Sonata I45 (YF - 2011+) :: Rear Sway Bar And Links Installation
I just installed rear sway bar & links, this made a world of difference in the way the car handles as soon as I made the first turn I could feel the difference in the car it definitely corners flatter, the install only took about an hour did it in the driveway on ramps, I installed the kia sway bar 555102T000 the bar is 18.3 mm while the stock one is only 15mm I included some pics...
View 8 RepliesFord - Explorer :: 2000 - Front Sway Bar Links Coming Apart?
One is coming apart, so I'm gonna replace the pair. My Chilton book says to jack the front end up. The part instruction sheet makes no mention of doing that.
Raising the front would allow the control arms to hang. That would seem to me to make it harder to deal with the links.
Ford Excursion :: Hellwig Sway Bar Links Work With Oem Sway Bar?
Can the hellwig sway bar links will work with an oem sway bar? I need new ones and figured why replace with something I know will fail early...
View 3 RepliesHonda - Cr-v :: 2005 - Loose Sway Bar Links
The Honda dealership told me my 2005 CRV has loose sway bar links. How are these fixed? They quoted a price of $290 for the front links and $374 for the rear links. Does this sound reasonable.
View 14 RepliesCamry :: 2005 - Change Front Sway Bar Links?
I want to change the front sway bar links on a 2005 Camry that has been driven in central New York (ice, salt, corrosion) for 10 years. There is definite wiggle and noise. I recently replaced the ball joints. That was difficult. How difficult is it to remove the sway bar links? Looks like a 5MM or so allen wrench is supposed to hold the ball joint type link to allow 18MM nut to be removed. A 5MM allen wrench is about 4 inches long and skinny. An 18MM wrench is about 12 inches long and beefy. I am skeptical about breaking the nut loose.
Will I need to heat the nut? If yes, how? With a simple propane torch? If yes, how does that work? Apply heat and wait for a sound that indicates the rust has broken? Apply heat for a time, try to hold with the allen wrench and try to undo the nut? Keep trying that again and again until it works? This would be after multiple rust busting spraying to make this easier. I used a 4 inch grinder to grind the nuts off the ball joints to remove them (I know how that sounds, but that is what I did). Thoughts about that for the sway bar links? I am a bolt turner who can stand some aggravation.
Prius (Gen 2) :: Front Sway Bar Links Making A Bad Noise
Both of my front sway bar links have a bad joint and are making a bad noise.. I purchased the replacements and tried to loosen the nuts with no success. I put some oil to loosen them and will let them set over night. Next attempt will include a breaker bar.
View 4 RepliesJetta - Volkswagen :: 2002 - Broken Sway Bar Links
My mechanic says I need to replace both front sway bar links on my 2002 Jetta....I am, of course, hesitant to do it at this price. How critical is it to replace? Can I get junk yard sway bars to make it cheaper? And can I do it myself (have no experience fixing anything....
View 11 RepliesFord Excursion :: Sway Bar End Links / Loud Clunk
I've been having the loud clunk under the drivers side floor, that many others have as well. Did many hours of research and replaced the sway bar end links. Napa only had the left side in stock so I did it first last weekend and did the right side this weekend. One thing I noticed when doing the right side was the hole in the frame was all wallowed out. Drilled out the bushing in the upper end link and used a bigger bolt to fill the gap up. went for a drive and the clunk was way worse than it ever was still on the left side. So I took off the left one and went for a drive. Sure enough no clunk, the left one was wallowed out as well. So I did the same thing on that side and the evil clunk is finally gone. Just thought I would throw that out that if have a clunk after replacing the end links, Check the upper holes.
View 14 RepliesFord Excursion :: Clunking Noise - Front Sway Bar End Links
I plan on replacing as I have a clunk happening. Thought I'd try here first.
Is there a brand that's better? 1Aauto has OEM. Is there a brand that's better or makes a difference?
Or is a front sway bar end link a front sway bar end link?
Ford Excursion :: Correct Length Of Front Sway Bar End Links
What is the correct length of the front sway bar end links. I need that info to order replacements for my 04 X EB 6.0 4x4. I just don't want to wait another day.
View 3 RepliesFord Ranger / B-Series :: 1993 - Front Sway Bar End Links?
