Ford F-150 (2004-2008) :: Rough Idle Almost Like A Misfire
I hopped in my truck this morning, fired it up, and it idled nicely. I drove around the corner, and noticed that the truck was barely responding to the throttle. Then things got shaky. It was a very rough idle, almost like a misfire. But I managed to get the gas to respond and got the revs up to about 3K and it seemed to run smooth.
No CEL either. Currently, I have no place to really look at my truck as I don't have a garage, or driveway for that matter. I don't have a scanner that can read live data either. I'm limited in my tools currently as well.
Prius (2004-09) :: Misfire On Cylinder 2 And 4 - Car Severely Idle Rough
I own a 2007 prius, it has about 320,000 miles. It has recently been diagnosed with a #2 and #4 cylinder misfire. The car severely idles rough, but when getting in the gas it goes away. I have replaced the spark plugs, the old plugs were very white(lean), replaced fuel injectors, used fuel injector cleaner. I've sprayed carb cleaner around the intake to see if I might a leak--no leak. The motor uses about a quart of oil every 1,000 miles since about 100,000 miles. I'm just guessing, could it simply be low compression causing this? I pulled the new spark plugs after about 5,000 miles and they where white also.
View 9 RepliesPassat (B5) :: 2004 - Random Misfire At Idle Like One Hard Knock
2004 Passat 1.8t 4motion ... I am getting random misfire at idle like one hard knock then every thing is ok. I also have no MIL light or retrievable codes. I checked for vacuum leaks don't see any. Change out some old vacuum check valves. Replaced oil breather hose had crack. I Changed timing sensor, timing belt and fuel filter fuel pump died changed out. The old fuel filter had something rattling around in it is that normal? Also when I get gas no matter where, 91 octane only the car idle stumbles about 5 minutes after fill up then smooths out after a mile or so. EVAP purge valve clicks some times? Haven't check EVAP canister for saturation. Fuel regulator? I haven't checked fuel pressure. Car was not starting after sitting for week end hard start took 3 to 4 tries then starts up ok for some reason that is not happening now?
View 6 RepliesFord F-150 (2004-2008) :: Rough Idle Cylinder 3 Misfire
2004 Ford F150 5.4 Triton 3V Vin5.....
How this started, Drove through a lot of water as our City was in a flood on my way home and and the truck started running rough and got worse over time, I can now barely get to 40 mph as it starts to ping and sputter with no power.. the truck has been parked and not driven while in the shape it's in.
The truck keeps giving me error code P0303 Cylinder 3 misfire detected, P0174 System too lean (Bank 2) and at times another error P0300 saying multiple cylinder misfires detected.
After clearing the codes, I got new codes stating Misfire on Cylinder 2, 3, 4, 6. System too rich (Bank 1) System too lean (Bank 2)
Cleared the codes again and I'm back to Cylinder 3 misfire and System too lean (Bank 2)
What I have done so far... All repairs with in a few days...
1. Changed all spark plugs.
2. Changed all Coil Packs.
3. Changed number 3 fuel Injector.
4. Changed the Oil and Filter. (no water in the oil)
5. Changed the MAP Sensor.
6. Changed Bank 2 O2 Sensor 1 and 2.
7. Loosen the Catalytic Converter on the drivers side to re-leave back pressure thinking the Cat was plugged, still loss of power. I also drilled a small hole in the exhaust at my lowest point to see if it had water in it and it does not.
Checked for vacuum leaks using starting fluid around the intake manifold, no change in idle.. I also checked to make sure the vacuum line was still connected on the back of the intake manifold, I have found nothing leaking.
I also had cleaned the throttle body and changed the throttle position sensor.
Repairs within the last 6 months or less...
8. Replace passenger side cat.
9. Replaced both Bank 1 OS Sensors
9. Replaced Timing chains, Gears, Guides, Guide Tensioners, Oil Pump and pickup tube, Water Pump.
Cam Phasers are fine.
