Ford - Explorer :: 2002 - Chirping Noise When Starting From Cold / Camshaft Position Sensor Location
Have a 2002 Ford Explorer 4.0 6cyl. w/ around 150K
I recently started hearing a little chirping noise when starting from cold. The rate of the chirping increases with the rpms (reving in neutral or when speeding up while driving). The sound usually goes away after things warm up.
Doing some research, the most suggested cause for such chirping is something called a Camshaft Position Sensor. Information mentions that this item can either need lubrication or to be replaced.
I was going to try lubrication first....then if the problem persists...replace.
My biggest issue is locating it on a 2002 4.0 Explorer (4 door, 4wd). I've read different reports for different Year models (mostly 97-2001)...which often include pictures. But I can't find ANY pictures for the 2002 4.0
QUESTION: Where it is located on my 2002 6cyl model? I read one account of it being on top of the driver's side valve cover....and I DO see an item in that location secured by one bolt..and it does have an electrical wiring harness attached....but I'm not sure...and have not seen any photos that look like my engine.
I've attempted to upload a picture of what I think maybe be the sensor (circled on red).
I've also come across an item called a "CRANKshaft position sensor".....are these different items, and, if so, does the crankshaft p.s. also "chirp" when needing lubrication or replacing ?
Camry :: Toyota 2002 LE 2.4L - Code P1379 Camshaft Position Sensor
The computer is returning P1379 camshaft position sensor. Where is this sensor located on a 2002 Toyota Camry 2.4L and how easy would you rate the job of replacing it?
View 3 RepliesFord F-150 - 1997-2003 :: 2002 V8 - Camshaft Position Sensor Harness
Just bought a 2002 4.6 v8. Check engine light was on and it pulls code po340 for the camshaft position sensor. I took a look at it and found its not plugged up. The plug is missing but the two wires are still there. I can replace the two wire plug but does it matter which wire goes to which side of the sensor?
View 3 RepliesAccent MC (2006-11) :: Hard Starting - Crank Position Sensor
2007 Accent GLS, US-market, Automatic, 140k miles
This is my wife's car. She called me from the side of the road while I was on a job out of town. The car had stalled while driving. She was able to re-start the car with check-engine lamp showing and took the car directly to a garage. It ran normally during that trip.
The garage diagnosed the problem as a failed crankshaft position sensor. They cleared all codes from the ECU without telling us what they were. My wife told them I would fix it when I got home. She drove the car home, parked it there and used my car until I got back.
When I got home, I replaced the crank position sensor with a new beck-arnley part. It was a poor fit, but it did go in. Now roughly every other start takes a few extra cranks. It always starts. It does not stall once started. No check-engine light since the initial episode. I just don't like the random hard starts.
Normal fuel consumption & power output. All other maintenance is up to date.
Golf/GTI VI :: Camshaft Position Sensor Oil Leak
Wasn't there a TSB for this? I've searched Google and Vortex with nothing for the MKVI but I could swear I read something on this.
I am accumulating oil/grim right around the sensor and it's beginning to irritate me. I want to take her to the dealer but would rather know for sure of any possible TSB out there so I have something to reference.
GTI 337/20th Anniversary :: Where Camshaft Position Sensor Located Under The Hood
The CEL just came on in my 20th AE Gti. The code indicates a Camshaft Position Sensor issue. Don't know where this sensor lives under the hood of the GTI? Is an easy enough fix for a beginner to attempt? (have hand tools, former bike mechanic, but no shop just a parking lot in the Texas sun!)
View 6 RepliesAccent LC (2000-05) :: Camshaft Position Sensor Code P0342
So my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 RepliesAccent LC (2000-05) :: Camshaft Position Sensor - Circuit Low Input
My 1.5L 2000 Hyundai accent is reading p0342 code.(cmp sensor circuit low Input). I have changed out the sensor from a parts car and it's still reading this code. I've read it could be timing or an issue with the starter wiring.
