noticed there was heavy condensation on the inside of the windshield of my 2002 Chrysler Sebring convertible. The windows had been rolled up and the top up of course. I see this kind of condensation happen on the outside a lot in the mornings. You know, dew settling and all that. If I wait around until later in the day, it evaporates on its own.
Anyway, this time it was on the INSIDE. I wiped it clean easily enough and was on my way.
Today I noticed that my heater wasn't working. The temperature gauge goes up to about 1/3 of the way, so I know the car is warming up. I'm not sure if it normally goes up that high; I don't usually pay much attention to the temperature gauge.
Chrysler - Sebring :: 2006 - When Stopped With AC On Car Tends To Surge
I have an '06 Sebring convertible, 2.7l, V-6, 58,000 miles. When stopped with A/C on, car tends to surge. When I put in neutral, surging stops. Also, I sometimes get a "thump" (with both sound and feel) like I've been rear-ended, but have not. Dealer did tranny serivce and replaced all plugs and 2 coils which they said were "arcing". Did not fix problem. What would be wrong with A/C so as to cause this?
View 5 RepliesSebring - Chrysler :: 2000 - Quit While Driving
2000 Chrysler Sebring Convt quit while driving. Tow truck drive and a mechanic at scene of breakdown felt itt seemed like it wasn't getting gas. Replaced fuel pump, fuel filter, 2 sets of plugs ans it won't start and when it did it ran rough and then fouled out new set of plugs. Seemed like too much fuel going to cylinder.
View 1 RepliesSebring - Chrysler :: Oil Light Comes On When Stop But Goes Off When Driving
My oil light comes on when I stop but goes off when I'm driving. I check the oil level and it was fine. What would cause this? It's a 2001 sebring 2.7L
View 6 RepliesChrysler - Sebring :: Alarm Was Going Off At Random Times
I recently brought my 2000 chrysler sebring in because the alarm was going off at random times (3:00am). Also when I was driving the interior lights would turn on and off and the dash readout would say "DOOR" as if I had opened the door, there was a relay clicking sound under the dash and the car would also try to relock the doors. This was an intermittent problem, occasionally the car would be fine for a while then the show would begin. I took it to a local Chrysler dealer and they diagnosed the problem to be the BCM or Body Control Module.
My conclusion is that this whole problem was caused by a shorting door switch and that either they misdiagnosed the problem and when the new BCM did not fix the problem they found the real problem in the door switch or they just scammed me from the start. I think the "part exchange program" is a scam. Why don't I get the part back or why don't I get two prices, one if I exchange the part and one if I don't.
Could a faulty driver door switch damage a BCM? (I never heard of this before. In fact another dealer told me all he needed was the VIN to see if the part was in stock).