Ford Ranger / B-Series :: 1994 - Thumping Sound During Braking / Bad RABS?
'94 Ranger 4x2. Recent new brakes front and rear, installed by a garage who was also doing my clutch a few months ago. Not long after brake job, slightly detectable 'thump thump thumping' sound during braking. At first I thought possible stuck caliper/warped front rotor, but vibration was not in the steering wheel, and as sound grew increasingly louder, seems to be coming from right rear brakes.
ABS light appeared once, but after adding a small amount of brake fluid to master cylinder, has not reappeared. No other brake related idiot lights, and truck brakes quickly and straight. Pedal could possibly be firmer, however.
Took my rig back to the shop, since brakes were supposedly "guaranteed for six months". Out of business, no forwarding address or phone number!
So I decided to bleed the rear brakes. Haynes manual says bleed RABS valve first, then proceed to rear brake bleeders. Found RABS on rail frame, dust cap still on bleeder, (cap was very dusty and difficult to pop off) looks like shop never removed it or bled it! Had to remove its electrical connector to access the 7/8" bleeder nut with a box wrench.When I tried to bleed it, NOTHING came out. Neither air nor brake fluid. Moved on to rear brake bleeders. Normal. Bled 1/2 pint from each, as I topped off the master cylinder. I have not yet removed either drum to inspect.
Long story short, does the RABS valve on a '94 Ranger rear wheel only ABS need to be plugged in to be able to be bled? Do I need to have the ignition 'ON' while doing so? (I thought only '95 and up needed the Ford factory code reader to bleed four wheel only ABS valve?) And can the thing fail without setting the ABS warning light, and allow the rear brakes to still (noisily) work ?
Ford - Ranger :: 1994 - Coolant Leak Originate From The Driver Side
I seem to have a coolant leak somewhere - i changed the oil yesterday and while i was at it i topped off the coolant in the recovery tank to the cold line. Took the truck out for about a half hour then parked it over night. when i came out this morning i found a pretty sizable puddle on the ground, seeming to originate from the drivers side, and when i checked the radiator it was low but the coolant recovery tank was full past the cold line...i let idle today for about a half hour then let it cool down trying to catch it in the act but saw nothing. if i trace the source of the puddle it seems to be coming from the cap area or at least that side of the compartment. would this be the radiator cap itself? allowing coolant to boil over and out but not get sucked back in? Since I've had the truck i have noticed a small, very small, amount of coolant on the ground now and again but this is the first big puddle.
View 1 RepliesFord Ranger / B-Series :: 1994 - Coolant Loss / Head Gasket Leaking
I am working on my buddy's 1994 Ranger with a 2.3L I4 that has been going thru a large amount of engine coolant. The trucks has approximately 180,000 miles on it. When I had it parked on concrete I have not seen any signs of coolant on the concrete or any signs of coolant leaking. The next place I checked was inside the cab to see if there was any coolant from the heater core and there was not. The water pump has been replaced a couple of years back. I replaced the spark plugs today and did not see anything on the plugs that I would have thought were signs of coolant in the combustion chambers.
With that being said I have not worked on a vehicle with a leaking head gasket before. Would there be any visible signs on the sparks plugs? If so what would I be looking for? When standing in front of the vehicle with the engine running there is a slight smell of antifreeze being "vaporized". Are there any noted issues with this engine that would cause this? Are there any other things I should check? Could it be a leaking head gasket causing this? If so how can I check for that?
Ford Ranger / B-Series :: 1994 2.3L - Coolant Leak Coming From Under Black Plastic Cover
I noticed green coolant leaking from bottom of black, what I think is called, timing belt cover. There is 188, 000 miles, and when I changed the timing belt, I did not change the water pump, although I did change out the thermostat. I have done a lot of work on this truck in the past. I checked the oil and no signs of water or coolant mixed in. The water pump is not weeping from the top well. I rely on this truck and the way I look at it is I may just keep driving it until it goes kaput (its real beat up). Should I go to an auto parts store and see if I can buy some sealant. I would guess it is either the water pump or maybe the timing cover gasket? I have inspected all hoses, and I see nothing. The leak must be coming from somewhere under that black, plastic cover. I am capable and willing to do just about anything other than perhaps a full engine pull, although I have the wherewithal to do that too if absolutely necessary.
View 9 RepliesFord Ranger / B-Series :: 1994 XLT 2.3L - EVAP System Would Not Hold Pressure - Diagram?
