Ford 7.3L Power Stroke (1999-2003) :: Truck Runs Very Rough And Lacks Power When Cold
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Rough And Lacks Power When Cold But Smooth At Warm?
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 RepliesFord Super Duty (1999-2016) :: 2005 - Idles Rough - Lacks Power?
I have a 2005 f250 with a 5.4 3v. I bought the truck with a cracked passenger side exhaust manifold about a year ago. We'll here recently the crack got worse and was giving the code P0171, so I had a shop replace it. I picked the truck up and not even a mile down the road it started idling terrible at lights and had very poor acceleration. And it gave me P0174 this time. It's only gotten worse now it's reading P0172, P0174,P0161, and P1489. I've replaced the spark plugs, MAF sensor, both vct solenoid, an the upstream o2 sensor on the passenger side. I also know I don't have any intake or vacuum leaks, I've had a shop check and so have I. It's starting to get expensive just replacing stuff. So, maybe I have a clogged catalytic converter ?
View 8 RepliesSilverado :: 88 Chevy K1500 - Truck Lacks Power / It Idles Rough
I have an 88 chevy K-1500 4x4 5.7L ... My truck lacks serious power, it idles rough, sometimes wont idle at all, sometimes Truck Idles fine. I have adjusted the timing to tdc, and 4 deg. both ways still runs like crap.. Sometimes I can keep it idleing, put it in rev. or drive, and it will die. I have no power and if I put my foot in it too much it will backfire. but will only backfires when in gear and press on the gas to put a load on the motor. I have replaced the: tps, map, egr, pcv, distributor, cap, ignition coil, rotor, plugs, wires, timing chain, both sprockets cam and crank, checked all hoses for leaks, replaced the injectors, the O2 sensor and have changed the intake gaskets. And am still having no luck...... I am bout to just drop an M80 in the gas tank and watch her burn..
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Runs Rough Then Stalls - Check Engine Light Came On
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
Pontiac - Bonneville :: 1990 LE 3.8 Liter V6 Runs Rough After Engine Warms Up / Looses Power If Give More Gas
Car has 252k miles runs ruff after engine warms up, looses power, if I give more gas, car will sputter, but rev up to 5k engine smoothes out. This situation constantly comes and goes.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: After Start Up Engine Throws Wait To Start Light / Runs Real Rough And Just Shuts Off
My 99 250, 7.3 is having some strange issues as of lately. When I start it in the morning, when the engine has fully cooled down, it starts right up, then it throws the "wait to start light" runs real rough and just shuts off. Run the glow plugs a few times, start it up and it will do the same thing for maximum 30 minutes, then all the sudden I start it and it runs fine. I've replaced the fuel pump, cleaned the fuel bowl, new fuel filter, I just don't know where my problem could be. It doesn't make sense. But once I get it running and it warms up, runs fine all day. Go to bed, wake up, has problems again.
View 14 RepliesFord Ranger / B-Series :: 2008 - Runs Rough With No Power
I just changed the plugs and wires on my 2008 Ranger 3L. Now it runs rough with no power. It was fine before I did the work but I thought I should change the plugs at 215000KM. I used Ford wires but unfortunately I used Bosh platinum plugs and now think I will change to Ford plugs. Do you think the Bosch plugs would be that bad for the Ranger? What is the belt tensioner torx size? I had to move the A/C compressor over to get the #4 plug but had a very hard time trying to loosen the belt.
View 7 RepliesFord F-150 (2004-2008) :: 5.4 Engine Has Top End Noise On Right Side And Runs Very Rough
2008 f150 5.4 30,000 miles the engine has top end noise on the right side and runs very rough no codes cam problem ?
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Misses And Runs Rough?
'03 6.0 Powerstroke. Rough idle AFTER it warms up. Runs fine cold. It seems to studder and miss at mid range acceleration. Egr deleted and new oil cooler installed. New lift pump. Replaced ICP sensor. Have 48.5 volts at the FICM. Replaced the fuel pressure spring to the blue one. All new filters. Does not smoke. Does not throw codes. I need to fix this truck one last time. It has a date with the bottem of a very deep lake! It has been nothing but a pos since it hit the ripe old age of 25k miles!
View 14 RepliesFord Ranger / B-Series :: Runs Rough For About A Minute After Engine Started When Cold
This has been an ongoing issue for about a month. When I start the engine after it has been sitting and is cold it runs ruff for about a minute then smooths out and runs fine. I pulled a P0304 code (cyl.4 missfire) but I do not get a CEL.
I checked the plugs and they were ok but I changed them and the wires anyway as it just turned 50k and the plugs were original. I could live with a little cold ruff idle but the code throwing bothers me. The truck is a 2000 xlt 4x with auto trans. and 4.0 engine. This is my second 4.0 ranger but I have only had it for about 6 months.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Runs Rough When Cold
I have my 2002 Ford F250 Powerstroke. 175,000 original miles by me and only me. SCT, MBRP, Howes or Stanandyne almost always. Runs like new. It starts rough if I don't plug it in. Even on 50 degree days. Then it levels off and runs perfectly. If I plug the truck in I can drive off immediately with perfect operation of motor. I just went 1500 miles. Pulling a car hauler with car. NP at all.
