Mazda - Protege :: 1998 - Won't Start At Cold?
I have a 1998 Mazda Protege LX 1.5 L 4 Cylinder and i have been having some starting issues, and stalling at stop lights.
To be clear i have replaced/cleaned, Injectors, Spark Plugs, Spark Plug Wires, Distributor Cap, Distributor Coil, Air Filter, Cleaned MAF, Cleaned the EGR Valve,
My car won't start in the morning, just gives cranks but if I press gas pedal it starts and have to keep it until engine gets hot enough. then it works till the car cools down again, and repeat the problem in the morning when I have to go to work. When the car is warm it starts fine but has idle issues regardless of temperature. As usual when the engine is cold or cool, it won't start.
Visited 2 different mechanic shops and the problem still exist, I don't know how and what they did it, it only worked for couple of months and the engine noise was bit high, I believe he just increased the idle, When i am at stop lights it has a rough idle and tries to die, When it idles it idles rough, Every once in a while I get a CEL Cylinder Misfire on cylinder 4. I'm confused on want to do , Don't know what else to do and its getting tiring, The car also feels like a lack of power.
Mazda - Protege :: 2003 - Stalls At Start Up When Warm Up?
I have a 2003 Mazdaspeed Protege that is having a stalling problem. The motor has about 30k miles on the block with around 3k miles on the internal components (rods, pistons, cams, etc.). Cylinders were bored 20 over and head was machined.
This stalling, or almost stalling, problem occurs when I start the car after it's been warm for awhile. For example, if I were to drive for an hour, park it for 45 minutes, and then come back out to start it up. It'll fire up, drop to idle, and then the idle will dip, stalling 50% of the time. The rough idle lasts anywhere from 5 to 20 seconds, and then usually fixes itself.
Giving it some gas does nothing to alleviate the problem; sometimes making it worse. Cleaning the idle air control valve solved this for a few days, and then it was back to its old ways. These symptoms do not occur on cold starts or if I restart the car after 5 or 10 minutes of it sitting. We couldn't find any vacuum leaks and there are no codes being displayed.
Mazda - Protege :: 2000 Won't Start / Burned Rubber Smell
I think I broke my car. I just bought this car a few months ago and all seemed well. I bought new tires, changed the oil, had the brakes inspected, you know the things daddy's tell their daughters to always be sure of. I have had no problems with the car till last weekend. My boyfriend and I got into an argument, long story short I sped off, using his words "hot rod style".
I smelt burned rubber (not so new tires anymore) but I figured it was just that. When I got back home my boyfriend said that he smelt something burning under the hood. No smoke or fire just a burning odor. The next morning my car wouldn't start. We jumped it and it ran just fine. Did the errands for the day no problem.The next morning it wouldn't turn on again, this time when we jumped it, it just wouldn't start. I have checked the battery at AutoZone and they said it was fine. the fuses are all good as well.
Mazda - Protege :: Shutting Off Intermittently / Won't Start / No Click Or Turning Over
It's a 2002 Mazda Protege... The car shut off once while running in the driveway. Completely: engine, radio, everything. I took the key out and put it back in a couple of times and got nothing, no click, no turning over. Did it one more time, and it started up as if nothing was wrong.
Then again the next morning. Car won't start. I notice all the electronics are working while the key is in the accessories position. They shut off as soon as the key is in On, and nothing when turning to start. Took the key out, waited a minute or so, then tried again and everything worked as if nothing was wrong. I'm guessing this might be the ignition switch?
Mazda - Sparkplugs :: 2000 Protege Won't Start After Timing Belt Change
2000 Mazda Protege 1.6l Just replaced timing belt, tensioner, idler, water pump, plugs and coil packs
I have checked the timing about 10 times before puting everything back together by rotating the engin clockwise. No stiff point and marks lining up perfectly every time.
Though when I turn the key in the ignition, the engine cranks but doesn't start.
Can't really check the sparks cause I am on my own, but seems like the spark plugs in 1 and 3 are wet with fuel and 2 and 4 are dry.
Mazda - Protege :: 2000 - Won't Start / Sometimes Sputters And Lopes Before Just Stops Firing
I have a 2000 Mazda Protege LX with 38k miles on it and a 1.6L engine and it starts fine in the morning to go to work and starts fine in the afternoon to go home from work. If I get home and change clothes, hop in the car to go somewhere, it won't start, turns over like it's out of gas, sometimes sputters and lopes before it just stops firing. It seems to only do this in the afternoon, specifically between 3pm and 5pm, never after dark or in the morning. I can drive all day long as long as I don't cut off the engine.
