Sonata NF (2006-10) :: Camshaft Position Sensor Error - Check Engine Light On
06 sonata 3.3 L V6. Light has been on for a month or two...took it in to mechanic yesterday and it's a camshaft position sensor error...it makes total sense to me now because my cars been starting hard, seems like it gets hotter then usual...and had a "clicking" noise for about 10 mins, then gradually goes away. it takes a few extra cranks now to start the engine unless it was already fired up.
Also does a jerk once and a while around 40 km/h. I looked online and those seem to all be symptoms of a failed camshaft position sensor (CMP). Would those symptoms seem about right? Am I okay to drive slowly for the weekend before I get the new sensor installed? The mechanic didn't seem to worries about me driving for just the weekend...but it's worrying me a bit...
Sonata NF (2006-10) :: GLS Error Code P0011 - Camshaft Position Sensor Was Detecting A Fault
My check engine light came on the other day, and I went to Autozone to have the code read. Of course, that indicated the camshaft position sensor was detecting a fault. I read through all the posts relating to the fault, headed up to my local Hyundai dealer, and picked up the oil flow control valve for about $50 plus tax. While I was there, I figured I might as well have them do an oil change, since it was way past due. No point in putting in a new part with dirty oil..right? They did the oil change, washed the car and I was ready to roll. My plan was to replace the part myself, but magically, the check engine light has not come back on since.
View 8 RepliesMazda - Protege :: 2003 - Camshaft Position Sensor Location?
Where the camshaft position sensor is on a Mazda Protege5 2003. I can't seem to find any information about this particular car.
View 2 RepliesFord - Explorer :: 2002 - Chirping Noise When Starting From Cold / Camshaft Position Sensor Location
Have a 2002 Ford Explorer 4.0 6cyl. w/ around 150K
I recently started hearing a little chirping noise when starting from cold. The rate of the chirping increases with the rpms (reving in neutral or when speeding up while driving). The sound usually goes away after things warm up.
Doing some research, the most suggested cause for such chirping is something called a Camshaft Position Sensor. Information mentions that this item can either need lubrication or to be replaced.
I was going to try lubrication first....then if the problem persists...replace.
My biggest issue is locating it on a 2002 4.0 Explorer (4 door, 4wd). I've read different reports for different Year models (mostly 97-2001)...which often include pictures. But I can't find ANY pictures for the 2002 4.0
QUESTION: Where it is located on my 2002 6cyl model? I read one account of it being on top of the driver's side valve cover....and I DO see an item in that location secured by one bolt..and it does have an electrical wiring harness attached....but I'm not sure...and have not seen any photos that look like my engine.
I've attempted to upload a picture of what I think maybe be the sensor (circled on red).
I've also come across an item called a "CRANKshaft position sensor".....are these different items, and, if so, does the crankshaft p.s. also "chirp" when needing lubrication or replacing ?
Lexus ES 2007-12 :: Code P0368 - Camshaft Position Sensor Error
2007 Lexus ES350 with 177k miles. Getting a P0368 (Camshaft Position Sensor B Circuit High Bank 1) Error. I can't seem to find online where this sensor is located at.
View 2 RepliesLexus ES 2007-12 :: Code P0365 - Camshaft Position Sensor Circuit Malfunction On ES350
I have a 2007 ES350 with 90k miles. Purchased in August. I had ignition coil go out and decided to change them all and the spark plugs. When changing cylinder 5's coil and plug, I tried to push the wiring harness out of the way to remove the coil. Result, I moved the wiring harness too far and disconnected the 3 wires (black, yellow and red) that were connected to the cam position sensor connector. (I should've just removed the sensor SMH) I disassembled the connector, got it down the internal pins, soldered the pins to the wires, placed the pins back in the connector and reassembled it with the wires in the order that they appeared to originally be.
Plugged it back in and put everything back in place. Started the car and code P0352 was cleared but replaced with code P0365 Camshaft Position Sensor B - Bank 1 Circuit Malfunction. I'm thinking, either I put that pins back in the wrong order or one of the wires isn't properly soldered in. Either way, I ordered another connector and it should be here tomorrow. I need Either a wiring diagram or a picture of the camshaft position sensor closest to cylinder 5 connected with the wires in the proper order .
