Ford F-150 - 1997-2003 :: 1999 - Squeaking Badly - Replace Chassis Bushings?
I am buying my Dad's '99 F-150 4x4 Lariat from him and this truck squeaks something terrible. I am assuming that the chassis bushings need to be replaced. I have 2 questions.
1. Am I on the right track to solve the problem?
2. How hard is the job?
Prius (Gen 2) :: Replace The Bushings In The Trailing Arm?
She's 10 years old with most of her life spent in AZ. This means that a lot of the rubber she has is dead or dying.
Is it possible to replace the bushings in the trailing arm or is it true that you have to replace the entire trailing arm?
Yukon :: 99 Replace Hinge Pin And Bushings On Barn Door Hinges?
Replacing the hinge pin and bushings on the barn door hinges? My drivers side upper hinge pin has completely sheared in two. I took it to the body shop today for replacement and they could not fix it. I think it was more labor intensive than they had imagined.
Anyway, they say I have to replace both the door side and the truck side hinge which are both welded on despite the bolts on the truck side. I found a site that retrofits the front door hinges and they have a special tool to press the old hinge pin out. Is this possible to press out the hinge, or should I try to drill them out?
Ford Super Duty (1999-2016) :: 2006 F350 - Clunk In Left Front End - Radius Arm Bushings Bad?
I drive a 2006 Ford F350 4x4 Crew Cab. I think the radius arm bushings on my truck are bad. I get a clunk going over bumps on the left side in the front end.
I'm assuming it is the bushing in the rear of the radius arm, but I haven't taken it apart yet because I want to have the parts in hand. I ordered a bushing, part number 5C3Z3B203AA. But it looks too small when I hold it up to it. What is the part numbers for the radius arm bushings?
Or am I looking at the wrong thing for the clunking in the front end? I just did the ball joints with Moog both sides top and bottom. The shock bushings look alright. I have replaced the front sway bar bushings thinking that was it. What else could it be?
Golf/GTI VI :: Bushings On The Front End Links Are Worn
I'm scheduled for my first HPDE next week and I just discovered that the bushings on the front end links are worn. I don't notice any issue when taking curves and I'm asking due to the timeline of when the dealer will get the parts...it'll be cutting it close before the event.
View 3 RepliesTiguan :: Front End Clunk - Sway Bar Bushings?
My Tig has been doing a sharp clunk (single) for awhile when going a bit too fast over speed bumps. I just ignored it, as I'm not flying over bumps regularly and I had just replaced the OEM struts all around. Now when accelerating over 60 kph the car has a side to side shimmy. Also when compressing or unloading the front end suddenly, like with dips on the road, makes it clunk. Checking the various suspension components?
View 6 RepliesFord Excursion :: Front End Clunking / Track Bar Bushings
So I can clearly see the track bar clunk in and out about 1/4 inch when the wheel is turned in either direction...guessing its time for new bushings.
What's the latest and greatest on these? or is "whatever they have on sale at summet from moog" is fine?
OEM only? Truck has a 4" lift, stock bar attached to the drop bracket.
Pontiac - 6000 :: 1988 - How To Replace The Battery
I tried to put in a new battery for my mom's 1988 Pontiac 6000, but could not get the battery out with having to disassemble other parts of the engine. What is the easiest way to do this?
View 8 RepliesDodge - Caravan :: Clunking And Some Wobble In Front End / Squeaky New Bushings
So I replaced the stabilizer bushing on my 2005 Dodge Caravan, as there was a bit of clunking and some wobble in the front end. I'm sure there's more to do (other suspension parts to replace), but the bushings were obviously worn when I looked at them. The clunking is gone, and the suspension feels better, but now the bushings make a scrunching rubber sound when I drive over uneven pavement and also when I first accelerate. I assume its the stabilizer bar flexing, but also assume I shouldn't be hearing it. After all, who would want new noisy bushings? Nothing else is new on the front end (except rotors and pads).
View 19 RepliesGolf IV R32 :: Front Lower Control Arm Bushings Completely Separated
Front lower control arm bushings are completely separated. Looking to upgrade in some way to poly bushings or some other sort of performance setup.
View 4 RepliesFirebird - Pontiac - Noises :: Ringing Appear From Front Of 1996 V6 Engine
My 1996 Firebird with 3800 series II V6 engine makes a ringing noise. The noise appears to come from the front of the engine (pulley area) and sounds like an old fashioned fire alarm. It usually occurs after the engine has warmed up and cannot be heard from inside while cruising.
