Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Starts And Runs With Rough Idle For About 10 Seconds When Cold
I have an issue with my 7.3.... the truck will not start if it sits overnight without being plugged in, even in 65 degree weather. It starts and runs with a rough idle for about 10 seconds after its been plugged in for an hour, after the rough idle is gone it runs great .. it will Stat back up as long as the truck is warm (70+).... I've replaced the batteries, glow plugs, starter (it was going bad) and fuel filter. .. also replaced the gpr today. ....
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 - Truck Runs Rough When Cold
I have a 2001 7.3 with 259,000 miles. It does not get too cold here, however over the past few winters when the temp is below 50 at night the first minute or two of running out of the neighborhood is tough going unless I let it heat up. It has been getting worse over the past few years and now if its even 55 or 60 I need to let it heat up. Glow plugs? Injectors?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Runs Very Rough And Lacks Power When Cold
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - Runs Rough And Stalls After Half Mile?
Here's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Idling / Running Rough And No Power
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.
Ford 6.0L Power Stroke Diesel :: 2003 - Hard To Start And Runs Rough When Cold
My '03 6.0 is hard to start and runs rough when cold. Not just cold outside temps, but engine not up to temp. Starts and runs like a champ once it's up to temp. It was doing this when I got it, but it's getting worse.
From what I've read the common culprits are:
1 - failed solder joints on FICM power supply board
2 - bad power supply side of the FICM
3 - updated flash needed for FICM
4 - injector stiction
5 - leaky O-rings at high pressure oil rail to injectors
I have read up on how to run the voltage test on the FICM with a multimeter.
Seems like I would have to go to a dealer to have the software version for the FICM checked.
I am 100% competent to do the tests and/or repairs myself, but since I recently moved in with my fiance in a condo and my tools are in storage, I will have to do it at a friend's house. That being the case, I want to know what all of the common things are that I may need to check for so I am prepared. So, I wanted to see if there were any other common causes of this issue.
I plan to test the FICM voltage and give FICMRepair.com some business if that's the problem. And if that's not the problem (or maybe even if it is) I will get the injector seal kits and replace all of the injector seals as well as disassembling and cleaning the spool valves in the solenoids. I will also change oil and fuel filters with Motorcraft parts and Rotella synthetic oil while I'm in there.
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Runs Hot Under Load
Been fighting a coolant issue on '02 F250 4x4 with 7.3. Truck runs hot when under load (ie towing, or ac running on a hot day going down the road). Will sit and idle all day with ac on high and 100 outside. I hear my fan at cold start as normal but that's the only time I hear it. Still has original water pump, fan clutch and radiator. I know all three could stand to be replaced with 340,000 on it. But can't afford to do it all at once.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Runs Rough Then Stalls - Check Engine Light Came On
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 Idles Fine But Runs Rough After Warms Up A Little
2000 F350. Starts great. Idles fine. After it warms up a little, it will run rough and lose power like it is only hitting on a few cylinders. It will eventually stall unless I push the clutch in and bring it back to idle and then it smooths back out. I figured it was starving for fuel but I can rev it with the clutch in with no issue. I ran it up to 2500 rpm and held it there with the clutch in and ran perfect.
I let the clutch out and start rolling....missing again. The check engine light does come on but my scanner says that there are no codes stored. If I idle it, it will smooth out, and the light goes off. All I have done so far was change the fuel filter which was almost plugged shut and the housing was full of rust looking debris which I cleaned out. BINGO! Nope. Same issue.
I am really at a loss as to where to start. I bought this with 120k on it and it now has 170k and I have not had to do anything other than routine maintenance.
Ford 7.3L Power Stroke (1999-2003) :: 2000 F250 Runs Out Of Fuel On Hard Pull / Long Hills
Every time I hit a hill, loaded or empty, or get on the truck on level ground after about 15 seconds it acts like it's running out of fuel. The pump starts getting noisy like it has air in it, but it'll straighten out eventually. If you don't let off the fuel it'll eventually stall out. No check engine light, no codes. Truck has a ts chip but it does it on all settings. New fuel filter, changed oil with hot shots secret, new air filter, hutch mod done. I'm at a loss for what to do. Good fuel pressure also.
View 8 RepliesFord 6.0L Power Stroke Diesel :: Hard To Start When Cold / Smokes And Runs Rough Until Warms Up
I have an 03 F350 with the 6.0L. It has 210,000 miles on it and the injectors are beginning to be suspect. Its very hard to start when its cold, smokes and runs like crap untill it warms up.
I've found a set of injectors out of a 2005 truck with 8000 miles on them. The truck was overboosted and blew a head gasket.
Now finally to my question.....Can the overboost damage the injector? Would it be safe to buy these and install them or rebuild them before install or just leave them alone?
Ford 7.3L Power Stroke (1999-2003) :: Rough Start At Cold?
I just started having a cold start problem with my '02 Excursion this fall and I'm at my wit's end trying to fix it. Truck starts fine above about 45 degrees and when it's warm. If I plug in the block heater it also starts fine in the cold. If it's not too cold I can eventually get it started by continuing to crank it. It blows white smoke while cranking and for a few seconds after it finally turns over. Smells like fuel. Runs rough for 30 sec after starting when it finally turns over. Definitely seems like glow plugs aren't working. This truck started no problem on GPs alone without plugging in down to -20 deg F before this year.
