Chevrolet - Blazer :: Wheel Bearing Making Noise After Tire Replacement
Immediately after I had four new tires installed on a 2000 Blazer 4wd, the front wheel bearings started making noise. At the time I thought the noise was from the new tires. A few thousand miles later my mechanic told me I needed two reman hub assemblies (sealed bearings) for ~$350 apiece plus labor.
Is there anything that the tire shop (independent not chain) could have done (accidentally or otherwise) to damage the bearings during the tire installation? I have to get 4 tires for my 93 Chevrolet Caprice and don't wish to repeat the experience.
Whoops, forgot to mention this happened at 56k miles when the truck was five years old. Is it possible that the bearings were borderline and the process of mounting the wheels put them over the edge? For instance, someone being a little over enthusiastic with an impact wrench.
Prius (2010-12) :: Rear Hub / Bearing Assembly Replacement
I'm replacing the rear hub/bearing assembly on my 2010 Prius. It seems pretty straight forward. What is the correct torque for the 4 bolts holding it on? Also what is the correct torque for the 2 bolts holding the rear brake caliper on?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Axle Bearing And Hub Assembly Replacement
It's time to replace my axle bearing and hub assembly. Looking at RiffRaff site they show 3 different models. Early 99, fine course and course. I think I have the course thread but just want to make sure before I order. My truck is a L99 and I don't have the abs sensor. Looks like all 3 have come with the abs sensor. Do I simply not connect the sensor? Here's a pic of what i have. Course thread?
View 3 RepliesFord Excursion :: Changing Out Front Wheel Bearing Hub Assembly
This past week I changed out the front wheel bearing hub assemblys on both sides. I'm curious if completely disassembled one of the units? If so what did you use to get the large nut with the 4 notches in it off?
View 2 RepliesSebring - Chrysler :: 2004 - Stuck Wheel Bearing Assembly Removal?
I'm attempting to replace a front wheel bearing and hub assembly on a 2004 Chrysler Sebring. I've removed all the hub bolts and all other more external components. I've tried hammering the assembly, reinserting the bolts partially and hammering those, a slide hammer, liquid wrench...
View 9 RepliesFord Super Duty (1999-2016) :: Wheel Bearing / Hub Assembly Going Bad
How can you tell when your wheel bearing/hub assembly is going bad? I am hearing what sounds like "metal-on-metal" and I've already changed the brake pads, but the sound still persists. I was thinking about changing out the brake rotors since I did notice an inch long score on the rotor when I was replacing the pads. I don't want to spend a couple hundred dollars on rotors to find out it was my wheel bearing/hub assembly all along.
View 8 RepliesPrius (2004-09) :: Corrosion On Steering Knuckle Where Wheel Bearing Hub Assembly Seated
I have removed knuckle assembly and pressed out bearing hub assembly, I have the new bearing hub assembly..... I live in Iowa so there is corrosion on the knuckle assembly - I have removed enough that the new bearing assembly will go in....
My question/concern : With the corrosion removed the surface of the knuckle where the bearing will seat is not uniform all the way around. The bearing hub assembly will go in and will require pressure to do so but will the bearing last? I can buy a steering knuckle but do not want to if I don't have to.
Impala - Chevrolet :: 2008 - Ignition Switch Failure?
I am the (once) proud owner of a 2008 Chevrolet Impala. I have owned the car for one year, putting only 12,000 miles on it (was 109,000 when I bought it.) The car has run quite well—I have not had any problems out of it (unlike the 1999-2005 generation Impalas). But, as many of you may have heard, GM had some massive recalls as of late. Many of the cars have had fatal ignition switch failures. Basically every single Impala in the last (my) generation has been recalled.
Take any other keys/paraphernalia off of the chain—basically, just insert the key into the ignition, unattached to anything. This is the fix for the time being, apparently—until they can get ignition switches for however many hundred thousand Impalas they have to fix.
I am about to make a 3 hour drive. Now, that wouldn't be the longest drive that I have made in this car (and I cringe at the idea that, driving 17 hours with a bunch of crap hanging off of my chain, that my car easily could have been one of the unfortunate ones.)
Now that I know that I cannot be sure of the safety of my vehicle, I need to know what to do in the case of an emergency. I want to know what exactly the situation of an ignition switch failure entails...basically, what happens to my car and my ability to control the car. Lastly, I need to know what to do if this happens.
Santa Fe (CM - 2007-12) :: 2009 3.3l AWD - Wheel Bearing Failure
At 37000km we put new tires on and after about 1000km started to hear a high 'woo-woo-woo', from the rear, not really loud but a new noise. Guessing it might be tire noise I checked them for wear and thought the left rear was a bit sharp sliding your hand one direction but smooth sliding across the other way. Went for an alignment....it was only slightly off and the mechanic found the right rear wheel bearing was kaput.
It was done under warranty......but, do these vehicles are subject to premature bearing failure or was this a fluke? I did not see the bearing so I don't know if it was one of two or a pressed-on type or whatever. It would be nice to know that a wheel won't come flying off or seize up when we're halfway to nowhere if a bearing goes bad again.
Prius (Gen 3) :: Distinct Rotational Noise At About 30 To 40 MPH - Wheel Bearing Failure?
Since the Prius is my wife's primary car, I can go a long time without driving. I recently have been driving it more, and it seems to me that it has the sounds of a failing wheel bearing. Between about 30-40 MPH there seems to be a distinct rotational noise that sounds to me like a loud wheel bearing from the front end. The sound seems to get quieter as I go faster, and at 60 mph + it seems normal.
