Golf IV / Jetta IV :: Running Rough And 3 Codes Stored - Cylinders 2 And 3 Misfire
So my daughter's 2000 Golf Mk4 with 160,000 miles on it was running rough and had 3 codes stored - cylinders 2 & 3 misfire and a 411 secondary air injection problem.
Having had the misfire code before I swapped injectors around and the error code moved cylinders with the injectors so I attempted cleaning them and also cleaned the throttle body and intake manifold. At this point car still running rough but also started smoking badly.
Replaced the following items:
- Spark plugs
- Spark plug wires
- PCV valve
- PCV hose
- Fuel injectors w/ remanufactured
Hose reconnected between secondary air injection pump and air intake - previous owner had duct-taped it in when he couldn't get it to seal I guess. I've never heard it run.
Car running better, idles more smoothly, doesn't stumble or stall like it did before, no error codes coming up BUT car smokes a lot and the fumes make me feel sick just driving it a mile.
The car had never smoked like this before, hasn't had a whole lot of love the last year or two but no real problems either so why the sudden smoke?
At first I assumed it was cleaner being burned off but that should have been gone in under a minute and this is on-going. It's bad enough to not only be embarrassing but apparently dangerous as the fumes are bad.
Golf IV / Jetta IV :: 2.0 Engine Is Sputtering And Rough Running On Morning Start - No VCDS Fault Codes
I have a 2008 MK4 2.0 with only 53,000kms. At 40,000Kms I put new OEM spark plugs.
Just recently, every morning when I start the engine is sputtering and rough running. The engines want to die but I give a little gas, and run rough like it is only firing on two or three cylinders.
When it gets to the normal operating coolant temperature it runs without any problem and I can use the AC. Its only give me this problem on the first start of the day.
Does not have any MIL light on the instrument panel. I scan it with VCDS-Lite and do not found any fault codes. The only thing that's come to my mind is to change the Green Coolant Sensor.
Ford Excursion :: Running Really Bad / Misfiring / Smoking And Sounding Real Rough
So Friday before last my ex laid down on me while i was headed to work. So I parked it in a walmart parking lot and caught a ride to work with a friend then had it towed home that evening. Problem i was having is it started running really bad, miss firing, smoking, and sounding real rough, but I wasn't getting any trouble codes. So after both uvch's, icp, ipr, icp pigtail, checking fuel for water contamination and pulling my hair out, i decided to check the oil and found it to be 4 quarts low. Talk about feel like a knuckle head.... While it was down it did receive a new water pump, a diesel site 203* thermostat, new billet thermostat housing, Gooch's Radiator Flush Procedure, and some fresh rotella etc.
View 5 RepliesTrailBlazer :: Running Rough And SES Light On - Codes P0340 And P0300 Misfire Detected
04 trailblazer, 4.2. Running rough and SES light on. Had codes pulled and showed p0340 (CMP sensor circuit malfunction) and p0300 (Multiple engine misfire detected). Replaced the CMP sensor and left negative battery cable unhooked for 20 minutes or so to clear the codes. Upon start up no more SES light and idle was slightly better. Within seconds it SES was back and it is again running poorly. Cruise control is no longer functional as well.
View 7 RepliesFord F-150 - 1997-2003 :: Running Rough Under Light Acceleration / Codes P0300 And P0301
Just got a 98 f150 w/ 5.4 4x4 excab. It idles fine but under light accleration. It starts bucking and missing bad, if I step on it, it down shifts and accelerates fine. If I try to maintain one speed it misses bad. It is not throwing any codes right now. The check engine light did come on for like a minute but went back off before I could have it read. I hooked up a scanner just to see if any codes were stored and got p0300 and p0301. I am going to clean the MAF and check for vacuum leaks. I hear the rear plug and coils can get water in them causing similar problems.
View 8 RepliesFord Excursion :: Running Rough And Check Engine Light Came On - P0353 And P0358 Codes
The X has been running great, well good enough, lately with no issues. I left work the other morning, and apparently the X didn't want to wake up that early. As soon as I started it up, the check engine light came on and it was running like crap. Had a bad hesitation all the way home. It feels like it is misfiring, but only under load. It doesn't do it if I brake torque it or Rev it up. Only while driving.
