Chevrolet - Corsica :: 1994 - Cannot Get High Beams To Come On
I recently purchased a 1994 Chevy Corsica that is in excellent shape for the year with one exception. I can't get the high beams to come on. When I pull back on the turn signal lever, nothing happens. I know that most of them make a "click" noise when you pull on them, but this one doesn't. Is the high beam switch a part of the turn signal switch that is in the steering column? I am not sure what else to try.
View 4 RepliesChevrolet - Corsica :: 1993 - Cylinder 4 Has No Spark?
A friend of mine has a 93 Corsica with the 2.2 liter engine. His #4 cylinder has no spark. #1 and #4 share a coil and #1 has spark. Also #2 and #3 are ok. He has replaced the coil for 1&4 and also the ignition control module but still only has spark on #1. The wires are new and test ok. How you can have spark on one side of a waste spark system?
View 1 RepliesOldsmobile - Starting - Intrigue - Rough :: 2000 - Idles At Non Regular Number?
I don't know what is wrong with this car, I have put in new titanium plugs, new plug wires, new fuel filter, new air filter, changed the oil, I burn mid-grade gas. The car starts right up when cold, however once it warms up it idles on a non regular number, dies when driving and is very hard to start. I get lousy mileage and it smells like it is either not getting enough gas or not getting enough air. I don't know what else to do. I had it analyzed with an electric analyzer, no codes were found. When the plugs were put in the air flow sensor had either gas or oil on it. It does not use any oil.
View 1 RepliesChevrolet - S-10 :: Truck Idles Rough And It Gets Worse When Its Rainy And Damp
At first I thought it was a vacuum that was causing all of this.I was getting a (small leak) code I replaced the vac tubes and the code still came back. But that is not the main problem.I had two problems at the same time I just didn't know it. A vac leak wold not make it run this bad. I had just recently put in new plugs and found one plug loose. It was easy to take out and didn't need to be broken free. The plug was fouled out bad (black) the other 4 were good. It must have been the loose plug all a long that was giving me problems.
I drove the truck a while before I checked the plugs,I had no clue it was loose. When the plug job was done,it ran well (because engine was warm) the next day with a cold start it ran bad,real rough. I was thinking that the loose fouled plug caused the coil pack to over load and go bad.. Now when the weather is wet it makes it way worse. At least when it is dry I can drive it. Do you think the coil packs could be the problem creating the missing and rough idle??
There is only 70k on the truck I bought it new in 2002....
Nissan - Altima :: 1995 - Rough Idles And Shuts Off When At A Stop
I have a 1995 Nissan Altima GXE 4cyl and it has been rough idling for a while now but now I have this new problem. While I drive the car and after it has warmed up, the car shuts off when I'm at a stop. When I'm at speed, it runs just fine and smooth and I only have problems at stops. I then restart the car just fine and continue driving. I'm having to keep doing this over and over. What could be the cause or causes for this?
View 4 RepliesPrius (2004-09) :: Engine Will Not Stop Idling And Idles Rough
Just picked up my 2004 Prius from the Toyota dealer body shop. The driver's side was scraped by someone who wanted to be in my lane. Fortunately, we were only going 35 mph. The rear door skin had to be replaced, and most of the side had to be prepped and painted. There are a few silly mistakes: they forgot to replace the driver's door plug, forgot to replace a lower clip, and smudged a tiny area new paint on the bumper. I brought that to their attention and they are going to take care of it... they have to order the plug and clip.
However, as soon as that conversation was complete, it was time for them to close shop. I sat in my Prius, started it, and the check engine light was on. Wasn't on when I dropped it off for the repairs. Also, on the way home, I noticed the engine wasn't turning off when I came to a complete stop (even though the animation says it was off). At idle, the engine is also rough. Looked at the charge bars, and well, there were only two bars showing.
I thought perhaps, though it's not done this before without the animation screen showing it, the engine was on merely to recharge the traction battery. On the way home, the traction battery returned to full charge (green), but the engine still was not turning off when the vehicle was at a complete stop... not was it turning off when coasting... and when arriving home, even with the car in park... and still idling rough. All the while, the animation on the screen is indicating the engine should be off.
