Ford Super Duty (1999-2016) :: Transmission Shifting From 3 To 4 Gear Seems To Be A Bit Prolonged
I have a 2012 F-250 ccsb lariat and the shift from 3 to 4 seems to be a bit prolonged as if the converter is slipping and wont go ahead and push it into 4 gear. Also it will want to downshift from 3 to 1 and feels like the car behind nailed you. I have read that the early 2011 had some of this problem and the dealer reflashed the tcm and it did not do much good but as mine being a 2012 mine should have been flashed with the lastest tcm flash from the get go?? Egr fell off and am running Kory Willis tunes through ez lynk so the stealership is probably out of the question. I have also read that changing a couple solenoids( dont remember which ones) will fix the problem.
View 11 RepliesFord Super Duty (1999-2016) :: Transmission Shifting Hard Between 2 And 3 Gear
The tranny is shifting really hard between 2 and 3 if I feather the throttle it can be a little less of a jolt but still enough none the less iv never done a filter and fluid change as I just got it it has 235000 miles 99 v10 super duty 4x4....
View 8 RepliesFord Super Duty (1999-2016) :: Transmission Slip In 1st Gear And Reverse?
Drove the wife to work this morning. The turn off into town there was a lady stuck so I pulled over in the drifts. After putting in back in gear I had to get on it to get out of the drifts. Snow was blowing over the windshield, and I imagine throughout the engine bay.
After that it felt like it stayed in 2/3rd gear. I'd hit the pedal and it would redline and sort of accelerate jumping in and out of gears. So i slowed down to a stop. Accelerated slow and it was ok but when I got more on the pedal it would feel like it was slipping. Once I got in the driveway, she idled for about 15 mins while I shoveled out my spot. Once putting in gear again I had to rev it up for it to move.
Also reverse, had to rev it up to move it.
Ford Super Duty (1999-2016) :: Losing Power In Reverse / Transmission Not Always Going Into Last Gear On Interstate - Code PO741
I have been having trouble with my 2008 Ford F250 4x4, 6.4 liter diesel transmission. SCT tuner, 10" lift, egg delete and dp delete has been done. I have been losing power mainly in reverse but have noticed that the transmission hasn't always been going into the last gear on the interstate. Code PO741 would come up. The other day the shifter was stuck. So I played with it and found that the cable on the transmission had fallen off. After replacing it. The transmission wouldn't go into reverse but has been doing semi good in forward. Well I have been limping it around until today when I was going down the road and it completely stopped pulling. Now no matter what gear I place it in, it will on go in reverse. What could be causing these issues or where to even begin to start looking?
View 3 RepliesFord Super Duty (1999-2016) :: 2011 - Hesitates While Shifting Into Reverse?
I have a 2011 super duty with the 6.2 flex. When shifting into reverse, it hesitates, then slams into reverse. Same on the lower gears when driving. This doesn't occur all the time, but the majority. Been talking to a couple other super duty owners (diesel owners) who have been having the same prob, but not as severe. We all have noticed the prob after having charcoal filter replaced. Is this a tranny issue or computer issue?
View 3 RepliesFord Super Duty (1999-2016) :: Grinds Bad Shifting Into 3rd Gear
I have a 99 7.3 F350 with 5 speed manual with over 300,000 miles. Grinds bad shifting into 3rd, and nothing happens in 4th. I think it is a S5-47-ZF. Is a 6 speed manual comparable to bolt up to bell housing?
View 2 RepliesFord Super Duty (1999-2016) :: Strange Hesitation When Shifting From 1st To 2nd Gear
I bought my 2011 F250 FX4 about 2 months ago. A little about the truck: 6.2 liter gas. XL FX4. Manual 4x4. 6 speed auto. Supercab. Long bed. 42,000 miles. (1,000 of them mine.)
Until yesterday, the truck has performed absolutely flawlessly under all conditions. Then, randomly, I had what felt like a "missed shift" as I was leaving my dog's veteranarian yesterday. I pulled out onto the highway and as the truck attempted to shift into second gear, it didn't "catch" second. The gas just revved up and I had to take my foot off the gas pedal and put it back down to get second gear to engage. Most of my driving is stop and go around town and this has only happened once in probably well over a thousand stop and go situations. Should I be worried or was it just a fluke?
Also, FWIW, I did plenty of stop and go driving today without a single problem.
Ford Super Duty (1999-2016) :: Massive Clunk Sound When Shifting From Reverse To Drive Or Vice Versa
I continuously read that people with 6.2 F250s averaging 13 mpg or so in a combination city/highway driving. This 2014 4x4 barely has enough power to move itself (honestly, I'd rather have my Ram 1500 back) and barely gets 10mpg. Basically have to give it about half-pedal to even get up to freeway speed and floor it if i want to pass anything. Is it just that much of a POS or does this not sound right? Other than a massive "clunk" sound when shifting from reverse to drive or vice versa, no indication of any problems.