The codes I am getting are in the P035x family (typed that way for future searches). P0353 and P0358 are the codes I am getting (along with 4x4 codes for the vacuum solenoid...but that's the solution to other problems not relevant to this!). Being codes for the primary circuit, I popped the hood and checked out the connectors. Both connectors are fine, and tightly connected. I did notice however that cylinders 3 and 8 have other than OEM coil packs on them. These are the only 2 cylinders with those coil packs (they are white and the other 8 cylinders have black coils).
I don't want to just throw parts at it, and I'm not getting a hard miss fire code, just the 2 above. I might try to swap the coils with other cylinders tonight and see if the codes move to those cylinders. It has run like this a few times, but never set a code, and turning it off and back on has "fixed"this in the past.
And just for complete disclosure, while looking for where I saved a password, I found notes from August last year where I pulled codes, and these two codes were present then, with a cylinder 7 hard miss fire code. I replaced the c7 coil with motorcraft cleared the codes, and P0353 and P0358 went away and I haven't seen them since. The plugs are brand new and only have about 1000 miles on them (changed them in September when repairing the misfire and I don't drive it much).
Golf IV / Jetta IV :: 2011 - No Fans Running While Engine Was Going - Multiple Codes Came On
I bought my 2001 Jetty w/2.0 only yesterday. While I was looking under the hood this morning, I noticed there was no fans running while engine was going so I took a trip to local auto parts store. O'Reilly's hooked up my Jetty and told me there was four error codes but they weren't sure what they meant. Here are the codes: P0302, P0301, P1128,and P1580. I have no clue of what these errors mean. I am not familiar with Volkswagen at all and there are no volkswagen dealerships close.
View 3 RepliesGolf IV / Jetta IV :: 2003 GLI 24v VR6 Running Rough And Stalling Out
I have been beatingy head against the wall for the last month with this car. It started out by just running really rough and stalling out. Found out that I had a bad clamp on the air intake that attaches to the throttle body. Replace that after I already replaced the MAF. Everything was great till couple days later then the car just crank crank crank no fire....
I cleaned the grounds pulled the plugs and coils, had perfect spark. Put everything back come to find out after going thru my Bentley manuals I jumped around the fuel pump relay fuel pump kicked on perfect started great! Replaced the fuel pump relay BAM! Ran great!!!! For 2 days..... After that right when I pulled into the drive way the car would not start.... So I tried everything again.... To no avail..... Check the codes again, now I'm throwing these codes which yes I did cross reference in my Bentley manual.
P1117- O2 sensor heater circuit bank 1 sensor 2 short to ground
P1198- O2 sensor heater circuit bank 1 sensor 2 electrical malfunction
P1472- EVAP emission control LDP circuit short to ground
P1516- Intake manifold changeover valve circuit open
And the dreaded same code I've had the whole time........
P0102- Mass or volume air flow circuit low input.
I have also tried tracking down any bad wires, and testing resistance...
Golf IV / Jetta IV :: 1.8 Running Poorly / Rough Idle
the last couple weeks the engine has been running poorly, rough idle .... and sputters until about 4k rpm with a noticeable loss in power. No clue what it is ... it seems to spring up after I got a coolant hose leak on top of the motor.
View 2 RepliesFord Super Duty (1999-2016) :: Running Rough - Check Engine Light Came On And Got Codes P0171 And P0174
My 1999 F350 SD V10 that would crank but not start. I ended up checking numerous things because before it decided to truly stop running, it would run rough for a time and then be fine. The check Engine Light came on and I got the codes P0171 & P0174. Well, I bought MAF Cleaner and took the air cleaner housing off, disassembled it and thoroughly cleaned the sensor and replaced the air cleaner. I continued to get those same error codes, but before I could go any further, the truck totally died. It sat for nearly 2 months with the bed in the air as I had decided to lift the bed to check the fuel pump vs. drop the tank.