And number 3 coil is getting spark I changed the Ignition Coil again thinking maybe another bad pack.
Still #3 misfire and System too lean (Bank 2).
I am at a loss and not sure what to try, except for a compression test on cylinder 3 but I honestly don't think it's compression or a burnt valve.
Ford F-150 (2004-2008) :: Misfire And Rough Idle - EVAP Sensor
My 2004/ 4.6L F-150 had misfire issues and rough idle. Since changing the plugs and a COP the idle is better. It seems to stutter a bit at low RPMs around town, but it fine at higher RPMs. What to check next. Also since fixing the misfire and clearing the codes from the computer it won't enable all the emissions monitors. I've drive over 100 miles and the EVAP monitor still isn't on. The truck has about 213K miles on it.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2004 - After Warm Up Misfire When Idle?
I have an 04 F-250 6.0l Power stroke diesel with a problem. The engine starts fine and runs normally until it gets warmed up. Once it is at the normal operating temperature it starts to sound like it is misfiring when idle. Once I accelerate it sounds normal again but when I slow to idle the misfire comes back.
View 5 RepliesFord F-150 (2004-2008) :: Misfire / Rough Idle Under A Bit Of Load (acceleration) And Uphill
2005 Ford F150 lariat 5.4
I had a misfire under a bit of a load (acceleration) and up hills. I changed spark plus with OEM Motor craft ones, truck ran super nice for a couple week.
Had the engine light flash, slow down and the RPM go up a tiny bit then back down and the light goes off
Now I'm back to miss fire different location, and a rough idle. I've swapped coil packs around and the miss fire stayed on cylinder 4.
Spark plug screwed or injector or ?????
Ford Escape / Hybrid :: 2004 - Intermittent Rough / Low Idle / Misfire On Startup
My g/f's 2004 Ford Escape (3.0L V6 AWD 112,000mi) is acting up. After a full day of sitting, with the second half of it raining steadily, she was driving her Escape and it was acting funny (miss-firing, she said). The engine light came on and soon began blinking. She got to my house shortly after it started this. We left it and I drove for the day. Later that night, I drove it and it seemed fine. The engine light was on, but not flashing anymore.
The next day I took it my friend that was a Saturn mechanic and now working at a KIA dealership (same owner as the former Saturn and current Buick/GMC and Chevy Dealer). It ran fine for me. So he tries to scan it, his Mac Tools scanner won't read it. The KIA scanner wouldn't read it. I drove it the Ford dealer up the road. They said they couldn't get to it until after lunch, I just want the codes read. They re-iterated, and I told them to pound salt and went to an independent shop where I know a guy. They read it right away for me. "Mis-fire on start-up" & "Cylinder 4 Mis-fire." were the two codes stored. He cleared them.
She got the tune up basics (plugs, wires, air filter, etc) and did the complete tune-up herself yesterday. (I was impressed). She put 94 in the tank and some fuel system cleaner in it as well. She said there's been no change and today I finally saw what it was doing. Sometimes during idling at a stop light, the RPMs will drop to almost zero, the lights dim but so far it has not stalled. It'll do this for several seconds, then correct itself and idle normally.
Currently, the engine light has not come back on. She's thinking coil pack (each cylinder has a coil on these engines) on #4. She wants to switch it out with #1 and see if the problem follows. I think that might uncover the cause, or it could be the battery. It's the original, never been replaced and has a lot of miles on it, but it survived this past winter, without trouble. In my experience, most batteries crap out due to age in the fall when the cold snaps start.
Ford - Mountaineer :: 2004 - Buck / Shake And Idle Around 400 RPMs - Misfire On 3 Cylinders
I recently picked up a 2004 Mercury Mountaineer, 4.0 with 113,000 miles. OBD reader says misfire on 3 cylinders.. Installed new plug wires first.. nothing.. going to install plugs next when she is cold. Now, am I really looking at replacing the coil pack to end the misfire codes? She likes to buck and shake and idle around 400 rpms.. I know that is too low..
