Ford Super Duty (1999-2016) :: F250 V10 Missing And Lacks Power To Accelerate Further
I have a 1999 ford f250 with a 6.8 liter v 10 engine. At about 40mph the truck will start missing and lacks power to accelerate further. This problem is intermittent. Some days it runs great and others the miss appears. Well I scanned and the code reader said that I had a misfire on cylinder 7. I took a chance and replaced the COP and the boot for that cylinder . Ran great for a day and then the miss came back. Same code again. What else might cause this? Are plugs difficult to change in these engines?
View 6 RepliesFord Super Duty (1999-2016) :: 2005 - Idles Rough - Lacks Power?
I have a 2005 f250 with a 5.4 3v. I bought the truck with a cracked passenger side exhaust manifold about a year ago. We'll here recently the crack got worse and was giving the code P0171, so I had a shop replace it. I picked the truck up and not even a mile down the road it started idling terrible at lights and had very poor acceleration. And it gave me P0174 this time. It's only gotten worse now it's reading P0172, P0174,P0161, and P1489. I've replaced the spark plugs, MAF sensor, both vct solenoid, an the upstream o2 sensor on the passenger side. I also know I don't have any intake or vacuum leaks, I've had a shop check and so have I. It's starting to get expensive just replacing stuff. So, maybe I have a clogged catalytic converter ?
View 8 RepliesFord Super Duty (1999-2016) :: F250 5.4L - Stumbling And Loss Of Power
One of my work trucks is a 99 F-250 5.4L. Up until recently it's been running strong. Then one day it's like someone flipped a switch, and now it runs like it's losing power.
Symptoms: a quick short stumble when you first hit the accelerator. While driving, it takes the entire pedal to accelerate. Even with the pedal to the floor, it won't keep up with traffic. Driving uphill, it will barely maintain 40 mph.
I've checked everything I can think of. Fluids and filters are all good. Battery and alternator are good. There are no trouble codes. I have Autoenginuity with the Ford Bundle, and the truck passes every diagnostic test I throw at it.
There's no smoke. It still idles pretty smooth, although there is a slight and very quick random shudder in the idle that has started at the same time it started losing power.
Transmission is good. The last thing I tried was to change the fuel filter, but that made zero difference. Quick question, does the tank on the 5.4L trucks have a pickup screen like the diesels? If so, I might try blowing some compressed air through the fuel line and see if it dislodges anything.
So that's where I'm at. It has no power, yet I can't find a single thing wrong with it.
Ford Super Duty (1999-2016) :: Morning Time Grumble / Truck Stumbling
I'm assuming I might have a coil going but I'm not sure. Yesterday morning and this morning I started my truck and it was fine, I backed out the driveway again truck was fine. I put it into D and pull forward it was fine till I hit about 1300rpm, then it felt trike the truck was stumbling, I went a little faster to 1500/1600rpm and it stopped, as soon as I slowed up and then hit the go pedal it started again at around 1300rpm and stayed till 1600rpm and then it went away. So this is twice now two days in a row this has happened the exact way and only in the morning and goes away with no problems. I hooked up my SCT X3 and there are no codes and when it stumbles I have no lights come up. What I should do?
View 14 RepliesFord Super Duty (1999-2016) :: 2008 F250 V10 Missing / Dead / No Power And Multiple Codes
I have a 2008 f250 superduty with the v10. Just today I was driving and engine picked up.slight miss it's rainy. I thought coil pack, but it left me on side of road. Got fired limped home won't go more than 40mph. Runs rough, no power, checked codes and get P0340, p0357, p1336, and P2195.. Where to start.. My daily driver and have to get back on road.
View 1 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Intermittent Power Loss / Bogs Down To 40 Mph Then Starts Missing
My truck is a 2003 f250 / 2wd automatic, 7.3 powerstroke, 284000 well maintained miles.
Just last week I sprug a large oil leak and had to replace the hoop outlet o rings..problem solved. This week I can drive 15-20 miles on the freeway and the truck starts to act like ota running out of fuel. Bogs down to 40mph then starts missing. I pull over, and when revving I have un burnt fuel and oil smoking out of my tailpipe. I let it sit for 5-10 minutes and it will be fine for the rest of the drive and this happens intermittently, there is no pattern.
The truck has a ton of power, starts great hot or cold. I did a ton of research and found a IPR could possibly cause this, as could plugged screens in the fuel pickup. Then I read about all the injector harness issues but I don't think that I my issue.