I have a '94 Ranger XLT with the 4 cylinder 2.3L motor. I recently failed my smog test here in CA because the evap system would not hold pressure. All the emissions were perfect, but it wouldn't hold pressure. I changed the fuel filler neck -- it was cracked -- but there is still a problem somewhere. Is there a diagram that shows where all the hoses are for the evap system? I'm thinking that some other hoses might be cracked since they have been there over 20 years. Is this a good place to start looking or should I be checking something else?
View 4 RepliesC/K :: 1994 - Rattle Loudly At Idles Comes And Goes
i got a 94 chevy k2500 6.5 vin f with nv4500 and a dual mass clutch. been fixing things left and right and have been putting this off but has been getting worse over the last 4k miles(only had for those miles)has 242k miles on it. i have a rattle coming from what sounds like the rear of oil pan to the bell housing. its quite loud only at idle comes and goes as it wants to. drives fine idles fine. i rotated crank to see if the crank was broke and i have no slop in it.
Guy said he had new clutch put in 5k miles ago i have to overhaul the trans per grinding 2nd and 3rd gears when downshifting. I do not tear trans out and need extra parts i didn't plan for cause i only have one hoist and the shop. i checked the crank pulley its older but not moving an excessive amount i have motor mount on my tool box i will be putting in in the next few days. have new injectors in it as well and is not an injector knock. Engine will shake when it rattles to.
Ford - Ranger :: Running Loudly - Oil Pressure Gauge In Red Then Normal
Twice in the last year my 1999 Ranger (@138,000 miles) has started running very loudly: I checked dash and see oil pressure gauge says no oil pressure. First time this happened, I pulled over, had it towed. At garage they start it up: gauge normal, they check oil says its OK. I take it to the dealership, they replace sending unit, but can't explain why it was running loudly. Today same thing happens: I checked oil pressure gauge, it's OK. After an hour, starts running loudly, gauge in red. Park car for 15 - 20 minutes, start it up: all is well: gauge OK, running quietly. This is amy 'spare' car, so it only gets driven 1 -2 times per month, short distances.
View 4 RepliesFord Ranger / B-Series :: 1993 / 3.0L V6 - Belt Squeaking Very Loudly
I have a ranger as said in title. No a/c. I noticed my belt was cracked very badly so I bought a new one. Dayco made for Ford and Mazda 3.0L V6. Looked the same length as the old one so I put it on and all was good. Then about 2 days later it started squeaking very loudly, not all the time, just 1500 rpm and higher. The hotter the motor got (not overheating just to running temp) the higher rpm it took for it to squeak. I put a stethoscope on all the pulleys/pumps and alt. It sounded the strongest on the idler.
So I replaced the idler and bearing (which the bearing was bad, but not the source of sound) it wasn't that. So I thought I'd give the belt a couple days, maybe it was too tight causing a bearing to get too tight and squeak. And the more I drove it the louder it got with less rpm needed to make it squeak. So I tried belt dressing, and still no fix. So today I put the old belt back on to see if that was the issue. Sure enough, it started up and squeaked just the same, but I tried the belt dressing on the old belt and it went silent, even at 3000 rpm. So I assume from this the new belt was a smidge too big. Right?
Ford Exhaust System :: 1994 Ranger - Loud Exhaust Sound In / Outside The Truck And At Idle
I have a 94 ranger 4L. I am looking for a more loud exhaust sound in/outside the truck and at idle. I have had a cherry bomb turbo on it and it was ok but not loud enough for my liking. I just picked up a flowmaster 40 2 days ago and it sounds good but again just not loud enough for my taste and kinda a lot more. I was looking for a louder muffler that is not a glasspack and would like to stay under like 80 or so.
I also thought about getting a high flow cat which i think might make some more sound but was not sure. Im running the stock pipe which is 2" and end in back of the wheel on the right. I look at the Hooker Headers Maximum Flow Muffler which i thought would be louder b/c it's more straight through the muffler so it would put off more sound better. What would u recommend for something more loud ?
Jeep - Grandcherokee :: 1994 - Thumping Sound Coming From Drivetrain
When I drive over 55 i have a shaking through the car after driving for a while if you put it in reverse it feels like it is binding up and when you put it in park you can hear a thumping sound coming from the drive train i have replaced both cv shafts in the front (they were bad) and the passenger side hub. I am going to replace the ball joints with after market ones because it pulls to the right and the stock ones do not have a camfer adjustment is the binding a differential problem or a transfer case problem also if while the engine is off if you shift to neutral you can feel it release the tension on the drive train.
