Mazda - Protege :: 2002 Engine Overheating / Rattling Noise Behind The Dash
I drive a 2002 Mazda Protege and it's been great to me until this past weekend. I had a 4.5-5 hour trip ahead of me and Google Maps told me a more direct route (i.e. not using the interstates) would save time. It must have erroneously assumed that the highway comprising basically the entire trip would be speed limit 55-65 the entire way. Instead, I found myself slowing down to stoplights and stop signs in small villages between 15-minute sprints. At some point, the interior heat stops - the air being pulled in from outside is not being warmed at all, no matter what settings I fiddle with. Not long thereafter I notice a rattling noise behind the dash. From inside the car it sounds almost like an animal skittering around in the chassis - irregular, short and clipped. With the hood up and an ear to the engine, it sounds like a piece of plastic fluttering in the wind, but with a faint electric "crackling" quality. Soon thereafter the check-engine light illuminates.
Before long the engine overheats and I pull over to the side of the road. Nothing appears to be leaking, and the crackling sound is the only thing noticable. Being in the middle of nowhere, I jumped back in and proceeded to drive at about 35-40, which was warm on the engine but enough to get me to a small town. At this point I checked the coolant reservoir and it was empty. Bought some from Wal-mart, poured it in, and headed out. Things looked fine at first since the engine had sat cold while I was running errands, but pretty soon it was overheating again at speeds as low as 30mph. After getting it towed to my destination, I took it to a garage the next morning. They couldn't find anything wrong with it, and indeed when I drove it back to the hotel that morning the engine behaved normally, the check-engine light was off, and the interior heating was functioning properly.
The next morning, when it was time to depart (but again after an entire night of sitting in the cold), a 20 minute drive to breakfast was smooth as before. Thinking that the mechanic had either waved a magic wand or I'd gotten extremely lucky, I hit the highway and did 65 for a good 20 minutes until the engine began to overheat again. Slowing down to 45 bought a few more minutes to find an exit, but eventually I had to pull over. Popping the hood, I notice the coolant in the reservoir is bubbling to the top! Thinking the mechanic might have added more and overfilled it, I cursed him in absentia. After a good fifteen minutes of cooling off, the coolant settled and in fact drained the reservoir entirely; I refilled it to the line and, again being in rural snowtopia with few options, decided to hit the road again. Not wanting to tempt fate, I stuck to 55mph and the car ran fine for an hour and a half (with the interior heat blasting, per a friend's advice). I stopped once to check the coolant and all was as it should have been - just below the line I'd filled it to earlier. Closer to a city, I decided to experiment again and took the speed up to 60mph.
This was great for 20-30 minutes but eventually the engine began overheating ever-so-slowly and I had to pull over, let it cool off, and replace another full reservoir's worth of coolant that had disappeared before I kept going. I drove the rest of the way home going no faster than 55mph and stopping on occasion to check the coolant. It overheated once even while doing 55mph, but a 15 minute break + coolant refill bought it the rest of the trip. In summary: Although not 100% correlated, going faster than 55mph seems to trigger the engine overheating, at which point the rattling noise appears and the coolant begins to bubble its way back up the reservoir (like it's boiling?!). I'm not sure how the coolant is disappearing because I'm unable to find any leak, nor is there any extra exhaust that would suggest it's burning.
Mazda - Protege :: 2002 - Mystery Noise Sounds Like A Creaking Or Bumping In Front End
I drive a 2002 Protege5 with about 125K miles. The suspension (struts and mounts) and brakes have been recently replaced and, with the arising of the Mystery Noise, checked by a mechanic as of last week. The noise sounds like a creaking or bumping in the front end of the vehicle, and comes primarily when slowing to a stop, when the brakes are applied or not. The pace slows as you stop. And it is not always predictable: the mechanic could not recreate the noise, but my wife and I hear it all the time.
I'm just speculating, but should we be looking at the bearings, axles, CV joints... or is this going to get even more expensive? What should I ask the mechanic to look at on this thing?
Mazda - Protege :: 1996 - Front Turn Signals Malfunctioning / Wires Cannot Be Reconnected
1996 Mazda Protégé, 128,821 miles, in town driving 5000 miles per year in recent years.
I hit the frame of my garage door about 6 months or more ago which partially pulled off the front bumper area and knocked the right turn signal lens and headlight out of whack. My handyman fixed it up, by using good quality baling wire so the turn signal and headlight etc worked.
Then, I did the same thing a couple of weeks ago. (I was trying to avoid hitting my bicycle which I had just had reconditioned for an ungodly amount of money) My handyman is unavailable to fix it again. I have gotten stopped once by the police for the malfunctioning turn signal so it was time to get it fixed.
Mechanic (same one as previous posts) said it will cost 1500 to replace the bumper area etc so the front turn signals will work. He absolutely insisted that the turn signal wires cannot be reconnected. He reattached the bumper area "temporarily". I am willing to pay to get the turn signals functioning but do I need to replace the whole bumper assembly unit?
