Ford Ranger / B-Series :: 2003 Truck Idles A Little Rough - Code P1450
Where to start looking to resolve this code. It is not an intermittent code. It returns after about 3 to 4 key turns. Truck idles a little rough but runs fine. I have looked up the code and causes but wondering how to deal with this directly and fixed it. I'm wanting to sell my truck for something bigger and would like to solve the issue before hand. 2003 Ford Ranger Edge...
View 4 RepliesFord Ranger / B-Series :: 1999 - Rough Idles When Started / Have To Hold The Gas Till It Warms Up
Quick back story I bought a 1999 Ford Ranger It is a 4 cyl with an auto trans the guy said it had some trouble with the tranny (major understatement) he also forgot to mention he cut out the CAT. so running a 4 banger off the header.
When you start the truck it rough idles but you have to hold the gas down til it warms up. You can shift into reverse but it labors the motor and the motor will not up the rpms kinda stays at idle and wants to die no matter how hard you accelerate and you can't move up a slight incline.
When you shift into drive you have to rev the motor to 3 grand an it will catch then move slowly forward. no matter how high the revs go. The fluid levels are a tad above the full level and a bit dark for my liking.
Ok, I used an OBDII scan tool from the parts store and it came up with 3 codes P0351, P0352, P0500. From my internet search the first two seem to be coil related which explains why the motor is running like garbage. The last may or may not have to do with what the tranny is doing.
Ford Ranger / B-Series :: 1994 - Idles Rough / Stalls When Cold But Runs Great When Warm
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 RepliesFord - Ranger :: 2001 - Knocking And Smoking When Accelerate Uphill
About 3 weeks after an oil change, my 01 Ford Ranger started knocking and smoking when I accelerated up hills. I checked the oil levels to find that it was completely empty. Refilled the oil, but the problem persisted. Tried gas additive--nothing. Finally limped into the Ford dealership where they kept my car for 6 weeks trying to figure out what the problem was. After new plugs, wires, MAF sensor, coil, and PCM the problem seemed to be fixed...mostly. Knocking and smoking eventually stopped until I checked the oil levels again and it was empty. Added oil which started the symptoms all over again. Mechanic ruled out blown gasket. Claims knocking and smoking are unrelated (even though they happen at the same time 100% of the time). Smoke is white. Knocking (at its worst) sounds like a bolt rattling around in engine. Car does not lose power, and when I gun the engine it seems to go away. Only happens going up hills (of which Tennessee has plenty of).
View 4 RepliesFord Excursion :: Running Really Bad / Misfiring / Smoking And Sounding Real Rough
So Friday before last my ex laid down on me while i was headed to work. So I parked it in a walmart parking lot and caught a ride to work with a friend then had it towed home that evening. Problem i was having is it started running really bad, miss firing, smoking, and sounding real rough, but I wasn't getting any trouble codes. So after both uvch's, icp, ipr, icp pigtail, checking fuel for water contamination and pulling my hair out, i decided to check the oil and found it to be 4 quarts low. Talk about feel like a knuckle head.... While it was down it did receive a new water pump, a diesel site 203* thermostat, new billet thermostat housing, Gooch's Radiator Flush Procedure, and some fresh rotella etc.
View 5 RepliesFord Super Duty (1999-2016) :: F350 Started Smoking Really Bad And Run Very Rough
2007 f350. About 2 weeks ago my truck started smoking really bad, and I took it in to have it diagnosed. It was 4 injectors that were bad, so I had them replace all 8 and also install a bullet proof oil cooler. From the moment I got the truck back, it did not seem to idle as well as it used to, and over the next week, it began to blow a good amount of white smoke and run very rough.
But the weird thing is when I took it back to the shop to have it diagnosed, the minute I pulled into their driveway, it ran perfect, and they were unable to pull up anything. The next morning, I started my truck for work and as I drove down the street, the truck ran extremely rough, and seemed to be running in 2 cylinders. I shut the truck down, restarted it and it ran a little better, as I limped it back to the shop.
Golf IV / Jetta IV :: ASR Light Came On / Running Rough And Smoking With Codes
I was driving along the highway cruising at around 100 km/h when out of nowhere the car started driving a little rough so I look down and the ASR (traction control) light was on. I got off the highway, shut it down and fired it back up. The ASR light was off and car running like normal. When I got home I scanned it and these codes came up:
The catalyst code if from my catless turbo-back exhaust which I plan to fix next month with a tune. Anyway I cleared all codes and continued on my way without any other hiccups. So is my MAF sensor dying/dirty? ECU? N75 valve? Boost leak? I'm making a boost leak tester today just to 100% eliminate that variable, though I'm fairly certain I'm good there.