When I replaced the traction battery three years ago, I also replaced the 12v with an yellow top Optima. I wouldn't think the Optima is already going bad. I also do not believe in coincidence. I wonder if perhaps some bad fumes have tainted the MAF, or who knows.
Ford - Focus :: 2011 - Idles Rough When Come To A Stop, In Drive
When I first start out driving the car, and come to a stop, in drive, the car begins to run rough. I can hear and feel the vibration, it's very noticeable. I put it in neutral and it stops. As I load the engine with AC or use the electric windows it seems to gets worse. Then after driving for about 5-7 miles, it quits. Primarily in cold weather, since it started 4 months ago. I do allow the car to warm up before driving.I'm still under warranty, and have been to the dealer 3 times. Of course, it doesn't happen when I go to see the dealer. But they did re-tighten the motor mounts. I don't think it worked.
View 12 RepliesCamry :: Grinding Sound At Around 1400 - 1600 RPM / When Starting From A Dead Stop
I have a 2001 Camry LE, 4 cyl, 2.2 liter, automatic transmission, 163Kmiles on it.
I'm hearing what sounds to me rather like a grindy sound at around 1400-1600 RPM. Initially the Camry seemed to do it only after getting into 2nd gear at about 10MPH, but now i see that it is associated with RPM and not the gear so much (the noise is less frequent and less loud in 2nd and 3rd gear- not noticing it ever at above that). I should say that the Camry has been making lots of noises since a new exhaust was put in by a cheap Bosnian shop.
It seems to only make that particular grindy noise when starting from a dead stop, but not if i was already coasting at all. So far as i can tell it seems to only happen about half the time- if I'm accelerating very slowly it doesn't seem to happen much. If i start climbing a hill after a dead stop it seems to come on fairly reliably.
It does not seem to make the noise when passing down through 1600 RPM while slowing down or revving down.
When i started the Camry up today, the noise cropped up well before i got to 8MPH (where it typically shifts into 2nd gear). Which is to say the noise appeared before it even started to shift out of 1st gear.
If i stay in Drive or Reverse and apply the brake so as to not go anywhere, the noise generally starts around 1600RPM. Since the car isn't moving, i think this might rule out the transmission. I hope.
However when in Neutral or Park and i bring the engine up to 1600RPM and beyond, the noise does not appear. So that's perhaps not so good. Of course my car idles a lot better/smoother in N and P than it does in D or R. It's rather rough idling in D and R.
I'm hoping maybe it's a vibration issue- something like harmonic amplification- where something only rattles in a certain frequency range. I pulled up next to a brick wall, kept on the brake, went into D and got up near 1600RPM and the reflected noise does strike me more now as maybe being less a grindy noise and more of a rattly vibration.
The Bosnian shop who fixed up my exhaust were too quick to dismiss the noises i heard after they worked on it. I think maybe something is loose. I hope. (I could feel air leaving the flexpipe's woven area itself but don't know if this is normal.)
Going up hills increases the likelihood of the noise appearing (so i take this to be suggestive that it IS the transmission).
However on a flat road if i hit the gas to quickly get up to 1600RPM before I'm any where near auto shifting out of 1st gear, the noise also usually appears (so i take this to be suggestive that this is not the transmission). I've also gotten the noise to not appear until well into 2nd gear.
The fairly-repeatable noise appearing in the 1600RPM zone regardless of my gear position gives me some hope that the xmission is not the source of the noise. So on balance, i think there's some indication it's the transmission, but there's also evidence that the source is other than the transmission.
The noise does not occur in Neutral or Park while revving up to 1600RPM. But then too, the engine, exhaust and vibrations always seem considerably less in N or P, as opposed to being in Drive (or Reverse). Why my Camry is quieter and more smooth in N and P as opposed to D or R? In the latter two modes, i imagine the transmission is engaged? And that the transmission is unengaged in P and N? And would that make the car louder or vibrate more, at least under certain conditions? Is the engine under less load in P and N?