I'm new to the whole Ranger truck thing since buying a 1993 Ranger 4x4 for my 14 y/o son. It has a 4 inch suspension lift and a 3 inch body lift running 33x10.5x15 tires. The front sway bar is not hooked up. I know that i will need drop brackets for the sway bar but my question is about the end links needed for this truck. There are 2 tabs with provisions for a horizontal bolt on each side of the twin I-beam where the end link would attach and the sway bar has a single horizontal hole on each end. Searching for replacement links at various auto parts websites only seems to yield the standard end links that consist of a straight bolt with a nut on each end and the rubber insulators. That clearly is not the correct end link for my application. Not sure if the front suspension is the factory installed unit or if it was swapped some time in the part.
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Sway Bar Links Not Correctly Lined Up?
So putting the new extended links on my truck, not sure if they are supposed to be seated flush on both the frame and sway bar itself before tightening them down. This is how they are sitting now --
You can see a little gap between the rubber fitting where the bushing sits and the frame mount. Just wanted to make sure before I torque it down. Its the same on the other side as well. They are sitting flush on the sway bar.
Ford Super Duty (1999-2016) :: Greaseable Sway Bar Bushings And End Links
I have a 2002 F350 4x4 CC 7.3 i am wanting to change the sway bar bushings front and rear to poly and I want greasable bushings to avoid the squeaking that you get with these bushings alot of the time. I would like to change the end links to poly too i realize these wont be greaseable. What was the outcome and where did you buy the bushings. What is the size of the front and rear sway bars and the length of the end links??
View 14 RepliesFord Super Duty (1999-2016) :: Sway / Stabilizer Bar Links Rattling?
I'm on my second set of links. The replacement were Dorman 3 years ago. They are rattling again. Do I just replace them again? I forgot to add, the bushings were replaced this year.
View 1 RepliesFord - Taurus :: 2000 - Wheel Alignment / Changing Struts
My 2000 ford Taurus which has 120,543 miles needs an outer tie rod end. I went to sts for an oil change and asked them about an alignment after I did the tie rod and they told me I need to change my struts. If I only change the front struts could I get an alignment or am I going to need to change the rear also? Also, i know I have to get new tires in the front because they are getting bad from the alignment being off so I would have to get tires also.
View 6 RepliesFord Excursion :: 2004 F350 - Front Sway Bar Links Keep Wearing Out After 3 - 4000 Miles?
My 04 6.0 Limited and both front and rear sway bars. The front links keep wearing out after 3-4000 miles. But, I saw someone in here put F350 Sway Bars in their Excursion? REALLY?? Is this right or is this snake oil? Is their another way to fix the front links so they don't wear out so quickly??
View 4 RepliesPassat (B5) :: Changing Sway Bar - Can't Get The Bolt Out
I did change my motor mounts this weekend but when I tried to remove the sway bar,one of the nuts jammed on the bolt. Let me explain:The nut unscrewed well until the lasts mm, and then, the bolt head came loose, so it was spining freely with no way to remove it but cutting it, the bolt seems to be BUILT IN the alum. bracket that supports the engine mount. Question: can I change this bolt or is it really built in the bracket? I searched on ETKA but it just shows the nut and I can't find the bolt that I need.
View 1 RepliesPrius (Gen 3) :: Changing Front Sway Bar Bushing With PU Version?
Trying to change the front sway bar bushing with a PU version? Does it improve handling and steering feedback?
View 1 RepliesPassat (B7) :: Changing Tires - Wheel Alignment
As the weather has been getting warmer lately, I'm about to change over to my summer wheels and tires. First, I'm just wondering when most people who use winter tires on this forum make the change.
On my previous cars, I've just changed over in the fall and spring by myself unless I needed a wheel balance or alignment. With the harsh winter and roads we've had this year, I'm thinking maybe I've hit too many potholes, since I'm noticing a vibration at 140kph (87mph). I got the current OEM rims and winter tires new last October and had them balanced before installing them on the car and I hadn't noticed anything until about 2 weeks ago. The issue did not suddenly show up after hitting a pot hole, but just started happening and becoming a bit more noticeable recently. The weird part is that it seems to be happening only at that specific speed when accelerating, which makes me wonder if its the wheels out of balance or engine/turbo vibrating under load. As you can imagine, if you let off the acceleration at high speeds, the car slows down slowly and the vibration goes away. So it's hard for me to say what the problem is.
When I switch over to the summer wheels and tires, I'm thinking of just changing them myself to see if the same vibration still occurs at the same speed and then deciding on whether to get them balanced or not.
A related issue, which I think some others have posted about on this site has been the wheel alignment. In the last 3 or 4 months, I've noticed that the car has a slight pull to the left under no steering input, so I may have to do an alignment soon.