Fast forward a bit and I have since replaced the fuel pump and put $40 of Premium Gas along with Royal Purple Fuel Treatment in the tank because I figured things got stirred up and could use a bit of cleaning. I do not drive much, and during the first few trips, it ran perfectly. Then today, it started again with the rough running and trying to die if I let it idle. If I pushed on the gas, it would completely smooth out. If this were a carbureted engine, I would think the low idle was set too low, but since it is not, I am guessing it is one or more of the sensor/s that is/are causing the issue.
I am disabled and can’t play parts swap until I hit on the right part, so I was hoping that I might get some guidance here to narrow things down to the most probably causes so that I won’t go broke changing things until I hit the “right one”. The truck has 153,000 miles on it and I had bought it from a retired couple who used it to pull their 5th wheel travel trailer, so it had mostly highway miles on it. It was immaculate when I bought it and ran perfectly, needing only normal maintenance (oil changes, etc.) over the past 12 years that I have owned it. In those 12 years, I have put about 60,000 miles on it.
Golf IV / Jetta IV :: VR6 Running Rough For A Minute Or Two After Hard Start
I just replaced my injectors in my 12v vr6 and now having some problems. Mainly having issues with start up. Having to feather the gas to get it to start and still runs rough for a min or two.
View 3 RepliesGolf IV / Jetta IV :: 2002 - Running Rough Then Stalled After Starting
So the Jetta started running rough, then stalled after starting. Couldn't drive it home so I had to tow it. Got to the house and read codes. It gave me P0135, P0171, and P0321. I researched and saw that the only code of these three whose symptoms included stalling was P0321, so I replaced the Crankshaft Position sensor. Tried starting it, and it wouldn't start at all. I kept at it for a while thinking it would catch, but after 5 minutes the battery was too low to crank. I tested the old crankshaft sensor, and had resistance of about 900 ohms, so it was in range. For giggles, I pulled the new one and checked it, also in range. I put one of them back in, and proceeded to scratch my head. Charged the battery up, and now not sure what to do. I need to do a very close hose inspection, but there are no obvious tears or breaks.
View 1 RepliesGolf IV / Jetta IV :: VW 1.6 SR (AKL Engine) Rough Running / High Fuel Consumption
Regarding my problem (outline below):
>> Went for a refueling stop, and thereafter proceeded onto the highway
>> Approx. 500m into the drive onto the highway the car started jerking and running rough with an initial puff of smoke (none thereafter)
>> Immediately after this initial jerking/shuddering there was a significant increase in fuel consumption i.e. from a familiar 8.2L/100km to 18L/100km in the cruise
>> We continued driving not knowing what it was (I suspected a spark plug may have stopped working)
>> Pulled up at the gas station to observe what went wrong inside the engine bay - no signs of any leaks, fuel sprays, etc. but only that the engine was shaking
>> I checked the rear of the car while the car was idling and observed a pulsating sound...some light smoke and a fuel-rich egg-like smell
>> Asked around and I was led to think the catalytic converter was ruined, so the next day I had the catalytic converter cut out
>> After removing the catalytic converter the problem persisted...although the engine operated with slightly less flow resistance
Attempt at diagnosing the problem
>> My wife called in a technician from BMW at Canal Walk to come have a look and what errors were flagged
>> The tech ran the diagnostic and no fault codes were indicated, except a few short circuit faults due to my incorrectly placing -ve on +ve when I tried to charge my cars battery with jumper cables
>> He proceeded to ask if we changed the spark plugs, I said yes. He then looked at the oil on the intake manifold and said there could be a torn valve on the intake manifold and that air that is not measured by the air mass flow sensor is entering the engine, which is causing the car to rev hunt (this problem of rev hunting has been with us for a while). The engine also shuts down uncommanded at stops and sometimes between shifting gears with the subsequent loss of power steering (very dangerous!!)
>> We also had the O2 sensor replaced a month before this occurence
The images attached (#1- #3) are marked up to indicate the component I am referring to.
[IMG] FilesImage_1.jpg[/IMG]
[IMG] FilesImage_2.jpg[/IMG]
[IMG] FilesImage_3.jpg[/IMG]
Went to Cape City VW in Cape Town and the part number for that orange thing/diaphragm is 06A 198 205A 'Repair kit for valve'. Is this significant? The car sounds as strange at idle...as if has noisy valves. I can upload (if there is an option) a sound clip of how the car sounds if this assists.