View 2 RepliesFord Ranger / B-Series :: Thumping Noise From Under The Hood
Driving home from work (a 30 minute hwy cruise) I had to stop for a traffic light. As was sitting there I hear a thumping noise from under the hood, otherwise it was running the same as always. Got it home and I didn't hear it anymore, looked under the hood while idling, seen nothing, shut it off. top rad hose had a slight amount of pressure, started it and it quickly built pressure and felt a rhythmic thumping in hose and it got fricking hot quickly. I figure either a head gasket or cracked head.
I just recently did an aggressive cooling system flush using Prestone heavy duty cooling system flush (can only get this at a dealer) because the previous own neglected it, and it blew a head gasket, tons of rust inside when I did it. I'm gonna borrow a tester to check for exhaust gas in the cooling system and what did it end up being? The guy I bought it from (the previous owners mechanic) put 1 or 2 head gaskets on it.
Ford Ranger / B-Series :: 1998 - Loud Thumping Noise From Dash
Ok I have a 1998 Ford Ranger XLT 4.0L automatic 4X4 with A/C my problem is i just had the timing chain,water pump, thermostat, upper and lower hoses, and front crank seal replaced. I got it back and right away noticed a thumping noise at idle only... My gauge was always steady at the same spot it had always been. but the thumping was loud when idling. Now the sound seems to have moved farther towards the engine instead of the dash and tonight when i popped the hood noticed the top hose was collapsed and i could feel no pressure. the thumping noise seems to be coming from the area of the thermostat. I have no oil in the coolant and no coolant in my oil! I tried to get the air bubble or pocket out if thats what is the problem by running the engine till hot with the radiator cap off but it made just a huge mess. it did seem to push a huge air pocket out but still does the loud thumping. This all started the day i got it back from the mechanic so I am assuming its an air pocket. I planned on changing the thermostat tomorrow.
View 14 RepliesLexus LS 2007+ :: Sound System Stopped - Loud Thumping Noise Comes Up
The sound system in my 2008 LS 460 suddenly stopped and a loud thumping noise comes up in all speakers even if the radio is turned off. There is no music at all only that loud noise. Bluetooth does not work as well as command voice and the GPS guiding system. I had to remove the fuse to stop the thumping sound. To answer my telephone I must pull on the side of the road and turn off the motor. Car dealership said that it is the first time they see that. The car is scheduled to be looked at in a couple of days.
View 8 RepliesFord - Ranger :: 1994 - Very Low Power
Pickup developed low power issue (won't go over 35 unless downhill) suddenly, I'm told. Already had other issues. Replaced the engine with a used one, replaced the MAF sensor, and replace the ECM. Took care of all issues except low power. In neutral RPMs top at 3000. New fuel and air filters, distributor cap & rotor, plug wires. Runs smooth, idles fine, just no power.
View 5 RepliesFord Aerostar :: 1994 - Coolant Leak Behind The Water Pump
1994 - 3.0 .... Back behind the water pump there is a stream of coolant what could that be. Water pump has been replaced earlier last year I thought that fixed it,there has always been a mystery leak..
View 6 RepliesFord Fuel System :: 1994 - 4 Injectors Do Not Pulse
I have a f53 motorhome and 4 out of the 8 injectors pulse. The front 2 and the back 2 don't pulse. The middle 2 on both sides work perfect. Why would they not pulse and only give out positive on the two wires to the injector on the one that don't work. The ones that work they pulse.
View 8 RepliesFord - Ranger :: 1994 - Speedometer Not Working
My speedometer does not work. Also, my 4wd high light is on but not engaged. Are the two related? I've looked up speed sensor and it's separate from the actuator for 4wd. Maybe coincidence they stopped working simultaneously? Should I start with the speed sensor?
View 1 RepliesFord Ranger / B-Series :: 1994 - Jerking Below 3k RPM?
My 94 ranger, 3.0 v6 began to sputter and jerk about a month ago. It does this when ever give more then lite throttle up until about 3000 rpm. I have replaced plugs, wires, coil and cleaned the air flow sensor. I feel like this has worked a little but the problem is still definitely present. When I hit 3k rpm if feels lie the truck begins to run correctly and almost like it had a power ban much like a dirtbike, but again it's just the truck running correct.. And above 3k rpm it runs great... and every so often the problem will completely disappear for 5 minutes or so, then come right back.
View 1 RepliesFord Ranger / B-Series :: 1994 - Mpg Dropped - Fix?
I have a 94 2wd 4.0 auto 3.08 rear end it has 195,000 im gettin 15 city 18 hwy I used to pull 24+ hwy I changed plugs and wires no change? It has the 4.0 tick but its always had it....
View 7 Replies