Santa FE SM (2001-06) :: Code P0306 Came Up - Cylinder 6 Misfire
I have a 2004 Santa Fe with the 3.5. Today I started it and the check engine light came on. It was not on before this. (We had a lot of wind and rain from the storm but nothing major.) And seems to be running fine. I went to the auto parts store and they ran a diagnostic and the Code P0306 came up #6 cylinder misfire. They said probably Spark plug, wire or coil for #6, then went to look up code in computer and did not have my truck so they went with Kia or Domestic, which gave different possibilities for a code P0306.
They had me buy some fuel injector cleaner as injector was on the list. The light is still on so I guess the cleaner was not the magic bullet. I spoke to a lady at another auto parts store who is a wiz when it comes to cars and has been around them and fixing them a really long time. She says the Code P0306 is Spark Plug, wire, coil #6. She has a 4cyl Hyundai car not truck and she had the code for her #4 misfire in the past and she started her repair cheapest first, Plugs, wires her code was still there she then changed the coil and that did the trick for her.
I on the other hand can't do this stuff myself. Can't afford the dealer anymore or to have a shop do a tune up AND coil if I don't need all new plugs and wires just a coil as they will charge a lot to do a lot all. And it may not need it or even be any of those things. I also suspect the dealer and shops will want to still hook up their computers to do an costly diagnostic because the light is on, even though I know the parts store already came up with a code P0306 twice. Spoke to the dealer on the phone and he already basically said they would want to do that first for $100 plus the cost of repair.
I brought the truck new. It now has 91,500 miles on it and the dealer has already done two tuneups on it in that time, Plugs and wires. I hear it probably shouldn't have even needed these tuneups in this amount of millage? So the last one was probably about 2 years ago and a few thousand miles maybe a guess 10,000-20,000 miles ago. Do you think a plug and wire would be bad already in that few miles?
Ford F-150 - 1997-2003 :: Code P0306 - Cylinder 6 Misfire
So my 99 F-150, 4.2L started throwing a code a few weeks ago, P0306 #6 Cyl Misfire. This thing has got 238,000 and has been the most reliable commute vehicle I've owned.
Today I changed all the plugs and wires (they were due anyways) which didn't resolve the issue. After clearing the code, got about 3 miles out and it came back. Running SeaFoam through the system on this tank as well, but I'm leaning towards an EGR blockage like what is described here:
Sparky's Answers: 1999 Ford F150, P0306 Misfire Cylinder #6
I was about to buy a new coil pack but I'd rather not continue to throw parts at this, as I've read many others do with this same exact situation, only to end up with the same code. I've replaced the coil pack once already a few years ago when I lost a cylinder on the way to work.
Ford F-150 (2004-2008) :: Loss Of Power - Code P0306 / Misfire On Cylinder 6
Having 3 new codes coming up. P0306-misfire on cylinder 6, p0158, p2272. Use my truck as a daily driver for work. Driving along before 80km/h is not to bad but can still feel a little loss of power. If i step down on gas the truck has no power and sounds like maybe cat converter is plugged. If truck is pushed to limit she will make it to her 4000 rpm and will change her gears. So i'm just glad its not tranny.
View 3 RepliesBuick - Regal :: 1996 - CEL Code P0306 Cylinder 6 Misfire Plus P0102 Mass Airflow Sensor
Ok, my 1996 Buick Regal is acting up. I got a CEL, which was a P0306 (Cylinder #6 misfire), took the car to my shop, and they diagnosed as a faulty Ignition Control Module. Fast Forward, a day later, the car now has a hard start problem and throwing the same code, plus a P0102 Mass Airflow Sensor.
So my questions are:
1) Could a faulty ICM cause a single cylinder misfire, did they just replaced a random part? I would think a bad ICM would a multiple misfire considering on this car each coil controls 2 cylinders.
2) Are the two codes related? ie fix one, and the other would go away? or are they separate issues?
3) What could be wrong with my car?
This mechanic has been in my family for years, however, I'm not very pleased that a day later, my car seems to have more problems than before. Am I being too harsh?
GTI 337/20th Anniversary :: Cylinder Misfire Codes For OBDII?
I changed my sparkplugs and coil packs last month. Was getting CEL light but it would go away after a while. I figured out that I had gapped my spark plugs way to small (almost touching) so I took them out two nights ago and regapped/ reseated them.
My car was running fine yesterday, but today when I started my car up, the engine was shaking a lot for about 10 seconds and the CEL was blinking. After 10 seconds the shaking and CEL went away...