View 14 RepliesFord Super Duty (1999-2016) :: 4r100 Transmission Shifting Hard
Recently I have had an issue with my auto which was just rebuilt. About 500 kays after i picked it up it shifts dangerously hard and immediately into all gears at around 20-40 mph, converter also locks immediately. The speed sensor in the box was replaced with the rebuild but I'm having it replaced again this thursday just in case.
Just for the record I cooked it on the beach a while back, the speed sensor was replaced with the rebuild as it was doing the above, the od light also flashes when this occurs, before and after the rebuild.
Prior to cooking it never had an issue.
What could be causing it? I'm starting to worry it cant be fixed, have done a google and tried a couple of things mentioned. Code says wiring issue associated with speed sensor in box.
Ford Super Duty (1999-2016) :: 2002 F250 - Transmission Shifting Hard
I have a 2002 ford f250 with the 7.3l diesel. I recently installed a ts performance chip. On my pcm. And after i first tried all the different stages I didn't like how my transmission was shifting hard. So I contacted the manufacturer and he told me they could reprogram the chip for smoother shifting. So I removed the pcm and removed the chip. But when I went to reinstall the pcm I bent one of the pins on the pcm some how.
So I took it back out and straightened the pin with pliers . i reinstalled it back in the truck. Only to find when I reattached the battery cable I have no power to anything ignition ,horn, lights,Cigarette lighter etc. So my question is if the pcm is bad, or not contacting properly due to the pin being messed up. would that have anything to do with the lights and horn and all that? I suspect its the gem bsm or Vsm. Whichever one my truck has. But really not sure because everything worked fine just 20 min b4.
Ford Super Duty (1999-2016) :: 2011 F350 - Transmission Shifting Hard From 3 To 4 Going Up And 2 To 1 Going Down
I have a 2011 F-350 6.2L that has extremely hard shifts from 3 to 4 going up and 2 to 1 going down. Sometimes on downshifts it feels like something has ran into the back of the truck. I had the computer updated when the truck had approximately 40,000 miles on it and he assisted a little bit. The truck now has 140,000 miles and it is back to shifting horribly. I put it in the shop at the dealer on 30 December 2013. The dealer says that the problem is that the shift solenoids need to be replaced but that they are not available. The truck is still sitting at the dealer and I am being told that the parts should be available mid February.
View 10 RepliesFord Super Duty (1999-2016) :: F350 - Transmission Won't Go Forward But Has Reverse?
It seems its the 4R100 tranny non pto of course and 2wd version. I drove down the rd. after bleeding the brakes, new caliper front right, came home let it idle for about 10 min, shut her down. Went to move it about an hour later, it went into reverse no problem, then when put it in Drive it revved like it was in neutral. There was no banging, no clunking, nothing to make it seem like something catastrophic happened.
I then did a line pressure test and Reverse was fine 200 psi for sure, in drive mode however it was low like around 50 but had to rev real high to get it to 150 like 3/4 pedal and it would want to seem to go forward at a crawl but nothing more. Next I did the obvious and cheked the fluid, it was about 1/4 quart low so added a bit. The fluid did not stink and was beautiful red like new.
I then tried again... no dice same scenario. Then took off the pan, no metal chunks and virtually no dust on the magnet??? Ok so I figure maybe something with the shift valves? Took them all off and the accumulators as well, all check ***** were in place and all valves moved freely.
Now onto the the solenoid pack, checked all per manual for ohms and all were perfect reads at about 27 Ohms, except the EPC solenoid that is the big one on the pack, it should read about 3-5 ohms but this guy is about 12.5 ohms.
I spoke to a tranny shop in town and they said it would not be the EPC and that I could "unplug" the solenoid pack and It would still move forward without it but not to drive like this as line pressure would skyrocket?
Why this thing would have 200 lbs pressure for reverse and so little for forward I mean? that should mean that the pump is working great, if there was a broken something metal I figured I would hear something rubbing or banging or see some shavings? Can this be a "worn out" valve? or gasket issue?
Ford Super Duty (1999-2016) :: Transmission Not Shifting Into Tow Mode When Pulling To A Steep Hill
I have a 2006 f-250 super duty with a 6.0 and auto trans. I was pulling a trailer with about 5k of vehicle on the trailer.
Problem : after a long trip on good roads, I had to pull a steep hill. climbing the hill i did not shift into tow mode and all of a sudden my engine raced up to about 3k rpms and seemed to either shift to low or ( maybe ?) the Governor may engaged ?
Anyway I made it to the top of the grade and it seemed to be fine from there.
Question Is the trans broken, or did the computer maybe try to protect the trans ? It seems to work fine still?