And are noises at certain RPMs in D or R, but not in P or N indicative of Transmission problems? I notice the shop overfilled the transmission fluid every time i've had it changed.
Santa Fe (CM - 2007-12) :: 2011 - V6 Idles Rough At Red Light / Stop Sign While In Drive
I have really taken care of this 2011 SF Limited with the 3.5 V6 but it has always seemed to idle rough at a red light/stop sign while in drive. Is this common for all the 3.5 V6 engines? I run a fuel cleaner through it before every syn oil change and also use top tier gas. It drives nice but like I said, at a stop in drive it seems to run rough at around 500-550 rpm's.
View 10 RepliesChevrolet - S-10 :: 1992 - Idles High / Stumble When Driving
My 1992 chevy s-10 is running really bad it idles high ( like around 2000 rpm to 1000 rpm) it starts high then slows down. Then when i drive it, it kinda stumbles. Iguess u can say it makes all kinds of noises and beats and bangs and if I am going up a hill some times it shuts off. It has a manual trany and a stock 4.3 motor. I need the truck to get back and forth to work....
View 3 RepliesImpala - Chevrolet :: 2005 - Gas Smell Both In And Out Of Car When Idles But Only After Some Driving
There is an odor when it idles both in and out of the car but only after some driving - if I sit there a while the smell goes away. It is most noticeable when I get off the highway on my way to work and sit at a stop light. If i have to sit and wait for someone, the smell dissipates. I cannot find a leak. There is a performance issue but I'm not sure if it's related. At highway speeds it is having trouble accelerating - if I'm at 55 and want to go to 65, it'll go but it feels like there's resistance, almost a pulling, it causes the car to rock back and forth a bit - again it only happens at higher speeds. It has 140000 and is in good shape (except for things mentioned). The last repair was a water pump replacement about 4 months ago.
View 3 RepliesDodge - Dakota :: 1988 - Stumbles At WOT / Truck Only Idles
I have an '88 Dakota, 230K miles, with the following problem:For the last month or so, the truck has been hard to start--had to crank once, wait 10 seconds or so, then crank again. Gradually, this problem increased to the point where it would stumble at WOT, then even at 3/4 throttle or so.Thinking it was the fuel pump, I replaced it, along with the filter.
Problem remains; in fact, it seems even worse, to the point where the truck only idles (can't put any load on it, or it stumbles). So, at this point I suspect the fuel pressure regulator. However, I don't want to buy it unnecessarily. Given that a F.P.R. is designed to send a part of the pump output back, would pinching off part/all of the return line be a valid diagnostic test?Anything else that comes to mind?
Dodge - Dakota :: 1996 SLT Idles Rough / RPMs Will Drop To Near 0 Within About 20 Seconds Of Coming To A Stop
So I have a 96 Dodge Dakota SLT 3.9 4WD. Anyway, it idles relatively smoothly at about 700 RPM in drive or neutral, but if I'm in a moving gear and need to stop, the idle is extremely rough. Usually, the RPM's will drop to near 0 within about 20 seconds of coming to a stop. It will typically recover and continue with rough idling and near stalling a few times, but within a minute or two it stalls. A few additional details: it starts right up again after falling, it doesn't make any difference if I start it cold and drive immediately or drive it for an hour before coming to a stop, the same thing happens. Anything that looked suspicious to me has been changed (drive belt, spark plugs & wires, distributor cap & rotor, pcv valve, idle air control valve, and, of course, the air freshener).
View 1 RepliesAccent MC (2006-11) :: Misfire / Car Stumbles On Acceleration And Idles Sporadically
After almost an entire year of trouble-free running (with the exception of replacing a ground strap), my 2009 accent decided to start bucking and shuddering again. It only does this when warmed up, runs perfect cold. In the last 16 months, I've replaced the plugs, coils, battery, PCV valve, and ground strap. Car starts with zero hesitation.