It drove fine. I'm just wondering what could be throwing these CEL's and causing the shaking? Plugs are gapped to 0.32
Also, I had my timing belt and water pump replaced almost two weeks ago now. Any chance that could be lending to the problem?
My guess is that one or more cylinders are screwy. I'd rather not bring it into the vw mechanic since I'm tight on cash.
Oldsmobile - Alero :: 2003 - P0306 Misfire Code - Engine Knocking?
My mom's 2003 Alero has had a bad catalytic converter for the last few years.. at least that's what she was told when she took it to the shop. The engine light (P0420 threshold below efficiency) has been on over the last few years and I occasionally check it with a code reader to make sure no other codes have been added. Up until today - as far as I know - none have been. Now today when she was driving it the engine light started flashing and running rough and making a knocking sound.She brought it straight home and I hooked my scan tool up and it gave the same cat code as I just mentioned, plus a P0306 misfire code. So I pulled the plug wire on number six cylinder and hooked up a spark tester to it - and it showed a decent spark. And to verify the spark being normal, I tested at another plug wire and the spark looked about the same..so I don't think anything is wrong with number 6 plug wire or coil or anything like that but am not sure. Also, the spark plugs were replaced a couple of weeks ago because the ones in the car were worn down about .010''. I can't imagine this having anything to do with the misfire because I did them myself and made sure they were gaped properly and that all the wires were put back on the correct plug/cylinder and plus it ran fine after the plugs were installed - but thought I would mention it anyways. And I was very careful not to damage the platinum on the plug when gaping them.
Did a little bit of research and found this: A code P0306 may mean that one or more of the following has happened: Faulty spark plug or wire Faulty coil (pack) Faulty oxygen sensor(s) Faulty fuel injector Burned exhaust valve Faulty catalytic converter(s) Running out of fuel Poor compression Defective computer
Ford Escape / Hybrid :: 2002 - Misfire - Getting Code P0305 And P0306?
I have a very Big problem with my Ford Escape 2002 I have this problems code: P0305 accuses Cylinder #5 P0306 accuses Cylinder #6.
I already change the gasket i buy the felpro Kit, and i Also replace all the sparks and spark plug boots, I clean the air sensors and i also replace the EGR, i try to switch cables, and all is the same the car start buy when i accelerate it just go off, i don't know what can i do next, somebody told me to change the fuel injector, i take the pressure in both spark holes the number 4 was 150 and the 5 and 6 was 120, No leaks oil. My car is a Ford Escape 2002, XLT 3.0 4x4
Ford Ranger / B-Series :: 1999 - Code P0305 Cylinder 5 Misfire
I have a 1999 ford ranger 3.0 6 cyl with 211,110 miles It started running rough without any previous warning signs. In idle its barely noticeable, once i put it in gear it gets rougher and when driving around 40 to 45 mph it roughly shakes and shimmies. Once I get past the 40 to 45 mph range it settles back down. Is there a specific issue that would cause that at that speed. When going up over a bridge the check engine light blinks.
I changed the spark plugs and new wires and it offered no success even though one of the plugs were black (to much gas). I have borrowed a diagnostic tool and got P0305 cylinder 5 misfire, I am thinking fuel injector to replace, what else should I be looking at?
Ford Ranger / B-Series :: 1999 - 304 Code / Misfire In Cylinder Number 4
1999 ranger 155k 3.0 flex fuel. 304 is misfire in cyl number 4... I replaced the plugs and wires and checked the coil. the compression in cyl 2, 4, 5, 6 and got 80-90 psi so they are consistent but consistently bad right, it may be my compression tester.
The #4 plug was spotless after running 5 min, the #5 plug had some black on it already. Its hard to tell but it seems I had fuel residue on the plugs on cyl 5 and 6 but none on 4? Whats next pulling the intake to get to the injector?
Ford - Explorer :: 1999 - P0303 / Cylinder 3 Misfire - Resetting Code
On my wife's '99 Explorer, she just acquired, we had a P0303, #3 cylinder misfire. I found the plug cracked and replaced it. Do the codes reset themselves or do I have to do it? I'd rather not disconnect the battery and reprogram the radio.
View 7 RepliesPassat (B5) :: 1999 1.8 Turbo Automatic AEB Engine - Cylinder 1 Misfire Code P0301
I have a 99 Volkswagen Passat 1.8 Turbo Automatic AEB engine. I recently did a rebuild on it and ever since I keep getting this code P0301 that says "cylinder 1 misfire". The engine is also running rich and the spark plug in cylinder 1 keeps getting gummed up. I've changed the coil and the spark plugs and the injectors and it works temporarily but then the problem keeps reoccurring.
