Ford Excursion :: Hellwig Sway Bar Links Work With Oem Sway Bar?
Can the hellwig sway bar links will work with an oem sway bar? I need new ones and figured why replace with something I know will fail early...
View 3 RepliesFord Super Duty (1999-2016) :: Greaseable Sway Bar Bushings And End Links
I have a 2002 F350 4x4 CC 7.3 i am wanting to change the sway bar bushings front and rear to poly and I want greasable bushings to avoid the squeaking that you get with these bushings alot of the time. I would like to change the end links to poly too i realize these wont be greaseable. What was the outcome and where did you buy the bushings. What is the size of the front and rear sway bars and the length of the end links??
View 14 RepliesFord Super Duty (1999-2016) :: Sway / Stabilizer Bar Links Rattling?
I'm on my second set of links. The replacement were Dorman 3 years ago. They are rattling again. Do I just replace them again? I forgot to add, the bushings were replaced this year.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: 2003 - Running Rough / 2 Cylinders Not Working Correctly
I have a 2003 F250 7.3L. I put new injectors in my truck four months ago and all of a sudden, I have 2 cylinders not working correctly, making the truck to run really badly. I sent the 2 injectors from the bad cylinders back for warranty and they replaced both of the injectors but nothing was wrong. I put them in and the truck still runs badly. I have a new fuel filter, new ICP, new CPS and glow plug relay. I cannot drive the truck, it smokes white at idle. I can unplug each injector at a time and cyclinder 5 does not change how the truck runs
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Trans Not Locking In 1st Correctly
I bought this truck with 200000 miles and its been flawless, its now 900 short of 600000.. I use it to haul everyday.. nothing heavy mostly a car or truck and every once in a while a skid steer. I got 560000 out of my trans, i take it easy. lol
at 350k I installed a Jw valve body drilled pump, tripple disc converter and solenoid pack.. at 560k it went, i pulled it and brought to a guy i trust as much as you guys trust BDS.. Ive had what Ive called a vibration since day one, could be a shudder, could be a shimmy.. what ever.. I brought it back and he says nothing would do that from a trans, so I went through drive shaft, new t case ripped apart rear end and its still there and I have just been dealing with it.. about 2 months ago it started acting up in first. when I pull down to drive I get the normal bump and start to go, it feel like the truck slows, then another bump and it climbs normally with the shudder.
took it back and he said maybe a stuck valve in small VB, so I pulled it and went down there and it was fine, I reinstalled and still does same thing. I then put a pressure gauge on it and it swings as it should sits around 70 psi and will climb, only in first it will climb and fall back to 70 like a switch was flipped, and the rest of the gears bleed off slowly or normally.. He then said it could be the big valve body, so I swapped that one out with another and no real change, maybe its a bit more noticeable.
I am at a loss. Could this be loose feed bolts? Could the shudder that I can feel at most speeds be the 1 gear slipping a tiny bit all the time? I am told that first gear is always on.. this truck has been a dream until this trans issue..
Ford 7.3L Power Stroke (1999-2003) :: Can't Drive - Sway After Leveling Kit?
So I went from a 3 inch to a 2 inch leveling kit. After tightening everything up the sway bar was a hair off. I pulled it out of the garage and got it lined up. Fast foreward the next day and went on a 200 mile trip hauling an empty goosneck and noticed it one time. The day following the the truck has went into this horrible sway through the tires back and forth that makes it undrivable. Looking at tie rod ends the one at the pitman arm is shot. I order the whole front steering kit from xrf and I'm going to replace. I know I also have some play in the box but I have for awhile. So what else would there be to look at? I need to get this fixed. I will update after the steering is put back together.
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Thumping Noise That Generally Accompanies Worn Out Sway Bar Bushings
I have been having that nice thumping noise that generally accompanies worn out sway bar bushings. I did bushings last spring but a noise came back shortly thereafter. Finally got bothered enough/ found enough time to take a look at it and tracked it down to the sway bar again. My right front axle mount has taken damage before and is now all bent up, not allowing the bushing clamp to hold tight to the bushing. Pictures of the issue are below.
Front view of the entire mount.
Rear view showing the sway bar mount plate.
I am unsure what to do about this mount. As you can see it has been pretty messed up by the PO. What could be done to fix the issue?
Ford Excursion :: Sway Bar End Links / Loud Clunk
I've been having the loud clunk under the drivers side floor, that many others have as well. Did many hours of research and replaced the sway bar end links. Napa only had the left side in stock so I did it first last weekend and did the right side this weekend. One thing I noticed when doing the right side was the hole in the frame was all wallowed out. Drilled out the bushing in the upper end link and used a bigger bolt to fill the gap up. went for a drive and the clunk was way worse than it ever was still on the left side. So I took off the left one and went for a drive. Sure enough no clunk, the left one was wallowed out as well. So I did the same thing on that side and the evil clunk is finally gone. Just thought I would throw that out that if have a clunk after replacing the end links, Check the upper holes.