Ford Super Duty (1999-2016) :: 2005 F250 - Multiple Misfiring Codes / Stumbling When Come To A Stop
My '05 F250 (5.4) started misfiring and threw codes for p0300, p0305, p0307, p0308,and p2198. I used an inline spark checker to check cops, which all had spark. Replaced 5, 6, 7, and 8 plugs and cleared codes. Ran truck for a few minutes and codes came back. Switched #5 and #6 cops and cleared codes. 5,7,and 8 cylinders still misfiring (same codes). Truck only has 36,000 miles and spent alot of time just sitting. Plugs were original plugs.
Replaced 5-8 with Autolite OEM replacements. I haven't checked cops for resistance yet. Weather was pretty cold when problem started. Threw in about 10oz. of Lucas to no avail. I had this problem last winter with the same cylinders throwing codes. Threw some Lucas in the tank and idled truck for approx. 1/2 hour and problem went away except for stumbling most every time truck came to a stop. I'm starting to wonder if it's a coil or a fuel issue.
Ford Super Duty (1999-2016) :: 2000 V10 Missing At 40 - 45 Mph
Have a 2000 F-250 V-10 4x4 with 335,000 miles on the clock. Has started hesitating at 40-45. You can't really notice it at idle. Drove it around at lower speeds and just a miss here and there. Take it up to 40-45 and it's quite bad. Hasn't thrown any codes. Hooked it up to the scanner to get no additional info. My gut says coil packs but am kinda confused that I haven't gotten a misfire code yet. What to check?
View 6 RepliesFord Super Duty (1999-2016) :: F450 Missing When Cold
My 99 f450 7.3 runs bad on first start of day. I checked the codes 3 codes p0475, p0470 and p1247. Now here is what I tried I plugged it in over night and it will start and run as should the next morning with out side temp 47. Drove the truck late yesterday evening didn't plug up tried it this morning with a outside temp of 47 truck starts but missing and like of power. My problem seems to be temp related. Will low boost pressure cause this problem what do I need to do?
View 4 RepliesFord Super Duty (1999-2016) :: AC Compressor Missing Clutch
Ok AC wasn't working took it to a mechanic told me the the compressor was missing a clutch he recommended i put a new compressor. Is it possible just to put a new clutch in it and if so do i have to remove the compressor to put the clutch on it.
View 14 RepliesFord Super Duty (1999-2016) :: Truck Missing Bad After It Warms Up
One day after my mechanic replaced the heater core my truck started to misfire after the motor warms up and is under load. No codes and nothing pops up when hooked up to o a scanner. It's been cold in the morning and when I start it up it runs like a top. But after it warms up it start to miss a little, then it gradually gets worse especially when under a load at higher speeds. I thought it was a vacuum hose or something got left unplugged.
View 7 RepliesFord Super Duty (1999-2016) :: Locking Hub Pieces Missing
I went to replace my driver's hub bearing last night. Found pieces missing from the locking hub (manual). I ordered them last night it's the snap ring and washers but will not be here till next Monday. Can I run the new bearing with out hurting it. It has already ruined the seals on that side I just don't have the time to take it all the way down. So if I install the bearing and don't put all the guts in the locking hub (I know the locking hub won't work) Dont need 4x4 right now but need to be able to drive it some. Just don't want to mess up the 250 dollar bearing I just got.
View 2 RepliesFord Super Duty (1999-2016) :: 2003 - Missing Under Acceleration
2003 6.0 is acting crazy again. Has new ICP, IPR, oil discharge tube, and hpop. It cranks right up but one time you crank it and all the gauges work correctly, especially the fuel gauge. The engine will idle perfect but when you accelerate it has a dead miss. May crank like that 2 to 4 times. Then you crank it and it runs like crap, and the gauges won't work, the fuel gauge goes past E and the light comes on. As long as that happens it runs terrible, but when the gauges are working it idles great but has a miss under acceleration! It was running fine, then just went nuts!
View 4 RepliesFord Super Duty (1999-2016) :: 4x4 - Front Hub Missing The Manual Lock
Just bought a nice little project 1999 4X4. 100k miles and overall decent condition.
One of the first things to tackle is the driver's front hub has no manual 4x4 locking mechanism like on the passenger side. Is this a tough job?
Attached is the picture of the hub & missing lock setup. (Can't upload...).