Sonata I45 (YF - 2011+) :: Crankshaft Position Sensor Location?
Looking for a picture or description where this sensor is located? I assume very close to the crank pulley, but I'm hoping I will not need to remove the crank pulley to gain access to this sensor. I have a 2011 Sonata, 2.4L engine.
View 3 RepliesJeep - Compass :: 2007 - Crankshaft Position Sensor Location
My son has a 2007 jeep compass 2.4l engine. He needs to change the crankshaft position sensor. Where to find it? He got a pic from autozone but you can't tell where it is on the engine.
View 7 RepliesGolf/GTI VI :: Camshaft Position Sensor Oil Leak
Wasn't there a TSB for this? I've searched Google and Vortex with nothing for the MKVI but I could swear I read something on this.
I am accumulating oil/grim right around the sensor and it's beginning to irritate me. I want to take her to the dealer but would rather know for sure of any possible TSB out there so I have something to reference.
Elantra XD (2001-06) :: Camshaft Sensor Location And Timing
I have a 01 Elantra and my daughter has a 02. Both cars have the camshaft sensor at the front (timing belt) end of the engine. My daughters car is a early model with a 01 engine in it. My understanding is that later 02 engines moved the camshaft sensor to the ignition coil end of the cylinder head. My question is did the timing remain the same so that if I put a 01 engine in a late 02 body and spliced the sensor in would it work correctly?
View 8 RepliesFord - Explorer :: 1993 V6 - Location Of Camshaft Sensor?
Does my 1993 ford explorer sport 4.0 L V6 engine have a camshaft sensor and if so where is it located?
View 2 RepliesGTI 337/20th Anniversary :: Where Camshaft Position Sensor Located Under The Hood
The CEL just came on in my 20th AE Gti. The code indicates a Camshaft Position Sensor issue. Don't know where this sensor lives under the hood of the GTI? Is an easy enough fix for a beginner to attempt? (have hand tools, former bike mechanic, but no shop just a parking lot in the Texas sun!)
View 6 RepliesAccent LC (2000-05) :: Camshaft Position Sensor Code P0342
So my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 RepliesAccent LC (2000-05) :: Camshaft Position Sensor - Circuit Low Input
My 1.5L 2000 Hyundai accent is reading p0342 code.(cmp sensor circuit low Input). I have changed out the sensor from a parts car and it's still reading this code. I've read it could be timing or an issue with the starter wiring.
View 3 RepliesElantra XD (2001-06) :: 2003 - CEL Code / Bad Camshaft Position Sensor
I am new to Hyundai. I just picked up a 2003 Elantra and I'm doing a couple fixes to it. When I got it, the engine light was on and the code displayed said it had a bad camshaft position sensor. Is this a common issue with the car and is it an easy fix?
Also, I just installed new brake pads and a new battery. Now the battery and brake lights are on, although I know I didn't break anything. Could installing a new battery cause the two lights to come on?
Accent LC (2000-05) :: Code P0342 - Camshaft Position Sensor
My daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 RepliesFord Ranger / B-Series :: Camshaft Position Sensor On 1996 2.3L
My check engine light came on about a week ago and was unsure what the problem was. So I tested the codes and it said that the camshaft position sensor was bad. So I have tried finding this sensor but little to no luck. I was unsure if it was the 2 or 3 pin, but after looking at some pictures of the engine I'm thinking it is a 2 pin. I attached two pictures of what I think might be the sensor? But I am unsure. This was right next to the timing belt cover, which is where it said it was located. I have a 1996 Ford Ranger, 2.3L.
View 6 RepliesCelica :: 1997 7afe 1.8 ST - P0340 Code For Camshaft Position Sensor
I am getting the code for the camshaft position sensor. Erase code, comes back immediately. I don't even think this car has a camshaft position sensor.. I guess the first step would be locating the little bugger. Crankshaft position sensor is new and seems to work fine. Car is running btw.
View 5 RepliesJimmy :: 95 Running Rough / Stuttering - Camshaft Position Sensor Code
I have replaced the camshaft pos sensor multiple times from Autozone (warranty ) and replaced with one from Advance Auto still get cam sensor code changed crankshaft sensor today still running like crap, stuttering. I have also done a complete tune up and the Distributor has not been pulled.
View 1 Replies