Mazda - Protege :: 2003 - Stalls At Start Up When Warm Up?
I have a 2003 Mazdaspeed Protege that is having a stalling problem. The motor has about 30k miles on the block with around 3k miles on the internal components (rods, pistons, cams, etc.). Cylinders were bored 20 over and head was machined.
This stalling, or almost stalling, problem occurs when I start the car after it's been warm for awhile. For example, if I were to drive for an hour, park it for 45 minutes, and then come back out to start it up. It'll fire up, drop to idle, and then the idle will dip, stalling 50% of the time. The rough idle lasts anywhere from 5 to 20 seconds, and then usually fixes itself.
Giving it some gas does nothing to alleviate the problem; sometimes making it worse. Cleaning the idle air control valve solved this for a few days, and then it was back to its old ways. These symptoms do not occur on cold starts or if I restart the car after 5 or 10 minutes of it sitting. We couldn't find any vacuum leaks and there are no codes being displayed.
Nissan - Sentra :: 1987 - Idles Real Rough At Times / Hesitates At Stop Signs / About Stalls Out When Press Gas Pedal To Go
I have a 1987 automatic Nissan Sentra XE- two barrel carburetor, mileage 212,880. The car has one major problem that is going to get me hit driving it in rush hour. Most mechanics will not touch the car due to being carburetor.
Let me explain: the car idles real rough at times, hesitates at stop signs and red lights, about stalls out on me when I press the gas pedal to go or when I start to make a left or right turn. However, other times the car has little to no hesitation and idles perfectly. I have not been able to come up with a good a pattern with this problem.
I have replaced, fuel pump & filter, spark plug wires, coil, distributor, ecu computer, ran sea foam through the fuel system and have replaced many vacuum hoses.
Ford - Escort :: 1999 - Rough Start / Couple Of Hiccups But Runs And Idles Fine
I have a 1999 Ford Escort SE wagon with 112k miles on it. Last week when leaving work my car started very rough. This was unusual so I killed and restarted the car about three times before letting it run it's course (~30 seconds), after which the car ran fine. About a week later on my way to work the car seemed to 'sputter' (for lack of a better word) when I pushed down on the petal looking for some power on two separate occasions. On each side of the sputters the car seemed to respond fine, but when it did sputter there was a severe lack of power. I got to and from work just fine, but while letting the car idle in the parking spot of my apartment for a minute before shutting off the engine the check engine light finally came on. The following morning the car again started rough (as if it were misfiring/running on 3 of 4 cylinders) and this time it took a good minute before smoothing out. However, after the car smoothed out I experienced no issues on the way to work, no sputtering, no loss of power, nothing. Doing some initial online research I feel that the problem may be one (or more) of the following:
-Fuel pump
-Vacuum lines
-O2 Sensor
-Spark plugs (they are original)
-Fuel Filter (it is actually past due for replacement)
I plan on getting this checked out ASAP, but that still may be 2ish weeks away with my schedule. Some similar reports say that I may be having a 'lean mixture' issue (not getting enough fuel), but I haven't had the time to check the code. My question is, how "safe" is it to continue driving my car with the current situation? Is it at a super high risk of failure/random stalling during rush hour? Will it cause any damage to the engine if there is a cylinder misfire upon start up? I was also wondering if the car would be reasonably reliable to drive on a ~400 mile road trip on an upcoming weekend, but I am making plans as if it is not.
Additional Details:-Tried charging the fuel lines (car to 'ON' then 'OFF' position 3-4 times), had no effect on the morning start-up-Commute to/from work is about 20 miles
Ford F-150 (2004-2008) :: 2007 - Idles Rough And Stalls Occur Often When Start
I have a 2007 Ford F-150 5.4l v8...
Codes
P0012 int cam position timing over ret bank 1
P0022 int cam position timing over ret bank 2
P0300 random Missfire detected
P0316 engine misfire detected on start up
P0340 cam position sensor curcuit fault
P0345 cmp sensor a circuit problem bank 2
Starts rough, idles rough and stalls occur often when start, after it runs for 5 minutes and sometimes dint starts at all. I replaced spark plugs, coils, cam shaft sensors and had oil changes done and. No effect.