My wife didn't notice any difference, but she drives the car everyday so maybe she didn't notice the gradual increase in noise. I know it's not tire related, because I just swapped tires. When I did, I didn't feel any play in the front bearings or feel any roughness when the wheels were rotated.
Prius (2010-12) :: Rear Left Wheel Bearing Failure
At 46,400 miles of gentle driving, my left wheel bearing failed on my 2010 Prius, which was not covered by warranty because it is not 'drive train'. I was told there was nothing I did or could have done to cause this. I have had 4 Toyotas, two with over 200,000 miles, and never had this serious a repair (that wasn't my fault!). Am I being unreasonable to think this is unusual? I'm wondering if this car is going to continue to be a problem.
View 19 RepliesPassat (B5) :: New Front Axle Causing Wheel Bearing Failure?
I had a ripped drivers side CV boot and had my indy replace the axle with a new Raxle. ~200 miles after the replacement the wheel bearing on that side went south. I shugged it off and had it replaced. Well, after 200 miles on the new bearing, it has also failed (100 miles from home). I gotta believe the 2 bearing fails are related to the new axle, but I don't understand how!
View 2 RepliesPlymouth - Acclaim :: Clunk / Rattle Noise Coming From One Wheel - Catastrophic Bearing Failure
My girlfriend owns a '92 Plymouth Acclaim. We noticed a few weeks ago that there was a clunk/rattle noise coming from one wheel, and since it mostly happened while cornering, thought it might be CV joints or maybe suspension. She brought it to her mechanic who inspected the brakes and found that the rear shocks were bad, but sent her away without fixing anything. The other day, on a long drive, the rattle suddenly intensified, morphed into a loud grinding noise, and then the wheel fell off.
I think I'm going to have to confront the mechanic. The bearings apparently hadn't been repacked in some time, and were surely the cause of the rattle noise. I'm less concerned with the fact that he might have overlooked an obvious problem as much as neglected to properly service the vehicle.
Are brake techs supposed to check, then tighten wheel bearings or repack them if needed?
Venture :: ABS Light On After Wheel Bearing Replacement
I replaced the driver's side wheel bearing on my 2001 venture and now the ABS light goes on about 5 to 10 seconds after starting the car. It stays on through out the drive. Before the light goes on I get a sound as if passing your fingers up and down an old fashioned washboard. I have read throughout these threads to replace the bearing but I don't foresee that happening. How can this bearing be bad when the car feels great driving now.
View 13 RepliesSierra :: Wheel Bearing Hub Replacement / Integrated ABS Sensors
My 2005 GMC Sierra has just >80,000 kms on it, and I'm having to replace a second wheel bearing hub. A few months ago, the rear left wheel almost came off because the bearings were falling out of the hub. Yesterday, the same thing happened while traveling on a highway with the front left wheel. While my truck was being pulled up onto the tow truck, all the bearings fell out of the wheel - one was completely ground, the others were perfect. A few more turns or bumps and I suspect I would have lost the wheel.
I didn't have any grinding noises with the front tire (although I did with the rear) - the front hub deteriorated really quickly (within 100kms of driving), and it sounded like cables snapping while driving which was likely the bearings tumbling around.
Having problems with the GMC Sierra wheel bearing hubs/integrated ABS sensors? Should the hubs be wearing out so quickly? It seems like a safety hazard to me, since there wasn't any early warning signs of a major hub meltdown.
And I'm not sure if this has anything to do with it, but I've also had to have my rotors ground down 3 times and replaced once since new.
Camry :: Front Wheel Bearing Hub Replacement On 2007 SE
Just had an oil change and during inspection they noticed that the drivers side wheel bearing is starting to go. They brought me back in the shop and I was able to feel the play in the bearing myself. Only a matter of time before it needs to be replaced.
How to replace the front wheel bearing/hub assembly? I don't have a press for the bearing itself so I'm assuming I can just replace the entire hub assembly. I have already replaced the drivers side rear hub assembly about 1.5 years back due to a bad bearing
Prius (2004-09) :: ABS Light On After Wheel Bearing Replacement
My 2006 Prius with now 68,000 miles just had both front wheel bearings replaced today from an independent shop in town with a good reputation.
View 13 RepliesSonata NF (2006-10) :: ABS And ESC Off Lights On After Wheel Bearing Replacement
I have sonata 2006 v6 3.3. Over the weekend Left rear wheel bearing was replaced. Right after the replacement ABS + ESC OFF lights came on and stayed. I took the battery connection out and restart the car but no difference. There is no affect on driving or performance car drives normally, Cruise operation works normal as well. Mechanic scanned and scanner showed right real wheel sensor malfunction. He claimed that he didn't even open the right rear wheel. I am hoping it's not the sensor.
View 4 RepliesSonata NF (2006-10) :: Front Wheel Bearing Replacement
2006 Sonata with 90k ... When I make right turns the left front wheel is making a rubbing sound with the motion of the wheel. It's not doing it on a straight line, just turning right. I've talked to a couple of my friends and they are telling me it's a wheel bearing. I have a service manual but it's not really going into detail on what I'm in for. I work on motorcycles all the time and my good friend said he has a press if I can bring him the knuckle and the OEM bearing. Looking for a little guidance before I take the wheel off and get started. Are there any special tools involved, etc...should I do the other side while I'm doing this also...
View 11 Replies