Ford Super Duty (1999-2016) :: Transmission Will Not Engage In Drive Or Reverse After Replacement
I have a 1999 F250 super duty that blew a front seal on the transmission two weeks ago. I sent it to a shop and they replaced the seal, and torque converter. However when they put it back in it will not engage in drive or reverse. After working on it several days we replaced the transmission with another one from a service company. This replacement came with a 90 day warranty. However once it was installed it does the same thing and will not engage in drive, or reverse. I am not sure what is going on but with two doing the same thing it makes me thing maybe electrical or something else.
View 1 RepliesFord Super Duty (1999-2016) :: Rear End Chatter In Reverse - Damage In Gear Head?
Ok, I've seen a post or two about this issue of rear end chatter on the super duty But not that many so I am going to ask a question here and now......what causes/allows this to happen and what purpose does it serve? also, does it cause any damage to the gear head? or any other part of the rear end?
My truck tends to do this from time to time when I am plowing snow (only when backing up, or at least so far) and I really can't relate it to condition other than maybe the fact that pushing snow may cause the gear oil to get hotter than normal driving and thins out and causes this?
Ford Super Duty (1999-2016) :: 2010 F350 - Reverse Gear Signal Wire
I installed a reverse camera to my new Pioneer in-dash nav head unit this morning. I wired (at the rear of the truck) the power signal lead to the reverse wire at the trailer connector. I also need to wire a reverse signal input into the back of the head unit. I really do not want to run a power lead from the rear of the truck to the cab. Is there a wire under the dash I can tap into, or could I use the wire going to the backup alarm that’s somewhere under the dash (if I can find it). 2010 F350 deisel, crew cab, 4WD, long bed.
View 9 RepliesFord Super Duty (1999-2016) :: Clutch Slipping - Harsh Shifting - Loud Clunk Noise Into Gear 2 Then 1
New truck 11000kms ago thats done medium amount of work but nothing heavy or sustained for long periods of time. I get the feeling of clutches slipping especially when truck is cold but also when normal temps. Doesnt make any weird noises or anything. I can really notice the difference in torque if in manual mode being much better, but still not perfect if i stomp on the gas pedal and go through the gears in manual mode will still slip. Also is really harsh shift if i come to a halt in 3rd manual mode with the brake pedal depressed push minus button the truck makes very loud clunk noise into gear 2 then 1. Took it to ford they couldnt find anything ? Thinking of trying another dealer.
View 2 RepliesFord Super Duty (1999-2016) :: 2001 - F250 V10 Transmission Malfunction - Only Goes Into Park / Reverse?
I have a 2001 F250 V10,
So the truck drove fine yesterday had zero issues... I used my auto start as I do every morning in this cold weather, get into the truck and shift from park to drive and its like it does nothing. I can free rev in N,D,1,2. Reverse works great.
I tried switching from 4wd to 2wd, no change. Reverse works just fine. No noises, codes or anything, just doesn't want to engage...
I am assuming I have a 4R100. Could something electrical cause this? I am thinking its mechanical, but hoping someone has ran into this before.
Literally no way I would have known the trans was going bad... It's always worked fine. Tranny fluid is full, I tried unplugging the battery waiting and plugging back in, no dice.
Ford Super Duty (1999-2016) :: Screeching Sound Only Happens When In Gear (auto) Moving Forward Or In Reverse
My 2001 F250 5.4 has started to make a screeching sound. It only happens when it is in gear (auto) moving forwards or in reverse, and increases in pitch relative to engine speed rather than road speed, and is much more noticeable under mild to moderate acceleration. Maybe I actually mean transmission input speed?
When simply maintaining road speed, it is almost silent. Anyway, if I drop it into neutral while driving, the sound stops, and starts again when I put it back into gear.
From the drivers seat and with the windows closed, it sounds as though it is coming from the engine bay at steering column height, although this is really tough to gauge while actually looking where I am going. With windows open, it comes from both sides of the vehicle.
1st thought is tranny......
2nd thought is a water pump bearing, although there are no apparent cooling problems or leaks.
3rd thought is the alternator bearing, although there are no charging problems.
I say alternator because I recently changed the serpentine belt and noticed that the alternator made a very faint screech-like sound when spun without the belt on it. The main screech was there before I changed the belt. Maybe it gets really loud under load?
So I'm kinda scratching my bean and wondering what expensive piece of mechanics I'm going to shell out for next. If it's #2 or #3, I can do those myself, but if it's #1.... it likely means more money than I have to spare.
I did wonder about removing the serpentine belt and driving a very short distance (end of the driveway and back) to see if I can remove the pulleys, tensioner or other belt driven parts from the equation. Maybe this is not such a smart idea. I'm somewhat at a loss right now.