Oldsmobile - Leaks - Cutlassciera :: 1994 V6 Idles Rough And Usually Stalls If Put It In Gear When Start The Engine
I have a 94 Oldsmobile Cutlass Ciera, (3.1L V6 GM3100 engine). When I start the engine it idles very rough and usually stalls if I put it in gear. Eventually once it warms up I can drive it, but when I do drive it's extremely sluggish on accelerations and acts like its about to die. At constant speeds it runs mostly ok. We figured it was a vacuum leak, but we've tried every test we can think of to find it and talked to a couple mechanics and tried their tests and it passed all of them. Supposing it isn't a vacuum leak, then what it might be?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: After Start Up RPMs Drop - Stalls Out Then Idles Rough?
2003 7.3 excursion.. The truck starts every time revs up and idles about 3 seconds then the rpms drop and it tries to stall out catches itself then revs backup and idles rough similar to if you have got air in the fuel lines from changing the fuel filter.. About 1 in five times the truck will stall out and it starts and immediately and idles rough but the rpms and everything runs at speed and rpms don't drop again! This is a reman engine/transmission recently installed.. The mechanic who installed it was unable to figure the problem out.
View 6 RepliesFord Ranger / B-Series :: 2003 4.0L Idles Fine But Stalls When Given Gas
I'm having a bit of trouble with my fathers '03 Ranger Edge 4.0L. It has about 100k miles on it, and we keep it very well maintained. This is the first major problem we've had with it.
When the problem first occured, it had been driven about 30 miles on the highway and about 5 miles after getting off the highway, he pulled up to an intersection and stopped. As he started accelerating again, it all of a sudden started sputtering, surging (almost exactly as if it were running out of gas), and then stalled. It continues to exhibit this behavior. It will start and idle fine, but struggle and then stall when given any amount of throttle. It's also an automatic transmission if that makes any difference.
Fast forward to this past week after we had it towed home. We have checked the fuel pressure, and its dead on at about 64psi. We changed the fuel filter, changed the PCV valve, changed the upstream O2 sensor, put in a new air filter, cleaned the MAF sensor, and cleaned the intake of the throttle body. We're now at a loss as to what could be causing the problem. The CEL is not on, and there are no codes being shown when we plugged it in. We also thought it may have been bad gas, so we drained the tank and put fresh gas in from our preferred station. The plugs and wires are also fairly new, only about 4k miles on them.
Are we missing anything here? What else we could try? The absolute last resort is taking it to a shop, we're going through a rough patch with finances.
Mazda - Protege :: 2001 - Stuck Gas Pedal / Making Noise When Pushed Harder
Lately, when first starting my car and after it’s been sitting for a while the gas pedal seems to be stuck.
When I push on it slightly it doesn’t move; but if I push a little harder it will make a noise and become free and movable. No further problems until it sits for a while or the next morning. Then the same stuck pedal. Exert a little pressure and it frees up.
I tried squirting WD40 on the linkage but it does no good. What could cause it to bind up? 2001 Mazda Protege LX 2.0 ....
Mazda - Protege :: 1994 - Brake Pedal High And Hard And No Response When Depressed
A couple weeks ago the front brakes were done on the Mazda. Then the wheel bearings needed to be done. I think the shop outsourced what I guess was the packing of the bearings. I paid for the work, and drove away, nearly, but didn't because I had no brakes and there I was pulling out into 5:00 PM traffic. The emergency brake saved me. I walked back into the shop and they discovered the power brake booster had broken. I wonder, because if you drove the Mazda to park it in the shop lot where the customers pick up the vehicles after repairs are made, wouldn't you notice that there is no braking action. The brake pedal was high and hard and there was literally no response when I depressed it.
The shop keeper said, darn I guess I'll have to replace this, meaning pay for it, since it (may have) happened when the bearings were being worked on. My question is, is there any reason why working on bearings might end up breaking the brake booster? Chances are, it was just coincidence, right? or? I don't know. Because the car is old, he had to take several days to find the part. Anyway, he sent me off and told me to drive it carefully. The drive home was absolutely nervewracking and required continual tugging up on the emergency brake stick. I wonder if they despise my car so much now that they are sending me off to drive in it in such an unsafe condition. Anyway, hoping it will be fixed tomorrow. But my question still is ... would working on bearings possibly be cause for breaking the brake booster?
F Series :: 1982 F150 Truck Starts And Idles Just Fine But Stalls At Stops
Today I acquired a 1982 F150 with a 302 engine, 4 brl. Edelbrock carb. The truck starts and idles just fine, but when I come to a stop, try to give it gas to go it dies. It starts right back up, and I have to rev it high a couple of times then put it in gear and it will finally go. When I got it home I let it idle a few minutes and tried playing with the air and fuel mix but don't know what I'm doing, really. It seems I can hear a hiss, and when I was reaching for the air/fuel screws I got a little shock on the hand from the distributor. We want to use this truck as a farm truck, and plan to get a manual for it, but what might I might check for the cause of it stalling.