View 4 RepliesFord F-150 (2004-2008) :: 2007 - Engine Misfire At Idle And On A Downgrade While Driving
Im trying to chase down an engine miss fire on a 2007 with the 5.4L. It only seems to miss under no-load conditions, such as at idle and on a downgrade while driving. Acceleration and under a load it runs fine. New Champion plugs were installed at 135,000 miles. The truck now has 150,000 miles and has only been miss firing for the last 1,000 miles or so. I pulled the connector off of the coils one at a time to try and figure out which cylinder/s were missing. I thought I found the problem ones and replaced two of the coils, but it ended up not fixing the issue. Ive tried spraying carb cleaner at and around the intake to check for leaks, but found none. I have a scanner, but the check engine light is not on, so its not much luck.
View 5 RepliesFord F-150 (2004-2008) :: Rough Idle / P0012 - Misfire Codes Associated With Bank 1 And Cylinder 3
5.4 3v. my last few weeks have not made me a fan. Here are the details:
I bought a 2008 F150 XL 5.4 3v with a cam phaser knock. Have done other timing jobs in past with no trouble so I was not too afraid to tackle this one. famous last words...opened the motor (shout out to the passenger side valve cover and its designer here) and found semi damaged roller follower on driver side. Worn cam lobe on the corresponding lobe and a loose chain on passenger side. proceeded to :
Change all timing components: phasers, chains, tensioners crank sprocket, all applicable bolts and BOTH cams as well as all lash adjusters and roller followers. most looked fine in fact all really did with a bit of wear on a few roller followers but only one bad one. engine didn't look to bad pretty clean.
Double and triple checked my timing chains and it was spot on. dark link on spot on crank, two dark links on the L and R dead on. put it back together. oh yes, changed all plugs with motorcraft ones, didn't even break one. did not change vct solenoids because I falsely assumed I could change the later easily if needed. they looked ok. screens intact etc... silly me for not realizing how kind Ford was in 2007 and later to necessitate removal of valve cover. I was reading a previous one on the how tos and assumed later models would be the same since it was the same sensor...
Cranked truck ran great. I mean perfect. sounded perfect. ran like a scalded cat. till it got to hot idle then it started doing its thing. rattle shake till you revved it. ran fine just wouldn't hot idle fine especially in reverse or under slight load. replaced driver side vct since ford only had one and I started on the easy side ordered the other one waiting for it. seemed to improve dramatically meanwhile I am driving this truck to test it. I drove it to work 50 miles each way and it ran great.
After a few trips it popped the P0420 light, seemed to run ok, cleared it watched it wouldn't come back. O2 sensor did seem to imply a bad cat on bank 1 since it seemed sensor two was mimicking sensor one and not staying stead like the other bank. still ran fine,
So I decided to check back pressure on the cat. I pulled sensor one out of bank one (really a joyously tight squeeze in there) hooked up my gauge and got 0 back pressure. revved it and all nothing. hooked sensor back up pulled truck out of shop and it commenced to running like crap. I mean bad. running worse than before I got it. Popping P0012 code continuously, and tons of misfire codes associated with bank 1 ..cyl 3 etc.. I tried swapping coils, pulled coils and checked spark with a tester and firing away looks like tons of good spark.
Now the weird part is : looks like bank one is dead. I can unhook any coil pack and/or injector and it runs the same and sounds like it is missing. if I unhook one off of bank 2 it almost dies or does. so bank 2 seems to be running fine. it will start and run but sounds like it missing sets flashing check engine light and backfires and stalls like crazy. I even second guessed my pressure gauge and unhooked exhaust manifold from pipe and it sounds even prettier when it backfires out of there but no change. I pulled cam sensors and cleaned it again and even tried swapping them since they looked identical but no change so I put them back.