Strong battery and starter, consistent output from alternator. After @5 miles, the car stumbles on acceleration, and idles sporadically. While looking at it tonight, I noticed a few exhaust brackets under the car had broken, and the flex section of the intermediate pipe had torn open. Could this presumed exhaust leak be causing the crap running performance?
My "exhausted" brain thought it could cause the O2 sensor to misinform the ECM, resulting in the P0300 code I pulled...
Chevrolet - Blazer :: Truck Went Completely Dead At Stop Sign Now Just Cranks
I have a 2000 S10 Chevy blazer .One day I was at a stop sign when the truck went completely dead , I had no power . I walked home , I came back a little later and figure I would give it a try well it started so I brought it home .. from then on it would start up some days and other times it would just crank but not start .After keeping it my garage for over a year , the other day I charged the battery and try to start the truck , it kicked right over and I let it run for awhile . I turned it off and restarted it again let it run for awhile . Yesterday I went up to start it again and nothing ,so I gave up , today it was the same thing it would just crank but not start . I know its not a fuel issue , and I don't think its an ignition problem ..
View 5 RepliesChevrolet - S-10 :: 2001 Pickup Went Dead While Driving
My 2001 Chevy S10 Extended Cab Pickup 4 Cyl 102K miles went dead immediately after pulling out of my parking space. Went about 10 yards and all of the sudden the engine, power, dash lights, everything shut down, requiring me put into Neutral and push to side of the road. One minute later, it started up just fine and got me through the day with no further problems. The NEXT day, on first attempt, I turn the key half way and all power and dash lights come on, but as soon as I try to turn the engine over, everything went dead and remains that way. It is currently in this state. I replaced the battery 4 months ago.
View 2 RepliesNissan - Sentra :: 1987 - Idles Real Rough At Times / Hesitates At Stop Signs / About Stalls Out When Press Gas Pedal To Go
I have a 1987 automatic Nissan Sentra XE- two barrel carburetor, mileage 212,880. The car has one major problem that is going to get me hit driving it in rush hour. Most mechanics will not touch the car due to being carburetor.
Let me explain: the car idles real rough at times, hesitates at stop signs and red lights, about stalls out on me when I press the gas pedal to go or when I start to make a left or right turn. However, other times the car has little to no hesitation and idles perfectly. I have not been able to come up with a good a pattern with this problem.
I have replaced, fuel pump & filter, spark plug wires, coil, distributor, ecu computer, ran sea foam through the fuel system and have replaced many vacuum hoses.
Ford Super Duty (1999-2016) :: 2001 F250 - Rear End Slip / Bump When Initially Starting From A Dead Stop
I am experiencing what feels like a "bump in the rear" when initially starting from a dead stop. It feels like a car behind me tapped the bumper or that the truck "hunkers down" first, then moves. Tranny seems fine also. Once moving, there is no problem whatsoever. There atre no noises, leaks, or other symptoms. Also, when coming to a stop, it feels the same way just before the truck completely stops. If I drift forward a little, then apply the accelerator, it does not "slip" or hunker down.
Took it to the dealer and they claim that they can't find anything wrong and may just be the suspension releasing? The truck does this whether loaded or not?
2001 F250 CC Lariat SB 7.3
Toyota - Tundra :: 2003 - Hesitation When Try To Accelerate From A Dead Stop Or While Driving Along
I have a 2003 Toyota Tundra V6. The problem I have with it is it hesitates. It does not happen ALL the time but it is very frequent. Sometimes it happens when I try to accelerate from a dead stop and other times while I am driving along (does not matter what speed). It will usually hesitate for a few seconds then everything is normal. The check engine light thus not come on.
I took it into Toyota. They duplicated the problem on the first test drive but did not have their equipment hooked up at the time. They kept the truck for over a week and finally got it to happen again. I guess they must have only been going on short test drives because it happens to me multiple times a day. They told me it was the throttle body and it needed to be replaced. My jaw hit the floor when they told me how much they charge to replace it. I ran this by a couple of friends who work on cars on the side and they said it sounded like the mass air flow sensor needed to be replaced. Since this was much cheaper than a throttle body, I replaced that. However, it did not solve the problem.