The car is mostly stock except for a few bolt-ons, all of which I've had installed for thousands of kilometers now. Here is what isn't stock, not including suspension, wheels, etc:
Forge 008 diverter valve
034 Motorsports PVC silicone hose kit
Samco boost hose kit
Forge silicone turbo inlet pipe
Eurojet SMIC
custom built 2.5 stainless, catless turbo back
AEM Dryflo short ram intake
GLI MFA cluster
Ford Ranger / B-Series :: Idles Like Crap Up And Down With A/C On Or Off And Eventually Die
96 Ranger 2.3 5 speed, 2wd. 212k on the clock.
Bought this from my BIL last week. CEL was on so I ran the codes. replaced the air filter, cleaned the MAF (with CRC MAS cleaner), replaced the EGR solenoid (physically broken). The first code showed this was throwing the code. That code (p1409) went away but p0402 showed it's head. replaced the DPFE sensor, disconnected the battery for an hour and am now code free.
Now it idles like crap, up and down with A/C on or off to nearly dying and does eventually die. Disconnected the MAS and no change. Cleaned the AIC no change, replaced the AIC with no luck. Checked for any obvious vacuum leaks around items I messed with. Found nothing. With engine running I disconnected the vacuum to the EGR valve and idle smooths out. Feel a small vacuum tug from the hose, nothing at the valve.
Haven't changed the PCV or cleaned the throttle body. Could it be the EGR valve since removing the vacuum seemed to work?
Side note, BIL's mechanic told him THREE YEARS AGO the CEL was 'probably a O2 sensor' and that is doesn't do anything and no need to fix.
Still no codes and still no power. Can't hear any vacuum leaks. Bought new plugs and wires but haven't installed them yet. EGR? TPS?
Ford Fuel System :: Idles Very Rough - Gas Smell
The carb on my 460 in my truck is acting funny. It almost sounds like a dragster It Idles really rough. I tried setting the Idle mixture screws on the side of the metering block. I bottomed them out and them turned them out 1 1/4 turns. I started turning them in till I got the highest reading on my vacuum gauge, about 13 hg. The screws are only about 1/4 turn from being bottomed out. It was running smoother, then it stalled when I restarted it, it started running really rough again.
The exhaust smells of gas. I turned the screws all the way in just to see what would happen, I thought it should stall but it didn't. I had my timing light hooked up and checked it now and then during all of this and it didn't change at all. The screws had almost no resistance to turning, shouldn't they have some resistance?
Ford :: 1996 Ranger Idles Roughly, Stalls Out During Hot Weather
I recently purchased a 1996 Ford Ranger with the 4 cyl. engine. The first 10 days I owned it it ran just fine. I then took a an hour drive to another city. After the first few stops there, as the temperature outside reached about 90, It started to sputter and idle very badly. After I got rolling it would would run fine. I decided to try to make it home. It ran fine at freeway speeds of about 70 mph. I had to stop once; it stalled out and would not start again. After waiting about ten minutes I tried again. It was still running rough, but I was able to get rolling and drove the rest of the way home without any problems until I was in town and had difficulty keeping it running at idle.
The next morning it ran fine again. A local mechanic changed the fuel filter, but the problem came back as soon as the temp neared 90 degrees. A mechanic friend who witnessed the problem said that it definitely sounded like a lack of fuel and not an electrical problem. Is there a way to troubleshoot without swapping parts? If the fuel pump is failing in warm weather, how is it possible that it runs fine at 70 mph, but not at idle? Engine temp gauge looks good. I did get one code after it died the first time (lean mixture, I think he said).
Ford Ranger / B-Series :: 1997 - Idles High And Accelerates On Its Own Sometimes
My ranger has a 3.0 v6 engine it idles high and accelerates on its own sometimes. Sometimes its more often then others. I turn my key about three times thinkin its reseting the computer and stop it and it does. But I keep hitting a dead end and don't know what to do about it.
View 10 RepliesFord Ranger / B-Series :: 1996 2.3L 5 Speed Idles Too High
My son just purchased a 1996 Ford Ranger 2.3l 5 speed it is a nice little truck. But I have a question when you press in the clutch it acts like the choke has come on it idles way to high. When you come to a complete stop it is a few minutes before it goes back to its regular idle. Is it suppose to do that?
View 9 RepliesFord Ranger / B-Series :: 2003 4.0L Idles Fine But Stalls When Given Gas
I'm having a bit of trouble with my fathers '03 Ranger Edge 4.0L. It has about 100k miles on it, and we keep it very well maintained. This is the first major problem we've had with it.