View 1 RepliesRough - Mazda - 626 :: 1999 - Rough Idling But Runs Fine At Higher RPM
This problem has been getting worse over the last 2 years. When the car starts it idles fine at about 1000 RPM. As soon as it warms up, it starts to idle rough, between 500 and 750 RPM. It almost quits running. As soon as you give the car some gas it runs just fine. About 3 weeks ago I got a "Engine Lean" check engine light error. I reset the system and have not gotten the error again. Since then I have: changed the MAF cleaned the EGR (made sure it closes completely and ohm out the coils in the actuator) changed the O2 meter on the exhaust manifold cleaned out the throttle body Ohmed out the air idle controller. What I should check next. I was planning to check the fuel pressure in case it is a fuel system problem. It is a 1999 ....
View 5 RepliesMazda - Protege :: 1996 - Rough Idle When Step On Brake At A Red Light
I have a 96 Mazda Protege DX. 1.5L engine, now with 161,000 miles. 5 speed manual transmission. I had it for 7 years. Originally bought it for $1900 with 121,000 miles.
This has been a problem for about 5 years. When I am at a red light or idling and I step on the brake, my idle gets rough and my engine feels like it is about to turn off. The idle does not bounce up and down. It just goes down to 400-500rpm from the normal 800-950rpm range.
Again, this only happens when I step on the brake while the car is not moving. It does not seem to happen when I coast in neutral and hit the brake to slow down. I raised the idle a bit, but it still does it. I could not find any vacuum leak around the brake booster and I know the brake booster works because I pumped my brakes while the car was off, and when I turn the car on, the brakes soften up.
Also, my brakes feel weak. I usually hit the brakes nearly to the floor board to stop the car. New pads, rotors are good. Brake fluid is at right level. Mechanics say nothing is wrong with my brakes.
Secondly, my belts screech at every start up. Lasts anywhere from 3-20 seconds. This has been happening for the entire 7 years I have owned the car. Mechanics replaced the serpentine belts twice in that time. Replaced a pulley and A/C compressor. I tried using WD40 but it doesn't effect it. Mechanics tell me that the belt tension is correct and they do not know why it still screeches.
Mazda - Protege :: 1992 - Check Engine Light Coming On - Rough And Sputter
I drive a 1992 Mazda Protege. Recently had an oil change and put in new air filter. Recently the check engine light has been coming on. Sometimes it will run rough and sputter a bit when the light flips on and then runs normal after the light flips off, sometimes it seems to run fine when the light comes on, but the light does go off and the car runs fine after it has been running for a few minutes. Shortly before I had my air filter and oil changed I did have an incident at a stop light where the car died and did not restart for a full five minutes, at which point it sputtered for a bit and then got me home.
I took into the local mazda service center and dealer (they were the only ones who had the right kind of connector to pull the error of a car this old), and they said the only code coming up was a p69 which indicated a bad thermoswitch. I have already paid for it but the parts won't be in until Saturday. I have until then to cancel the repair and just pay restock and the original diagnostic fees. Should I go through with this repair, or do the symptoms described indicate something else?
Mazda - Protege - Smells - Sparkplugs :: 1990 - Rough Idle Stutter While Accelerating?
1990 Mazda Protege with a 1.8L DOHC, manual 5-spd transmission, ~173K miles on it. On my way home the other day, the car ABRUPTLY started to run very rough - with what I would call repetitive and incessant stuttering when accelerating (though I am by no means technical with respect to cars). I shut the car down, hoped the problem would go away, but when I started it up later that day, the problem was still there - the car BOTH idles rough and doesn't accelerate very smoothy. When I come to a stop, the car feels as if it's going to stall but stays running. This afternoon, I took it out on the road for ~3 mile drive (up to ~ 50 mph) and the problem is the same - but I did also notice, when driving, that the car gave off a smell reminiscent of firecrackers - perhaps a sulfur-ish smell. I googled the issues I was having and I got a whole array of problems - ranging from simply bad spark plug wires (which have been replaced in the past 1.5 years) to a stuck EGR valve .