Ford Super Duty (1999-2016) :: 2003 - Missing At Higher RPMs?
I have a 03 F250SD with ~145,000 miles on the 5.4L. Just recently I have been having what seems to be a miss, or possibly a dead cylinder. I thought it might be a dirty MAF, but I cleaned it and have the same problem. The miss is more noticeable at the higher RPMs. I am checking the plugs today. So any solution? I refuse to take her to the shop and having another man up in her manifold.
View 8 RepliesFord Super Duty (1999-2016) :: F350 Missing At High RPMs
I have a miss at high rpms.. I pulled this engine, manual trans, and 4x4 axle and put them in my F350 Majestic motorhome. 156,000 miles on the engine. Slightly dusted engine with good compression 375-400 (cranking and corrected for altitude). Has a little bit of a long start.
No smoke on start up unless 10 degrees or colder
No smoke when pulling either.
Glowplugs ...Good
GPR... Good
Checked resistance from IDM to injectors ...Good
History of some ether for starting before I got my hands on it. I have AE with the ford enhancement. But I am new to working on a powerstroke and new to AE.
ICP ...new
CPS...new
Oil ....new
EBP...new
Installed a pressure gauge to the drivers side upper port on my fuel bowl:
60 psi at idle
55 psi at WOT 2500-3000 rpms under a load
HPOP stabilized pressure is 2750 @ 40% duty cycle
Truck still misses (semi-intermittently) at higher rpm with a load.
Rechecked codes KOEO: None present
I visually inspected valve movement while running (idle). Did the buzz test when cold.... All injectors sounded the same when tested individually.
Did a cct when not completely warm:
P0266
p0272
Repeated the test at normal operating temperature:
P0266
Torque values on rocker arms bolts and injector holds are good. Fuel quality isn't an issue since this problem has remained for 5 tanks of fuel. What I should do next?
Ford Super Duty (1999-2016) :: Missing Bad When Started After Sitting Overnight
This is an update on an older post I took the truck to a repair shop and had it checked. They said 5 of the 8 glow plugs were not working and #3 injector was bad.. They replaced all glow plugs and the #3 injector I brought the truck home and parked it about a 20 mile drive home running fine when I got home. When I started it the next afternoon it was missing just as bad as before the work was done. After it gets warm runs ok best I can tell. What it could be? If the orings on the injectors are bad would it run ok when it warms up? Going to take it back to shop but not sure they know whats wrong by the way the mechanic talked. What to do next they have checked the wiring or at least said he did. It does ok when the oil warms up new hpop and I have checked the oil level and it was ok the hpop and eng. What else to do?
View 1 RepliesFord Super Duty (1999-2016) :: 2004 F250 6.0 - Missing At Idle?
I have a 2004 F-250 with a 6.0 and a 6-speed with 140,000 miles. It has been studded, and has upgraded injectors. ( Not sure on the size, they bored them at at the diesel shop that studded my heads.) Also have an EGR delete, with the EGR turned off on the SCT as well. I also have a SCT Livewire set on the 65HP tow tune.
Truck has always ran great in the year and a half I have had it. I changed the oil three days ago, and now I am getting a miss at idle. The trucks cranks right up and drives normally. Once it is at operating temperature, when I stop at a light it has a very noticeable miss. There is no surging, or change in RPM's at all. Just seems like it is cutting out every few seconds. This is also somewhat intermittent. FICM shows 49 volts always, even when this is occurring.
Also, this may be unrelated, my oil temperature seems higher since the oil change. Was around 192 water/197 oil while cruising 70 on the interstate. Now, its' more like 192/202. I've always ran Motorcraft 15w-40, and that is what I used for this oil change as well.
I see some people have a similar problem, but all the posts I've read involved fluctuating RPM's or surging, or both. Other than this, the truck cranks and runs just like normal.
Ford Super Duty (1999-2016) :: Missing Some Brakes - Pedal Is Extremely Spongy
I'm not exactly sure what's going on but it feels like I'm missing some brakes - the pedal is extremely spongy, I have to push it nearly to the floor. And when they do engage, it isn't with the same vigor as they did before.
It's strange, it just sort of happened - I drove to a friend's house, everything was fine. But when I left all of a sudden, there's this problem.
It's not like the pads have come apart and destroyed a caliper - I had that happen to me a few years ago and I definitely felt it happen, plus once it did I lost almost all braking ability as the lines would just leak fluid.