After sitting for about fifteen to thirty minutes, it will start like nothing ever happened. So far, it only does it once per day. After I get it started in the afternoon, I can seem to go anywhere, stop as many times as needed, and it keeps starting every time. It seems to be getting more frequent as the weather warms, never did it in January or February, but so far has done it every time I try to start it when the temp is around 80 or higher. I get no engine light, temp gauge is normal.
Mazda - Protege :: 1999 - Transmission Fluid Leak
I have 1999 Mazda Protege that has a transmission fluid leak. I took it to a transmission shop close by, and they said it is either the torque converter or the front pump. I also have oil in the coolant reservoir, which I was told they wouldn't be able to tell where the oil is coming from until the leak is fixed.
My question, is what could have caused either the torque converter or the front pump to leak? Wear and tear and old age? Or could it have been caused by something else?
I realize at some point I will just have to decide, but any input on whether it's a worthwhile fix? The shop quoted me $787 for the front pump, and said the torque converter would be a few hundred more. That's not taking into account the possible issue with the radiator from the oil in the coolant reservoir.
The car has approximately 160,000 miles on it. The catalytic converter will need to be fixed at some point in the future, the O/D light is flashing (though I'm not sure if it's related to my transmission problems at all), cruise control doesn't work, and the drivers side mirror is broken...
Mazda - Protege :: 1999 - Loses Power Intermittently?
My 1999 Mazda Protegé has the hiccups ...every now and then it loses power for a fraction of a second. It lasts just long enough to feel it clearly, but it's gone before I can think about it. Very distinct sensation, but it certainly doesn't push me against the seat belt. It's been doing this for over a year (about 5-7,000 miles). No Check Engine Light has appeared at any time. The timing belt was replaced a few thousand miles back.
Yes, I've had it to a mechanic, a trusted local one. I even left it with him for several days. The car won't hiccup for him. I sometimes notice it around town, but I notice it more when driving on the highway (which has probably been over half my mileage in the past year), but I'm still disappointed that it won't do it for him. He suspects a spark plug wire -- he says it's probably only one cylinder based on my description -- but doesn't want to start replacing the wires if he can't diagnose it.
Recommendations? Should I just replace the wires and figure if that doesn't do it, it's part of the cost of diagnosis? (This much I should be able to do myself.) Should I try something else? Actually, as I think about it, he could have been encouraging me to replace the wires myself.
Mazda - Protege :: Very Rough Start / Idles Fine And Stalls As Soon As Touch The Pedal
1995 Mazda Protege1.5 LAuto153K miles.
My car was running fine, then one day it started sputtering while driving, mostly when I accelerated. It stalled and I could not get it started. This happened on a day when it was raining hard, but not sure that had anything to do with it. A few days later when I went to pick the car up it started right up, it had stopped raining and been dry for 2 days prior. But about a mile into the drive back home it stalled and I could not get it started.
Here is what I have tested so far.
- Put in new fuel filter.
- Tested the fuel pressure and pressure regulator
- Tested the injectors with a noid light.
- Tested that the spark plugs were producing a spark.
After I pulled the plugs and cleaned and dried them (they were wet with gas) the car started, but I think not because of anything really related to the plugs. What I've noticed is that when cranking the engine if I give it gas it will not start but if I keep off the throttle it will reluctantly start. But once it starts the idle is smooth and as it should be. Then if I give it any gas it immediately stalls. It seems to me given these symptoms that it is getting enough air to idle but not enough air to match the increased gas.
The only CEL code that I'm getting (which I had before this issue occurred) is the "closed throttle position switch" (I forget the number). If it was an MAF, or IAC, or EGR issue would I not get a code? What this could be and how to test it. Again my guess is its an air intake issue but not sure where.
Mazda - Protege :: 1999 Revs In Park - Won't Go Forward In The Morning
I have a 1999 Mazda Protege. In the mornings when I start my car, it revs in park, but the rpms go down when I put it into reverse and back out of my spot. When I put the car in drive, however, it will not go forward for at least 5 seconds (time has been increasing). I can press the gas and the engine will rev, but it takes a long time to actually get my little car moving forward. Is this a new transmission problem? I love this car and live in fear of having to replace it.
View 4 RepliesMazda - Protege :: 1999 - Idle Speed Is Higher Than Normal
The idle speed is higher than normal, about 800-900 RPM. Whenever I stop for the traffic light, the engine will behave as if someone is pressing the gas pedal intermittently. It has new spark plug wires and coil.
View 8 RepliesMazda - Protege - Tires :: 1999 - Rear Passenger Tire Seemed Very Low
I bought a 99 Mazda Protege ES two years ago. About eight months ago, i noticed that my rear passenger tire seemed very low. Not flat, but very very low. I filled it back up to 32psi, as recommended in the owner's manual. Then in June, it seemed low again. I bought a pressure gauge, checked all my tires and filled up the one that was low (14psi). Throughout the summer and early fall, I would check my tires once a month and the rear passenger tire would always need air. Now it is the end of October and I've had to fill the tire up three times in the past month.