View 4 RepliesPontiac - G6 :: 2008 - Vibration In Steering Column / Noise In Front Of Engine
I have a 2008 Pontiac G6 GT. I loved my card until I had to replace the rotors and changed to an all-weather tire. Now, I can feel a vibration in the steering column; a vibration in the seat and floor; there is a noise in the front of the engine when I am going over bumpy or icy roads; and the car pulls to the left when I have been stopped at a light or an intersection. Oh - When re-starting on a slightly icy or gravel-y road, I also get a sound that sounds like gears grinding -- not like the traction control is kicking in.Frustratingly enough -- the car can go from feeling like it is driving "tight" -- like the power steering is out -- to driving "loose" like the steering wheel is ready to fall off the car and vibrates like it never has before. No one notices the vibration but me (which is frustrating because I have driven my car over 30,000 miles, and what seems "normal" to others, is not "normal" to me).
View 13 RepliesPontiac - Grandprix :: Rear Brakes Noisy - Pad Down To Metal - Replace Both Rotors?
i wrench on kids car. have done all 4 brakes in last 5 yrs. kid said front brakes were noisy. 06/01. 1 pad was worn thru to backing plate. messed up rotor. i decided to replace both rotors since cost was minimal. piston in caliper was stiff. decided to change caliper 1 week later. yesterday kid said rear brakes were noisy. rear discs. 1 pad was down to metal. replaced pads. rotor looks rough. other rotor is ok. need to get 1 new rotor. should i change both? pistons in calipers pushed in easy. feel smooth. caliper pins look fine.
View 11 RepliesGolf IV R32 :: 2003 - Fitting Supercharged Boost Gauge
I live in Scotland so have a right hand drive 2003 MKIV R32. I got a VF stage 1 kit fitted last year and now I want to fit a boost gauge. I've bought a NewSouth indigo 0-30 psi gauge and a column pod.
What I need to know is where to take the feed from, where is the best place to fit the vacuum tube to get the best readings? any photos would be good.
I plan on fitting it this weekend along with my oil pressure gauge.
Ford Super Duty (1999-2016) :: 2006 - Front End Clicking And Grinding While Making Turns - Replace?
I recently noticed my truck (2006 f250 v8) making some clicking noises on really sharp turns and also horrible grinding when stopping (like the brake pads were shot).
I replaced the pads a couple years ago, so I didn't then they were bad, but I took a look tonight. What I found was a couple of seals blown on both sides!
What these are and how this might have happened? They look the same on both sides. How do I replace them?
Ford Super Duty (1999-2016) :: 2003 - Replaced Front Hub Now Driver Side Leak - Replace All?
I replaced my my front hub assemblies on my 2003 F250, 4x4, about two years ago and my driver side hub is leaking. I first noticed it the other day when I tried to shift into 4 wheel drive and my hubs would not lock in the ESOF system.
I used a vacuum pump and it leaked down pretty fast so I assume the knuckle/axle seal is the culprit.
I plan on ordering these three seals:
Amazon.com: f81z-1s175-hca
I am also noticing another # for the axle seal. It is 3C3Z-3254-CA. Which is correct for my 2003?
Are my questions would I actually need to replace all three? The dust seal is not leaking at the moment. Should I go ahead and replace it anyway?
What type of grease do I need to use the seals? I have some disc brake bearing lithium grease in the cabinet. Will this work or do I need to get a specific type
Lastly, I've seen a post where members have made their seal seating tool out of the galvanized pipe, cap, and a flange. The flange is said to be too large and it would have to be ground down for the right diameter.
Ford Super Duty (1999-2016) :: 2003 F250 - Replace The Front Hub Wheel Bearing Assemblies?
I am needing to replace the front hub wheel bearing assemblies on my 03 F250 4x4. I know Ford changed the studs from coarse thread to fine thread in between the 02 and 03 model years. Mine has a build date of 08/02 and I haven't been able to find the exact date they switched over. I'm ordering the parts online and want to get it right the first time.
View 3 RepliesGrand Prix :: 2000 GTP - How To Pull A Supercharged 3800 Motor
I have a 2000 grand prix gtp, I am trying to pull the motor so i can change some things up so i can race it. But how to pull the motor or transmission with it.
View 7 RepliesFord Super Duty (1999-2016) :: 2000 - E-Brake Won't Working - Replace Front / Intermediate / Rear Cables?
2000 F 350 super cab 4wd 7,3 auto srw long bed. Problems with emergency/parking. My cable probably needs replacing. My pedal will go to floor when setting the e brake. I use very infrequently, but when loading hay on the big bale trailer. I could ignore it but when hit the slightest bump the brake pedal goes down just enough to activate the brake light on the dash and activates the bell/chime until I raise the brake pedal up.
When searching this site one post stated that should not happen. I am trying to figure out if I need to replace the front cable, intermediate cable, and rear cables. And do I need to replace the foot pedal assembly as well. What are the part numbers for these. I generally order from who ever took over Edpartguys for original ford parts. I have new cryo rotors and Hawke brake pads.