View 7 RepliesSubaru - Legacy :: 1999 - Cylinder 2 Misfire Code As Well As Random Power Loss
I had plugs and wires changed to try clear code. Car seemed to do some better but while trying to go up a steep hill car started stuttering and jerking. Power went out of car and check engine light started blinking fast.after let the car sit for bout 45mins car started running fine again and light stopped flashing but remained on. Code read cylinder2 misfire again.
View 10 RepliesFord Super Duty (1999-2016) :: 2003 - Cylinder 3 Misfire With No Code?
my 03 f250 has a 5.4 and i cant seem to get rid of a misfire in cylinder 3. i had a p0353 code but that no longer shows up. i replaced all the coils with Accel coils, replaced the plugs with motorcraft platinum. i have checked the wire all the way back to the PCM and it checks out. i replaced the pcm with one that has been reprogrammed. i have swapped the injector and coil with another position and still get misfire at #3. Replaced the coil connector with a new one. I have good fuel pressure. I no longer get the code but the misfire is still there, unplug the coil and injector while running and no change. Unplug a different cylinder and you can tell the change. I checked compression and its good. I am lost here!!!!
View 14 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Code For Cylinder 3 Misfire
My 5.4 F250 with 200,000 miles having many problems... It all started a few months ago, when the cam needed to be replaced, and a cam phaser was also replaced at the same time. It ran fine after, then threw a code for cylinder 3 misfire. The guy I took it to said it was due to the huge crack in the exhaust manifold and that was messing with the o2 sensor coming up as a cylinder 3 misfire. So, got the new manifold and it was good for a few weeks.
Now, starting the other night, Friday the 13th, it threw a CEL when I was coming into the driveway. It had been throwing a code every once in a while, and I brought it to school to scan it Friday the 13th but there was no code. So, I assume that it is an intermittent problem, no big deal. When I go to get in my truck to go to work a few hours later, the 5.4 cranks... and cranks... and cranks.
I get it to fire up, and it dies again. Run codes, and it says that the cam positioning sensor is broken. Replace both of them, still acts up ie. doesn't start when it does start it runs very rough and stalls. Get it up to my uncles shop, and replace fuel filter.. Still runs like trash. Run codes now, and it says rich/lean in bank 1.. My uncle tells me to move my truck out of the shop, so I start it up, and it runs great. No hiccups, it idles perfect as I move his truck out of the shop first.
I park my truck outside and let it idle for about 10 mins, and when I come back out it is still idling, perfectly fine. I get in, put it in reverse, and get about 20 feet when it dies and will no longer start back up. What could be going wrong?! Sick of throwing money into this thing! At one time while started up in my uncles shop, it was blowing black smoke, as if it was a diesel!
Ford 7.3L Power Stroke (1999-2003) :: P0308 Fault Code / Misfire Detected On Cylinder 8
New to diesel trucks and wondered if this recurring code is a serious problem. I clear DTC and truck will run fine. Might stay off for 2 days or 2 months and same code comes back. Truck seems to run just fine even with service light on.
View 5 RepliesFord Super Duty (1999-2016) :: 2003 5.4 F250 Head Gasket / Misfire Code On Cylinder 4?
After replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 RepliesPassat (B5) :: Car Has Misfire And Code On The Cylinder
I am having a misfire code on the #1 cylinder. Its not bad but I really want to nip it in the butt before it goes out completely. I was told to try and get some of the older style coilpacks that bolt on and go with them. Can I put them on my 03 passat 1.8t.
View 2 RepliesNissan :: 1989 - Cylinder Misfire CEL Code
1989 Nissan pathfinder. 6cylinder - VG30i - Manual trans - Throttle body injected. No CEL.
I've been trying to diagnose a misfire on my 89 Pathfinder during my lunch breaks. I just changed out the the plugs, dist. cap, dist. rotor and wires. Still misfiring.
When it starts-up the misfire "putt" is random, but once the idle lowers to about 1k it gets very rhythmic and just sounds like part of the idle and the car vibrates a little too much. Stinky exhaust (obviously) but no blue smoke or anything.
Finally bringing the car home to do some diagnosis over the weekend. Next I'm going to do some cylinder compression checks and vacuum checks. Probably check fuel pressure too. Is it odd that I'm not getting a cylinder misfire CEL code? The manual lists the code type.
Silverado :: 2000 - Code Saying Misfire On Cylinder 8
So I have A 2000 Chevy and i keep getting a code saying i have a misfire on cylinder 8. i have replaced the spark plug, i have replaced the coil. this code is still showing up. what else could this be?
View 2 Replies