Obviously, I need a new tire. My question is: is there a viable way to fix a slow-leaking tire? Or do a need to buy a new one? Also, can I just buy one tire?
Mazda - Protege :: 1999 - Disappearing Coolant And Faint White Smoke
I've owned this car for a year and a half. A few weeks ago, my car stopped running while i was idling. It started back up without a problem. When I got home, I saw that the coolant reservoir was empty and i topped it off. last week, a faint white smoke came from the hood while i was driving. When I got home, I saw that the coolant reservoir was empty again, so i topped it off again. This morning, the faint white smoke appeared from under the hood again. The coolant reservoir was full and there were no visible signs of leaking anywhere.
View 2 RepliesMazda - Protege :: 1999 Air Bag Light Blinking / Cruise Control And Horn Deactivated After Clutch Replacement
I took our '99 Mazda Protege in for a clutch replacement. The mileage is over 150k. The car was returned with the air bag light blinking and the cruise control and horn deactivated. All were fine beforehand. The shop eventually admitted that they could have broken the clockspring during the repair. They are going to get back to me tomorrow with a quote for the repair and they told me they are going to "work with me" on the cost. I don't understand why I should pay for anything associated with the clock spring repair. Another mechanic told me they had to secure the steering during the clutch replacement and probably forgot to do it, furthermore they should cover 100% of the repair.
View 19 RepliesMazda :: 2002 Protege 5 - Hesitation At 3k Rpm
Have 2002 mazda protege 5 . During acceleration at 3000 rpm the engine hesitates. Computer said o2 sensor, replaced it but that wasn't it. Drilled out both catalytic, that wasn't it. Found hole in mass air flow tube, figured that is it. I haven't replaced that yet, however I used gorilla tape thinking it would be a temporary fix but that didn't work. I know I need to replace that tube, but think that it may now be a fuel pump issue??
View 5 RepliesMazda :: Protege ES 1.8L - Rattling And Knocking Front End
2000 Mazda Protege ES 1.8L
What's a good way to find whats the cause of all the rattling and knocking in the front end of my car when going over uneven terrain? It seems that noise appears only if one of the wheels is lifted up a little bit. I am attaching a picture describing the "motion" here:
Steering wheel doesn't shake when driving at high speeds and is fairly stiff, but it does pull to the right a bit, maybe because I didn't perform a front end alignment (I know this is not good) after I had most of the stuff in the suspension of the replaced; all 4 struts + boots + mounting blocks, ball joints, control arms...
Now the only part, I didn't replace was the sway bar link on the passenger side and it's being knocking for 3 years. The one on the driver side was replaced at the time the struts were replaced but I didn't have enough money to pay for the other one.
Another mechanic told me when I was quoting that sway bar links aren't really necessary as a safety feature, and a google search showed me that there are people that just take the sway bar off the car, so I left it there and just tried to live with the noise. now I am noticing the driver side is knocking as well, and I am wondering if it has to do with because I didn't replace the one in the passenger side?
I just want to rule out the possibility of another component being the cause of the noise because I am prioritizing safety over ride comfort in my attempts to save some money.
Mazda - Protege :: 1996 - A/C Isn't Blowing Cold Air
it was over 100 degrees today in Lawrence, Kansas and on the way home from work, the air conditioner stopped making cool air. Hot air now comes out. This is a different problem that the poster before me seems to have. Mazda Protégé, 1996, 128,000 plus miles on it.
A reconditioned one was installed in 2006, compressor replaced in July, 2012.
Mazda - Protege :: Loud Tire Noise Between 20 And 40 Mph
I read here that some tire noise can be caused by bad belts. How do you know if the tire belt is bad? My tires get loud between 20 and 40 mph. Mechanic says the tires are OK but to replace them to get rid of the noise.
View 7 RepliesMazda - Protege :: Brakes Stuck And Burning Up
Basically, my car (2002 Mazda Protege) has been acting like my brakes are engaged. Not all the time, though - The first time I get out and drive it, it drives smooth as silk like always. But then after I put it in park and then get back in and head out (I'm a delivery driver, so this is constant), sometimes it feels like the brakes are constantly being pressed. No, the emergency brake is not on. Most of the time it's almost not even noticeable so, like an idiot, I put it off for the past week. But today, it was very, very, very bad. I was having to press the gas to the floor to get up to speed, and then it was constantly trying to slow down. My brakes were definitely getting burned up while it was doing this, but luckily it stopped.
It may be unrelated - I know I have an oil leak, but today I saw a very unusual spot where something leaked out in my driveway. I checked my oil, and it was where I expected it to be, but this was a relatively large stain which would be very unlike my current leak.