Here's some additional info on my car: -Was just in the shop 2wks ago for overheating - found the thermostat to be bad - they replaced it and I no longer have the overheating issue. While there, they also replaced the belts for the alternator and water pump (Which had been squealing for quite some time) -Spark plug wires and distributor cap were both replaced in the last 1.5 years -Last oil change was > 6 months (but less than 3000 miles) ago - all the fluid levels seem to be fine -Though I think it is unrelated, the car is also making a high pitched squeaking noise emanating from the R front of the car while driving - I suspect this is the suspension-related as the shop informed me that I have one front stablizer link broken while the other is loose (and when I push down on the R-front side of car while it is not running it yields a similar squeaking noise.
Prius (2004-09) :: Starts Fine But Idles A Little Rough
Just recently my Prius Taxi with 340,000+Km has developed a little problem,it starts fine but after 20-30 seconds it begins to feel like it's not running properly on all four cylinders,if i go to the exhaust pipe it seems like it's spluttering slightly.
Yesterday I changed the plugs,checked air filter and all connections,everything fine, when I accelerate it feels hesitant but after the car gets up to temp it seems to go away,it only happens when i start it first thing or if it's been left for a few hours, it's never had the throttle body cleaned and I'm wondering if what I'm describing is a symptom of this?
Mazda - Protege :: 1999 - Won't Start When Hot
I have a 1999 Mazda Protege. As of last summer it started giving me problems with not wanting to start after I had driven it around town for a little while. (IE: to the grocery store, to the bank and then to my sister's house. It wouldn't give me the same problem if I just went to the grocery store and back home. It would start up fine and I'd be on my way. Only when I went somewhere and shut it off then repeated that a couple more times.) I took it to a mechanic who wholeheartedly believed it was the coil packs not allowing my car to function properly.
So we replaced those and everything seemed on the up and up. (Keep in mind that this was towards the end of summer and the temperature was dropping.) The car was perfect all throughout the fall and winter, but now that the temperature outside is starting to rise again it's beginning to do the same thing it did last summer. I don't want to take it to another mechanic that's going to have me dish out an extravagant amount of money again only for the problem to persist.
Mazda - Protege :: 1998 - Won't Start At Cold?
I have a 1998 Mazda Protege LX 1.5 L 4 Cylinder and i have been having some starting issues, and stalling at stop lights.
To be clear i have replaced/cleaned, Injectors, Spark Plugs, Spark Plug Wires, Distributor Cap, Distributor Coil, Air Filter, Cleaned MAF, Cleaned the EGR Valve,
My car won't start in the morning, just gives cranks but if I press gas pedal it starts and have to keep it until engine gets hot enough. then it works till the car cools down again, and repeat the problem in the morning when I have to go to work. When the car is warm it starts fine but has idle issues regardless of temperature. As usual when the engine is cold or cool, it won't start.
Visited 2 different mechanic shops and the problem still exist, I don't know how and what they did it, it only worked for couple of months and the engine noise was bit high, I believe he just increased the idle, When i am at stop lights it has a rough idle and tries to die, When it idles it idles rough, Every once in a while I get a CEL Cylinder Misfire on cylinder 4. I'm confused on want to do , Don't know what else to do and its getting tiring, The car also feels like a lack of power.
LS / MKZ :: 2002 Lincoln Idles Rough On Cold Mornings But Runs Fine
The car idles rough on cold mornings but runs fine. It will stall while idling but starts back easily. I am getting a 1131 and a 1151 code with my scanner along with 0300 and lean bank 1 codes. I started having these problems after I had to remove the upper intake to replace coil packs. I was getting egr code and had an egr port completely block off but cleaned that out and no longer get the egr codes. Spraying carb cleaner around the engine I get a very slight bump in rpm around a couple of the intake ports could that be my problem or should I look deeper?
View 5 RepliesMazda - Protege :: 2000 Won't Start / Burned Rubber Smell
I think I broke my car. I just bought this car a few months ago and all seemed well. I bought new tires, changed the oil, had the brakes inspected, you know the things daddy's tell their daughters to always be sure of. I have had no problems with the car till last weekend. My boyfriend and I got into an argument, long story short I sped off, using his words "hot rod style".
I smelt burned rubber (not so new tires anymore) but I figured it was just that. When I got back home my boyfriend said that he smelt something burning under the hood. No smoke or fire just a burning odor. The next morning my car wouldn't start. We jumped it and it ran just fine. Did the errands for the day no problem.The next morning it wouldn't turn on again, this time when we jumped it, it just wouldn't start. I have checked the battery at AutoZone and they said it was fine. the fuses are all good as well.