Does this seem plausible?? I just want the turn signals to work. I do not care about how it looks. (I drove the car in the interim with a bright yellow bungie cord holding the unit together)
Mazda :: 2002 Protege 5 - Hesitation At 3k Rpm
Have 2002 mazda protege 5 . During acceleration at 3000 rpm the engine hesitates. Computer said o2 sensor, replaced it but that wasn't it. Drilled out both catalytic, that wasn't it. Found hole in mass air flow tube, figured that is it. I haven't replaced that yet, however I used gorilla tape thinking it would be a temporary fix but that didn't work. I know I need to replace that tube, but think that it may now be a fuel pump issue??
View 5 RepliesMazda - Protege :: 1999 - Won't Start When Hot
I have a 1999 Mazda Protege. As of last summer it started giving me problems with not wanting to start after I had driven it around town for a little while. (IE: to the grocery store, to the bank and then to my sister's house. It wouldn't give me the same problem if I just went to the grocery store and back home. It would start up fine and I'd be on my way. Only when I went somewhere and shut it off then repeated that a couple more times.) I took it to a mechanic who wholeheartedly believed it was the coil packs not allowing my car to function properly.
So we replaced those and everything seemed on the up and up. (Keep in mind that this was towards the end of summer and the temperature was dropping.) The car was perfect all throughout the fall and winter, but now that the temperature outside is starting to rise again it's beginning to do the same thing it did last summer. I don't want to take it to another mechanic that's going to have me dish out an extravagant amount of money again only for the problem to persist.
Mazda - Protege :: 1996 - A/C Isn't Blowing Cold Air
it was over 100 degrees today in Lawrence, Kansas and on the way home from work, the air conditioner stopped making cool air. Hot air now comes out. This is a different problem that the poster before me seems to have. Mazda Protégé, 1996, 128,000 plus miles on it.
A reconditioned one was installed in 2006, compressor replaced in July, 2012.
Mazda - Protege :: Loud Tire Noise Between 20 And 40 Mph
I read here that some tire noise can be caused by bad belts. How do you know if the tire belt is bad? My tires get loud between 20 and 40 mph. Mechanic says the tires are OK but to replace them to get rid of the noise.
View 7 RepliesMazda - Protege :: Brakes Stuck And Burning Up
Basically, my car (2002 Mazda Protege) has been acting like my brakes are engaged. Not all the time, though - The first time I get out and drive it, it drives smooth as silk like always. But then after I put it in park and then get back in and head out (I'm a delivery driver, so this is constant), sometimes it feels like the brakes are constantly being pressed. No, the emergency brake is not on. Most of the time it's almost not even noticeable so, like an idiot, I put it off for the past week. But today, it was very, very, very bad. I was having to press the gas to the floor to get up to speed, and then it was constantly trying to slow down. My brakes were definitely getting burned up while it was doing this, but luckily it stopped.
It may be unrelated - I know I have an oil leak, but today I saw a very unusual spot where something leaked out in my driveway. I checked my oil, and it was where I expected it to be, but this was a relatively large stain which would be very unlike my current leak.
Mazda - Protege :: Little Hesitation And Jerkiness During Acceleration
Started my car yesterday and as I was accelerating, it made a very loud noise. It sounds like normal engine acceleration noise, only ten times louder. It was present whenever I accelerated, but not when I was coasting or idling, and not when the car was in neutral. (It's a stick shift.) During acceleration, there was a little hesitation and a little jerkiness, but not horrible. The problem came on suddenly - no problems with the car before yesterday.
View 4 RepliesMazda - Protege :: Generator Or Alternator Same Thing?
My Mazda 1996 Protege appears to have no alternator, but there is something called a generator. Are they the same thing?
View 19 RepliesMazda - Protege :: Dashboard Lights Cutting Out
Here's a quandary for those who know more than I do:
I have a 2000 Mazda Protege with 182,000 miles on it. On occasion my dashboard lights (and radio, for that matter) cut out, going completely dark. Now here's the kicker: If I give the dashboard a little tap with my hand, everything comes back all glowing and lit.
My fear had been the alternator was going bad (Again!), but since it seems to be coming back with a bop on the dashboard...is this just a loose ground? What should I be looking for? Is this something a novice like myself could be taking care of, or where should I be directing my mechanic?
Mazda - Protege :: 2003 - CEL Came On Again / Engine Without Motor Oil?
I have a 2003 Mazda Protege. I had the check engine light come on and took it to my local repair shop. They diagnosed it as a bad oxygen sensor. They replaced it, but a week later, the light came back on. So, I decided to take it to the dreaded dealership and pay for their "expertise". They informed me that the light was a result of a intake hose with a hole in it. They also told me that the vehicle's oil pan was rusty and needed to be replaced. The vehicle did not leak oil. After a week of driving, I noticed spots of oil on my driveway. I checked the oil and it was low, so I decided to have it towed back to the dealership to have it checked out. I assumed it was the oil pan that had not been installed properly.
Today, the service tech informed me that my engine was blown and needed to be replaced. He told me that this cam warped and didn't leak before because the pressure was being release through the rusty oil pan. This sounds absurd to me. It seems to me that what has happened is their responsibility. What could have caused this? A co-worker suggested that more than likely the mechanic could have made a mistake and started the engine without motor oil either after the oil pan was replaced or after the vehicle sat overnight and the oil drained out. Does this seem more logical? If the dealership is at fault, but will not fix it, what can I do?