When the problem first occured, it had been driven about 30 miles on the highway and about 5 miles after getting off the highway, he pulled up to an intersection and stopped. As he started accelerating again, it all of a sudden started sputtering, surging (almost exactly as if it were running out of gas), and then stalled. It continues to exhibit this behavior. It will start and idle fine, but struggle and then stall when given any amount of throttle. It's also an automatic transmission if that makes any difference.
Fast forward to this past week after we had it towed home. We have checked the fuel pressure, and its dead on at about 64psi. We changed the fuel filter, changed the PCV valve, changed the upstream O2 sensor, put in a new air filter, cleaned the MAF sensor, and cleaned the intake of the throttle body. We're now at a loss as to what could be causing the problem. The CEL is not on, and there are no codes being shown when we plugged it in. We also thought it may have been bad gas, so we drained the tank and put fresh gas in from our preferred station. The plugs and wires are also fairly new, only about 4k miles on them.
Are we missing anything here? What else we could try? The absolute last resort is taking it to a shop, we're going through a rough patch with finances.
Ford - Focus :: 2011 - Idles Rough When Come To A Stop, In Drive
When I first start out driving the car, and come to a stop, in drive, the car begins to run rough. I can hear and feel the vibration, it's very noticeable. I put it in neutral and it stops. As I load the engine with AC or use the electric windows it seems to gets worse. Then after driving for about 5-7 miles, it quits. Primarily in cold weather, since it started 4 months ago. I do allow the car to warm up before driving.I'm still under warranty, and have been to the dealer 3 times. Of course, it doesn't happen when I go to see the dealer. But they did re-tighten the motor mounts. I don't think it worked.
View 12 RepliesFord 6.0L Power Stroke Diesel :: Sputters And Idles Rough When AC Off?
So I am relatively new to diesel engines! I have a f250 6.0L, that every now and again sputters and idles rough, when the ac is off? Yes I did say off. It's only done this twice, but when I turn the ac on it goes away and runs fantastic. Not sure what could cause this, and think it's a little weird that it's not consistent. Sometimes I run it without ac and it's fine, but this has happened twice now, so I thought it might be worth figuring out.
View 2 RepliesFord F-150 - 1997-2003 :: Idles Rough And Seems To Lack Power
I am working on a 97 4.6 with 146k for a friend. It idles rough and seems to lack power (then again a 4.6 lacks power )
Has New:
plugs
wires
coil packs
fuel filter
sea foam intake
sea foam fuel
I have checked:
proper egr function
vacuum leaks
cleaned IAC
steady 17-18 in vac
clean air filter
cats do not seem to be getting too hot.
no codes
KOEO test ok
KOER test ok
The plugs worked some. Dirty MAF, clogged cats??
Ford - Explorer :: 2007 - Hard Start - Idles A Little Rough
After sitting engine cranks longer than it usually did before it starts. idles a little rough. engine light comes on after it been running about 30 sec for 1 min. after that seems to run fine.check codes po446 and p1633 always come up. if you let sit a bit with key on starts right up.replaced gas cap checked evap lines, and changed filter no luck. Did notice with lines off evap solenoid key off or on i can blow through it. that doesn't sound right.
Checked fuel pressure. key on jumps to 90psi then falls to 55psi and stays. turn off key and leaked off 10psi in 5 min.start engine while watching gauge does the same as when the key on except it falls to 30 to 35 psi and bounces between them. i think this is way low. What is the correct pressure? Shut off engine and drops to 20 in 5 min. Next I plugged line on test tee going to fuel rail and tested same results as key on. the convinced fuel pump was bad since regulator and check is there. replaced pump. problem still there.
Ford Ranger / B-Series :: 1991 - How To Time Idles High At Start
I now have a 1991 ranger 3.0 super cab. I need a step by step walkthrough of how to time it. Keep in mind that I ha the distributor out while turning the engine over so I need from start to finish, including the spout connector. It runs right now but idles high at the start and the. Stumbles down to about 500rpm and sometimes dies....
View 12 RepliesFocus :: Ford Idles Rough Once Engine Starts Coming Up To Temperature
We have a Ford Focus wagon that idles rough once the engine starts coming up to temperature. When you first start the car it's fine. For example, today I started the car, drove it up the road to the store and it was fine, but upon returning to my driveway just a few minutes later, as the engine temperature was just starting to come up, it started idling really rough. The idle is so rough it sounds like it's on the verge of stalling, but it never has actually stalled. An oxygen sensor has been replaced and it was good for a while, but now the problem is back. The check engine light is on as well.
View 2 Replies