View 14 RepliesFord Excursion :: Clunking Noise - Front Sway Bar End Links
I plan on replacing as I have a clunk happening. Thought I'd try here first.
Is there a brand that's better? 1Aauto has OEM. Is there a brand that's better or makes a difference?
Or is a front sway bar end link a front sway bar end link?
Ford Excursion :: Correct Length Of Front Sway Bar End Links
What is the correct length of the front sway bar end links. I need that info to order replacements for my 04 X EB 6.0 4x4. I just don't want to wait another day.
View 3 RepliesFord Ranger / B-Series :: 1993 - Front Sway Bar End Links?
I'm new to the whole Ranger truck thing since buying a 1993 Ranger 4x4 for my 14 y/o son. It has a 4 inch suspension lift and a 3 inch body lift running 33x10.5x15 tires. The front sway bar is not hooked up. I know that i will need drop brackets for the sway bar but my question is about the end links needed for this truck. There are 2 tabs with provisions for a horizontal bolt on each side of the twin I-beam where the end link would attach and the sway bar has a single horizontal hole on each end. Searching for replacement links at various auto parts websites only seems to yield the standard end links that consist of a straight bolt with a nut on each end and the rubber insulators. That clearly is not the correct end link for my application. Not sure if the front suspension is the factory installed unit or if it was swapped some time in the part.
View 4 RepliesFord - Explorer :: 2000 - Front Sway Bar Links Coming Apart?
One is coming apart, so I'm gonna replace the pair. My Chilton book says to jack the front end up. The part instruction sheet makes no mention of doing that.
Raising the front would allow the control arms to hang. That would seem to me to make it harder to deal with the links.
Ford Excursion :: 2004 F350 - Front Sway Bar Links Keep Wearing Out After 3 - 4000 Miles?
My 04 6.0 Limited and both front and rear sway bars. The front links keep wearing out after 3-4000 miles. But, I saw someone in here put F350 Sway Bars in their Excursion? REALLY?? Is this right or is this snake oil? Is their another way to fix the front links so they don't wear out so quickly??
View 4 RepliesHonda - Cr-v :: 2005 - Loose Sway Bar Links
The Honda dealership told me my 2005 CRV has loose sway bar links. How are these fixed? They quoted a price of $290 for the front links and $374 for the rear links. Does this sound reasonable.
View 14 RepliesCamry :: 2005 - Change Front Sway Bar Links?
I want to change the front sway bar links on a 2005 Camry that has been driven in central New York (ice, salt, corrosion) for 10 years. There is definite wiggle and noise. I recently replaced the ball joints. That was difficult. How difficult is it to remove the sway bar links? Looks like a 5MM or so allen wrench is supposed to hold the ball joint type link to allow 18MM nut to be removed. A 5MM allen wrench is about 4 inches long and skinny. An 18MM wrench is about 12 inches long and beefy. I am skeptical about breaking the nut loose.
Will I need to heat the nut? If yes, how? With a simple propane torch? If yes, how does that work? Apply heat and wait for a sound that indicates the rust has broken? Apply heat for a time, try to hold with the allen wrench and try to undo the nut? Keep trying that again and again until it works? This would be after multiple rust busting spraying to make this easier. I used a 4 inch grinder to grind the nuts off the ball joints to remove them (I know how that sounds, but that is what I did). Thoughts about that for the sway bar links? I am a bolt turner who can stand some aggravation.
Prius (Gen 2) :: Front Sway Bar Links Making A Bad Noise
Both of my front sway bar links have a bad joint and are making a bad noise.. I purchased the replacements and tried to loosen the nuts with no success. I put some oil to loosen them and will let them set over night. Next attempt will include a breaker bar.
View 4 RepliesAlignment :: 2000 - Changing Rear Sway Bar End Links?
My car is a 2000 Corolla CE.
If I replace the rear sway bar end links, do I need to get an alignment? (I just got an alignment 2 days ago). Here is a DIY on replacing the rear sway bar end links: [URL]
The top attaches to the strut.....what is the bar the other end attaches to?
Sonata I45 (YF - 2011+) :: Rear Sway Bar And Links Installation
I just installed rear sway bar & links, this made a world of difference in the way the car handles as soon as I made the first turn I could feel the difference in the car it definitely corners flatter, the install only took about an hour did it in the driveway on ramps, I installed the kia sway bar 555102T000 the bar is 18.3 mm while the stock one is only 15mm I included some pics...
View 8 RepliesJetta - Volkswagen :: 2002 - Broken Sway Bar Links
My mechanic says I need to replace both front sway bar links on my 2002 Jetta....I am, of course, hesitant to do it at this price. How critical is it to replace? Can I get junk yard sway bars to make it cheaper? And can I do it myself (have no experience fixing anything....
View 11 Replies