Mazda - Protege :: Stalling But Would Never Loose All The Power
I was driving my car on the highway, stopped to get gas and it started stalling but would never loose all the power. The check engine light did not go on. They have replaced spark plugs, hoses and it keeps doing the same, they told me there could be water in the fuel i pumped so i burned through the gas, drove 5 hours back home and when going uphill i would give it gas the rpms would go but no speed.
I took it to the ford/mazda dealership in town and said that the codes it was giving em they could not decipher, their best guess was a timing belt issue, they suggested i took it to an exclusive mazda dealership...but the closest one is 3 hrs away. They said it wasn't my transmission. There is no set speed when it stalls..it does it often maybe every 20 seconds or so...the car is a mazda protege 2000 with about 140000 miles...
Mazda - Protege :: 2001 - Getting Code P0421
I have sel code of P0421. What are the odds of the downstream sensor being bad vs a bad catalyst converter? The car runs great and I get 19+ mpg in town driving. It is a 2001 Mazda Protege, 2.0L V4 .....
View 15 RepliesMazda - Protege :: 1998 - Won't Start At Cold?
I have a 1998 Mazda Protege LX 1.5 L 4 Cylinder and i have been having some starting issues, and stalling at stop lights.
To be clear i have replaced/cleaned, Injectors, Spark Plugs, Spark Plug Wires, Distributor Cap, Distributor Coil, Air Filter, Cleaned MAF, Cleaned the EGR Valve,
My car won't start in the morning, just gives cranks but if I press gas pedal it starts and have to keep it until engine gets hot enough. then it works till the car cools down again, and repeat the problem in the morning when I have to go to work. When the car is warm it starts fine but has idle issues regardless of temperature. As usual when the engine is cold or cool, it won't start.
Visited 2 different mechanic shops and the problem still exist, I don't know how and what they did it, it only worked for couple of months and the engine noise was bit high, I believe he just increased the idle, When i am at stop lights it has a rough idle and tries to die, When it idles it idles rough, Every once in a while I get a CEL Cylinder Misfire on cylinder 4. I'm confused on want to do , Don't know what else to do and its getting tiring, The car also feels like a lack of power.
Mazda - Protege :: 2002 - Won't Accelerate Properly?
I own a automatic 2002 Mazda Protege with about 167,000 miles on it. The other day I was at a stop light and when I accelerated it felt like the car was taking longer than normal to get into gear. I am scared that it may be a transmission problem.
View 2 RepliesMazda - Protege :: 2000 - Idle Roughly - CEL Comes On?
I have a 2000 Mazda Protege ES (1.8L) with 120k+ miles and an automatic transmission. The car drives well at speed, but when sitting at stops it will shake a little, sometimes worse than others. Often the RPMs drop to below the lowest tick for a split second before recovering, very much like when driving a manual transmission and not pressing the clutch in enough. Even when the RPMs are steady at a stop, it shakes enough to rattle a couple of the plastic parts in the dashboard.
Recent history (some likely unrelated, but I'm no expert):New air hose (one from the air filter to the engine) in September. RPMs were falling at idle more often than they are now, there was a decent sized crack in the hose. RPMs stopped falling as often, but has idled roughly before and after.New radiator and thermostat in April (overheated on the interstate and cracked open).New spark plugs and wires last fall after one cylinder wasn't firing.For the last couple years every fall when it starts to get cold, the alternator belt squeaks and I tighten the bolt a little each morning until it stops (usually after 2 days, maybe 3 - the alternator itself is on a long bolt that adjusts the belt tension).Every 5k miles I have the oil changed with high mileage oil and tires rotated/balanced.
I took it to a garage a couple weekends ago after the check engine light had come on earlier in the week. I reset the computer and the light never came back on, so I lost the chance to have the code read, but there weren't any other symptoms beyond what I'm used to. The mechanics at the shop said they couldn't find anything specific causing the rough idle and suggested replacing some or all of the motor mounts, which are weak. They didn't seem confident that would fix the problem, and neither am I, as I don't see how weak motor mounts would explain the low RPMs as well as the shaking.
Mazda :: Drive Shaft Stuck On 1998 Protege
I've managed to remove 95% of my driver's side drive shaft but can't for the life of me remove the spline from the transmission. I cut the boot so all there is is the cup with the spline plugged into the gear box. I've pried and pried with a screwdriver and drove a chisel with a hammer in between the cup (not sure the proper term for it) and it wouldn't budge. I'm going to try and track down a puller that will work on this car but that might take days or weeks. I have to work tomorrow night so my question: Will it do any harm to the transmission or be unsafe to drive with only one drive shaft?
View 19 RepliesMazda - Protege :: P0421 Error On 2001 LX 2.0 4 Cylinder
Would hitting the upper catalytic converter with a rubber mallet free up anything that may be causing the P0421 error and CEL to come on? I need to know if it would do any good or any harm.
View 7 Replies