New Glow Plugs, GPR "Yes it works", IPR, New Harness, Buzz Test shows it's fine, New #8 injector last year, New O rings HPOP. My buddy who is a PStroke guy said this trucks runs too perfect for it to be injectors. He recommends seals for the injectors. What does this mean. Or what else can it be. Where should I start.
Ford 6.0L Power Stroke Diesel :: 2003 - Hard To Start And Runs Rough When Cold
My '03 6.0 is hard to start and runs rough when cold. Not just cold outside temps, but engine not up to temp. Starts and runs like a champ once it's up to temp. It was doing this when I got it, but it's getting worse.
From what I've read the common culprits are:
1 - failed solder joints on FICM power supply board
2 - bad power supply side of the FICM
3 - updated flash needed for FICM
4 - injector stiction
5 - leaky O-rings at high pressure oil rail to injectors
I have read up on how to run the voltage test on the FICM with a multimeter.
Seems like I would have to go to a dealer to have the software version for the FICM checked.
I am 100% competent to do the tests and/or repairs myself, but since I recently moved in with my fiance in a condo and my tools are in storage, I will have to do it at a friend's house. That being the case, I want to know what all of the common things are that I may need to check for so I am prepared. So, I wanted to see if there were any other common causes of this issue.
I plan to test the FICM voltage and give FICMRepair.com some business if that's the problem. And if that's not the problem (or maybe even if it is) I will get the injector seal kits and replace all of the injector seals as well as disassembling and cleaning the spool valves in the solenoids. I will also change oil and fuel filters with Motorcraft parts and Rotella synthetic oil while I'm in there.
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Truck Runs Rough When Cold
I have a 2001 7.3 with 259,000 miles. It does not get too cold here, however over the past few winters when the temp is below 50 at night the first minute or two of running out of the neighborhood is tough going unless I let it heat up. It has been getting worse over the past few years and now if its even 55 or 60 I need to let it heat up. Glow plugs? Injectors?
View 3 RepliesFord Super Duty (1999-2016) :: V10 Is Stumbling / Missing And Lacks Power
A couple days ago my truck started stumbling and missing . And is lacking power . It starts fine and seems to run ok above 3000 rpm . But at idle and off it is stumbling pretty bad . And at highway speeds it stumbles once it goes into overdrive . I changed the plugs which where white ( I think lean ) then I bought a new coil pack and moved it through all ten positions ( I just replaced them all about a year ago .) then replaced the tps and the iac today also cleaned the maf and recharged my filter . Still no different . It hasn't been an on going thing . I was driving then stopped for a bit then about 1 hour later went to leave and this is where I'm at .
View 9 RepliesFord 6.0L Power Stroke Diesel :: Hard To Start When Cold / Smokes And Runs Rough Until Warms Up
I have an 03 F350 with the 6.0L. It has 210,000 miles on it and the injectors are beginning to be suspect. Its very hard to start when its cold, smokes and runs like crap untill it warms up.
I've found a set of injectors out of a 2005 truck with 8000 miles on them. The truck was overboosted and blew a head gasket.
Now finally to my question.....Can the overboost damage the injector? Would it be safe to buy these and install them or rebuild them before install or just leave them alone?
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Runs Rough And Stalls After Half Mile?
Here's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
Ford Super Duty (1999-2016) :: F250 V10 Missing And Lacks Power To Accelerate Further
I have a 1999 ford f250 with a 6.8 liter v 10 engine. At about 40mph the truck will start missing and lacks power to accelerate further. This problem is intermittent. Some days it runs great and others the miss appears. Well I scanned and the code reader said that I had a misfire on cylinder 7. I took a chance and replaced the COP and the boot for that cylinder . Ran great for a day and then the miss came back. Same code again. What else might cause this? Are plugs difficult to change in these engines?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F350 Idles Fine But Runs Rough After Warms Up A Little
2000 F350. Starts great. Idles fine. After it warms up a little, it will run rough and lose power like it is only hitting on a few cylinders. It will eventually stall unless I push the clutch in and bring it back to idle and then it smooths back out. I figured it was starving for fuel but I can rev it with the clutch in with no issue. I ran it up to 2500 rpm and held it there with the clutch in and ran perfect.
I let the clutch out and start rolling....missing again. The check engine light does come on but my scanner says that there are no codes stored. If I idle it, it will smooth out, and the light goes off. All I have done so far was change the fuel filter which was almost plugged shut and the housing was full of rust looking debris which I cleaned out. BINGO! Nope. Same issue.
I am really at a loss as to where to start. I bought this with 120k on it and it now has 170k and I have not had to do anything other than routine maintenance.