Golf IV / Jetta IV :: 1999 - When Pulled Out Of Driveway Car Started Running Rough
I have a Jetta Mk IV, yesterday I went to go drive it and just as I pulled out of the driveway it started running rough, so I pulled back in the driveway and the coolant temperature sensor light came on, then the check engine light. and then it died. Then today I tried starting it, and it will only start and run if I have the gas pedal all the way to the floor, and it runs really rough. Then it will die. I thought maybe the coolant temp sensor since the light came on. I replaced that, and it still does it. I'm leaning towards a head gasket.
View 2 RepliesGolf IV / Jetta IV :: Running Rough / Flat Spot When Accelerating Around 2000 And 2600 RPM
My 2.0 recently had some problems with the coil pack so I replaced it. Now my car hits a "flat spot" when accelerating around 2000 RPM and then another around 2600 RPM. If I am in 3rd gear going about 20MPH and I press the gas about 25-30% it sort of shakes and won't accelerate and when I take my foot off the gas and slowly ease the pedal down it accelerates fine.
My car also runs pretty rough at a cold idle(misfires). When I press the gas it sounds smooth until it gets back to idle. At any temp my car runs really rough with the A/C on. I also hear a rattle/Buzz around my relay panel when the A/C is on. My car is a 1999 2.0 AEG. I don't have VAG-COM just a generic scanner and the last codes I got were:
P0134
P0135
P0141
I replaced both O2 sensors and the beginning of this year and those codes came back right after I did them. I will scan tomorrow and post any new codes.
Golf IV / Jetta IV :: Chokes The Power Past 3500 RPMs And Continue Running Rough
I own a 2001 Jetta GLX 12v VR6, lately the car has not been running well. It chokes the power past 3500 rpm's and will continue running poorly and sound sort of like a Subaru boxer engine. Sometimes it corrects itself and runs okay but goes back and forth.
I ran the codes on VAG COM:
6 faults found:
17551 - Load calculation cross check
P1143 - 35 - 10 upper limit exceeded - intermittent
16712 - Knock Sensor 1 (g61)
P0328 - 35 - 10 Signal too high - intermittent
[Code] .....
I ran VAG COM a couple of days before these codes came up and I had a different code dealing with air/fuel mixture, something about fuel running to rich. I'm stumped.
Golf IV / Jetta IV :: Light Comes On Throwing The Codes
I recently had an issue with a coolant leak. the Y shaped coolant line connection went bad located under the power steering reservoir. The car got hot and the coolant light came on i immediately turned the car off and saw coolant leaking out from this.
Now today I start my car it has a rough idle and dies once it dies it doesn't start again and the epic light comes on throwing the codes
17579 P1171 Throttle Actuation Potentiometer Sign.2 Range/Performance
17951 P1543 Throttle Actuation Potentiometer Signal too Low
16497 P0113 Intake Air Temp.Circ High Input
17987 P1579 Idle Speed Contr.Throttle Pos. Adaptation not started
17953 P1545 Throttle Pos.Contr Malfunction
17976 P1568 Idle Speed Contr.Throttle Pos. mechanical Malfunction
18012 P1604 Internal Control Module Driver Error
Golf IV / Jetta IV :: EPC Light Came On - Codes P0221 And P2637
I bought my son a 2005 GTI MkIV (great dad right). On the drive home it threw a light the code was P4011 secondary air no prob found a hose off and issue solved. The car had 66k so I made him leave it at home until the timing belt was changed (read about alot of failures between 60 and 80k). Everything was great for 2 weeks last Thursday the EPC light came on and he got it home in limp mode. I pulled the following codes P0221 and P2637.
Am I looking for a short? I have read that it has been the following.
Brake light switch
Gas pedal
MAF
Intake manifold...
Golf IV / Jetta IV :: VR6 Won't Start And Smoking From Coil Packs
I've had my 24V off the road for about a year now working on it. I did some wire tucking and what not, nothing major. Now when I go to start it, it won't start and it will make a popping noise from a coil pack and it starts to smoke.
View 6 Replies