Now I can only surmise that I am out of time somehow? or I have a gremlin perhaps? I like working on cars (usually) but this one is getting old. how do I verify what is wrong. if it is timing related how do I verify that now definitively once my marks moved I really cant figure out how to tell if it is in time? Since it has all new parts and they all ran beautifully till now. could it possibly be the vct solenoid doing all this? I plan on changing it when it comes in but surely it cant cause this many problems.. I unhooked it no change, and it does it at a cold idle and any rpm. really runs worse at idle but bad at any rpm.
Ford F-150 (2004-2008) :: 2006 - No Power / Rough Idle / Random Misfire Code
Have an 06 F150 5.4 3v with no power. spark knock. rough idle. wants to die while driving, and random misfire code. Have replaced fuel pump, filter, coils and plugs. What to check next? Already thought of EGR - it doesn't have one.
View 4 RepliesTouareg :: 2004 Misfires - Rough Idle And Hesitating / Shaking Under Acceleration
It's a 2004 V8 Touareg with 100k miles.
Getting horrible misfires and they're jumping around to different cylinders + other intermittent codes. The symptoms are ROUGH idle, and hesitating/shaking under acceleration.
The MIL has never come on in this car. But, it illuminates when you turn the key forward. (Almost like previous owner coded the light out?)
Replaced all 8 spark plugs, just ordered 8 new ignition coils. Hoping the misfires are the coil packs but obviously theres some other stuff going on here.
Pulled codes 2 weeks ago:
1) random/multiple misfire (P0300)
2) misfire cylinder 4 (P0304)
3) misfire cylinder 8 (P0308 )
4) warm up catalyst efficiency below threshold bank 2 (P0431)
5) secondary air injection system insufficient flow bank 1 (P0491)
6) secondary air injection system insufficient flow bank 2 (P0492)
7) 02 Sensor Circuit Slow Response Bank 2 Sensor 1 (P0153)
Pulled codes 1 week ago:
1) random/multiple misfire (P0300)
2) misfire cylinder 2 (P0302)
3) misfire cylinder 3 (P0303)
4) 02 Sensor Circuit Slow Response Bank 2 Sensor 1 (P0153)
Pulled codes tonight:
1) random/multiple misfire (P0300)
2) misfire cylinder 2 (P0302)
3) misfire cylinder 3 (P0303)
4) misfire cylinder 4 (P0304)
Cleared codes. Swapped ignition coils from 2 & 3 with 7 & 8. Drove around the block, then re-ran them:
1) random/multiple misfire (P0300)
2) misfire cylinder 4 (P0304)
3) misfire cylinder 5 (P0305)
4) misfire cylinder 6 (P0206)
5) misfire cylinder 7 (P0307)
6) misfire cylinder 8 (P0308 )
Touareg :: 2004 V6 138K Miles - Rough Idle In Neutral And In Drive When Stopped
Recently noticed the idle seems rough in Neutral and in Drive when stopped. When the roughness is subtle, that RPM gauge doesn't move and at other times with more pronounced surges the RPM gauge bounces around. Not sure if it is related but we just got back from a couples days in Tahoe. Tried reconnecting the gas cap with no change.
View 6 RepliesTouareg :: Misfire At Low RPM And Will Not Run
My Tourage has been at the dealers for three days. They said water in gas. They cleaned tank, filter, and pump and new gas. Still have the same problem. They replaced the coil pack all 6 and still same problem it misfires at low RPM and will not run. Dealer is getting sick of me and that they cannot find the problem. I have missed three days of work sine it broke down while I was visting family in VA. I am 425 miles from home with no way back. I have paid over $850.00 for work so far. The T. has 34,000 miles I fill I am going to pay allot more before or if they ever fix it. I have had some problems with my 05 V6 Tourage but for the most part been happy with it.
View 22 RepliesTouareg :: 2001 - Getting Consistent P0305 And P0307 Misfire Codes?