I started by cleaning all battery connections, including the two ground posts on the engine block, I replaced one bad battery (diagnosed by Autozone; other one was OK), I checked the resistance of the glow plugs (only a few years old with about 30k miles on them) through the connectors on the GP control module (all were about 1 ohm), and confirmed 12V at the power pins in the GP control module connectors. I then replaced the GP control module and the problem is still present. Battery voltage drops from about 12.6 V before I start the GP cycle to about 12V when I turn the key to "ON" and the GP light comes on. How much should the voltage drop when the GPs are on? What the heck else could be wrong??
Ford 7.3L Power Stroke (1999-2003) :: Rough And Lacks Power When Cold But Smooth At Warm?
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Extended Cold Crank - Run Little Rough?
For a long time I have been noticing extended cold cranks as compared to my dad's truck which has 50k less miles. Hasn't been much of a big deal until lately the crank has been getting longer to the point where it is noticeable and bothers me.
When the truck finally fires (10-15 seconds) it will sit and idle no problem, maybe a little rough, but that's about it. It will also run a little rough if you start driving it right away but will smooth out fairly quickly. When it first starts it is usually accompanied by a small puff of white smoke.
As a quick run down it has had the injector o-rings, glow plugs and UVCHs replaced about 36k ago. I can verify it isn't the glow plugs or the harness because it would start reliably down to -25 without being plugged in.
My thought is the injectors are just nearing the end of their useful lives (248k). Does this make sense?
Ford 7.3L Power Stroke (1999-2003) :: Rough Start At Cold Temperature?
I am intrigued by this engine and it's cold start issues so I am trying things out to see what works. If I plug it in it starts like summertime. If it's as cold as 30* out I run the glow plugs for two minutes and it starts without much effort and once running purrs like a kitten, no chug a lug, no romping, little smoke. When it gets down into the 20's I run the glow plugs for two two minute cycles, a little more cranking time but starts same as above. Down to 18* and I cycle the glow plugs twice for two minutes and it cranks, tries to start but won't. Key off, back on for two more minutes and it starts right up like a warm summer day. It hasn't been colder than 18* here this year so this is the end of my report for now. I haven't taken the time to check the glow plugs which is on my list but this summer it'll get done.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: After Start Up Engine Throws Wait To Start Light / Runs Real Rough And Just Shuts Off
My 99 250, 7.3 is having some strange issues as of lately. When I start it in the morning, when the engine has fully cooled down, it starts right up, then it throws the "wait to start light" runs real rough and just shuts off. Run the glow plugs a few times, start it up and it will do the same thing for maximum 30 minutes, then all the sudden I start it and it runs fine. I've replaced the fuel pump, cleaned the fuel bowl, new fuel filter, I just don't know where my problem could be. It doesn't make sense. But once I get it running and it warms up, runs fine all day. Go to bed, wake up, has problems again.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: CEL / Rough Running / Smoke Blowing When Cold
I had been fighting some problems with injectors for several years. I didn't have time to dig into it. I knew what I needed to do, just needed to find time to do it. I honestly thought it was and injector and thought I would have to go to new sticks because I've had so many problems with the remans.
Well I finally had time last week. I pulled the passenger side valve cover and ohmed the injectors. It would be almost impossible to get the leads in the injector while installed the truck. I kept an old valve cover harness, so I cut a pig tail off of it and plugged it into the injectors so I could test. You can see the meter attached to the pigtail in the pic.
To my surprise all four were all right around 2.7 ohms. You need to set your meter so you are getting a reading w a decimal. If you set it to high it will only show a whole number and it is better to have a more accurate reading.
I then plugged the wiring harness back in and tested it from there. The #7 injector gave over 6 ohms. This told me that my wiring harness was bad. I went OE and replaced it. I had a problem w a Dormant valve cover gasket before so didn't want to go that route. After I replaced the gasket and harness all my readings were under 3 ohms. They were all lower than w the old harness.
Ford 7.3L Power Stroke (1999-2003) :: 2002 - CEL - Rough Idle - Loss Of Power?
I have a 2002 F-250 7.3, 159k on it. I bought it in March, ran AWESOME up till now. I was driving to work last week, check engine light came on, truck lost power and started idling rough. I have a buddy who works for a Ford dealer as a diesel mechanic, he came over with his scanner and laptop. #2,#4,#8 cylinders kept coming up saying possible problems are injectors, harness, rings.. He also did an electrical check, that all checked out. He told me to get injectors, so I got 4 injectors (yes I got the correct #8 injector), valve cover gasket, injector harness and 4 glow plugs.
The parts came last Friday, we did the job and it ran great. Drove it Friday night, Saturday, Sunday morning, no issues. Sunday afternoon we were on our way to a birthday party, truck started doing the exact same thing... Check engine light, rough idle, loss of power. After I got home from the party, my buddy came back over, put it on the scanner again, getting the same codes again. Deleted the codes, ran the tests again, same codes, deleted the codes, rant the tests again, same codes.
He said he is going to come by tomorrow with the box to check each individual cylinder.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F350 - Rough Idle / Lack Of Power
I have a 2002 F350 4wd with the 7.3. I was driving the truck and all of a sudden it was running like crap. the engine light was on. after a minute or so the engine light goes off and the truck is running fine. then again starts running like crap. I am close to the house so I limp it home. runs like crap.... will barley climb small hills. engine light is on. get home turn it off... next day... starts up and runs great for 10 - 15 min. engine light comes back on... runs like crap.... my neighbor says "It's the crank position sensor" I replace it.... runs great for a month.... now it's doing the same thing......
View 9 Replies