View 3 RepliesElantra XD (2001-06) :: 2003 - CEL Code / Bad Camshaft Position Sensor
I am new to Hyundai. I just picked up a 2003 Elantra and I'm doing a couple fixes to it. When I got it, the engine light was on and the code displayed said it had a bad camshaft position sensor. Is this a common issue with the car and is it an easy fix?
Also, I just installed new brake pads and a new battery. Now the battery and brake lights are on, although I know I didn't break anything. Could installing a new battery cause the two lights to come on?
Accent LC (2000-05) :: Code P0342 - Camshaft Position Sensor
My daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 RepliesSonata NF (2006-10) :: Camshaft Position Sensor Location On 2007 GLS
I have been getting a P0011 error code. Changed the OCV but the code continues. I'm going to try replacing the CMPS but am not quite sure of the location on the 2007 Sonata GLS. Looking for any pics of the location or a description?
View 1 RepliesMazda - Protege :: 2003 - Camshaft Position Sensor Location?
Where the camshaft position sensor is on a Mazda Protege5 2003. I can't seem to find any information about this particular car.
View 2 RepliesFord Ranger / B-Series :: Camshaft Position Sensor On 1996 2.3L
My check engine light came on about a week ago and was unsure what the problem was. So I tested the codes and it said that the camshaft position sensor was bad. So I have tried finding this sensor but little to no luck. I was unsure if it was the 2 or 3 pin, but after looking at some pictures of the engine I'm thinking it is a 2 pin. I attached two pictures of what I think might be the sensor? But I am unsure. This was right next to the timing belt cover, which is where it said it was located. I have a 1996 Ford Ranger, 2.3L.
View 6 RepliesCelica :: 1997 7afe 1.8 ST - P0340 Code For Camshaft Position Sensor
I am getting the code for the camshaft position sensor. Erase code, comes back immediately. I don't even think this car has a camshaft position sensor.. I guess the first step would be locating the little bugger. Crankshaft position sensor is new and seems to work fine. Car is running btw.
View 5 RepliesJimmy :: 95 Running Rough / Stuttering - Camshaft Position Sensor Code
I have replaced the camshaft pos sensor multiple times from Autozone (warranty ) and replaced with one from Advance Auto still get cam sensor code changed crankshaft sensor today still running like crap, stuttering. I have also done a complete tune up and the Distributor has not been pulled.
View 1 RepliesGolf IV / Jetta IV :: CEL On With Camshaft Position Sensor Code And Misfire On Cylinder 3
She is a 1999.5 Golf 2.0 (although, she just has a rabbit symbol on the hatch, is she a Rabbit or did someone remove the Golf badge?) I just bought the car, with less than 160,000 miles. The dome lights work sometimes, Door Ding works intermittently as well, but sometimes will "glitch" in other words it will be making the sound but it kind of stutters? Odd? The horn sometimes works, however it is very silent? Check engine light is on with a camshaft position sensor code and miss on cylinder 3. Someone told me to replace the "109 relay"... could this be the problem or is this the CCM?
View 5 RepliesGolf IV / Jetta IV :: 2004 - Camshaft Position Sensor Error Code
I have a 2004 MK4 Golf 2.0l that's been throwing a CPS error code. My brother was going to come down to visit for a weekend. He had done some diagnostic work and had me order a timing kit and a camshaft position sensor from ECS.
So, with my assembled parts, I brought the car in to a reputable shop. Anyway, the guy does the work and now the car is ready and saying that the CPS took nearly 4 hours more of work.
Civic - Honda :: Engine Swap / Camshaft Position Sensor Replacement?
I had an engine swap recently done on a 2005 Honda Civic, and within a couple days, Check Engine light came on. Mechanic ran the error code and I have to apparently replace the camshaft position sensor. They are claiming that the sensor was not replaced in the engine swap, and so not covered by any warranty.
View 10 RepliesLexus ES 2007-12 :: Code P0368 - Camshaft Position Sensor Error
2007 Lexus ES350 with 177k miles. Getting a P0368 (Camshaft Position Sensor B Circuit High Bank 1) Error. I can't seem to find online where this sensor is located at.
View 2 Replies