I'm getting consistent P0305 and P0307 misfire codes when my 4.2L engine is revved past 5,000 RPM. Have a done a bunch of diagnostics including a new timing belt to no avail.
Specifics:
I have 2001 Audi A6 with a 4.2L 40V engine (yes, I know it isn't a Touareg but the motor is the same!). Timing belt replaced about 1.5 years ago and it runs great. However, I'm getting some codes. 1) At high RPM (over 5,000 rpm) under load, I consistently get a P0300, P0305 and a P0307. Happens like clockwork. As soon as I hit 5,000 rpm, those three codes post. 2) After driving around for a bit, I get a P0340 (Cam position Sensor). Things I have done, all with no change: 1) Checked for Vacuum Leaks 2) Replaced all the spark plugs 3) Moved all the coil packs from one side to the other 4) Replaced the Cam position Sensors 5) Moved all the injectors from one side to the other 6) Inspected (as best I could) the variable cam timing system under the valve covers. Brown chain guides looked OK.
Finally, I changed the timing belt to no avail. When I disassembled, I found the motor was perfectly in time. My marks from the first change ~18 months ago were still in place and everything lined up. I was able to install the crankshaft lock and cam locking bar with the timing belt in place (it wasn't even off a fraction, the locking bar slid right in). I installed a new belt and all the rollers + tensioner. Didn't put in a new water pump but changed all the other pieces. The new install went great and I was able to get almost exactly the 5mm gap on the tensioner after spinning the motor a few times that Bentley talks about. Put it back together and took it for a spin. DARN!@ The same codes post at exactly 5,000 RPM: P0300, P0305, P0307.
Passat (B5) :: Rough Idle At 800 RPM With Misfire
I got an 800rpm rough idle, no serious lack of power, every time after filling up w/ gas she starts slowly (bout 3 secs) and then tries to die. she catches herself and revs from 400-1200 for about a minute, then drives away fine. Getting:
17544 - P1136 Bank 1 : System too lean
16825 - P0441 Evap ECS : Incorrect flow
16684 - Random/Multiple cyl misfire detected (intermittent)
16688 - Cylinder 4 : Misfire detected (intermittent)
Also have: 01039 - Coolant temp sensor(g2) : open or short to plus? (intermittent)
Doubt the last has anything to do with BIG problem, but my temp sensor on ly gets off 0 when i am moving and using A/C...is this going to cause issue now/later/ever?
Sonata NF (2006-10) :: Idle Seems To Almost Misfire When AC Is On
When at idle and it seems to either only do it or is worst when the ac is on. the idle seems to almost misfire. Usually its only for a couple seconds less then a min. I have had my odb2 hooked up to it and its about a 25-50rpm drop but it keeps doing over the course of a few seconds. It hasn't stalled doing it yet and its done it for years! however today at the drive thru it was quite aggressive. Usually I give it gas and its not as bad or completely stops, sometimes is doesn't work at all. This time I just let it keep doing it hoping a CEL would come due to it being more aggressive then ever but it just evened its self out after about 30 seconds. Almost feels like there is a mild performance cam in the car....
View 9 RepliesKia - Rio :: 2011 - Misfire At Idle And Low Speed?
My 2011 Kia Rio5 is misfiring bad, especially at idle and low speeds. I took it in to a non-dealer mechanic (since I'm no longer under warranty) and no codes came up. They said coil #3 was arcing, so they went ahead and replaced it and the spark plug. When I drove it home the car was misfiring more than ever. It misfired a couple years ago and I had a coil replaced (#3?) and a couple months after that it did it again. I could took it to another dealer (both happened while under warranty) and they said the reason the coil went out before was because the spark plugs were bad and hadn't been changed. So they replaced the #3 coil and spark plugs and it was fine until recently. I'm scheduled to take it to a kia dealer service dept. on friday, does this still seem like a coil issue? If not, what could it be?
View 1 Replies