Ford F-150 (2004-2008) :: 2006 - Random Misfire Code P0316
Friend has a 2006 with the 4.6 motor. From time to time he gets a random misfire code ( I think its 0316).. He claims it will only do it when the gas tank is less that half full. I don't see any correlation between fuel level and the code. I am going to check fuel trim values, etc, when the code is set, this weekend.... all I can assume is low fuel pressure which sets the code... Any problem with the pressure module or fuel pump / discharge hose that is related to low level in the tank ?
View 3 RepliesTrailBlazer :: Random Misfire And Code P0300 - Rough Idle
'02 TB w/ code P0300 / Random misfire. Started the other day when it was very damp out, FWIW. Feels like ur driving on rumble strips during acceleration. Rough idle also. It does not do this continually though as after a while (minute) it clears up and runs smooth for a while then runs rough & light will again for a while. I seafoamed it today since it been about 60k since last seafoam. I thought that might have worked until I drove about 20 mile and it went rough again. I also cleaned the oil out of the cam sensor elect connector, since that caused rough running before, although it didn't throw that code. It seems to be very intermittent. '02 TB, 185k miles, orig plugs changed at 125k. Is it actually just going in & out of a limp-mode? O2 since it's random ???
View 14 RepliesFord F-150 (2004-2008) :: 2006 - Cylinder Misfire And Random Miss On Startup
We've got a 2006 F150 with a 5.4 in it. One of the new kids was told to change the spark plugs, then when I went to start the truck the next day it was missing bad. Plugged in the Ford IDS, number 7 cylinder is dead. Only codes are for that cylinder misfire, and random miss on startup. So, I double checked the kids work and it was all fine. Tried putting a new plug in, didn't work. Moved the coil to a different cylinder to see if the miss would jump, stayed on number 7.
Used a noid light to verify COP harness was working, and it was. Put a new coil on it anyway since I had one, still missing. Used noid light to verify signal going to injector for the cylinder. Signal was good, replaced the injector for the cylinder. Still misfiring. Ran a compression test and the cylinder has good compression. The threads for the plug are fine, not cross threaded or torn out. The only thing I can think is that the PCM has gone bad in a way that its firing the injector/COP, but doing so at the wrong time some how.
Every other cylinder is running fine, O2 sensors fine. PCM isn't trimming anything back to account for anything, and if it was it would do it to multiple cylinders to keep the engine balanced. Cant think of any more tests, and I don't believe there is anyway that the airflow could be restricted to only 1 cylinder, but I could be wrong. Wanna try and solve this to keep from sending it to the dealer.
Ford F-150 (2004-2008) :: Rough Idle Almost Like A Misfire
I hopped in my truck this morning, fired it up, and it idled nicely. I drove around the corner, and noticed that the truck was barely responding to the throttle. Then things got shaky. It was a very rough idle, almost like a misfire. But I managed to get the gas to respond and got the revs up to about 3K and it seemed to run smooth.
No CEL either. Currently, I have no place to really look at my truck as I don't have a garage, or driveway for that matter. I don't have a scanner that can read live data either. I'm limited in my tools currently as well.
Ford F-150 (2004-2008) :: Rough Idle Cylinder 3 Misfire
2004 Ford F150 5.4 Triton 3V Vin5.....
How this started, Drove through a lot of water as our City was in a flood on my way home and and the truck started running rough and got worse over time, I can now barely get to 40 mph as it starts to ping and sputter with no power.. the truck has been parked and not driven while in the shape it's in.
The truck keeps giving me error code P0303 Cylinder 3 misfire detected, P0174 System too lean (Bank 2) and at times another error P0300 saying multiple cylinder misfires detected.
After clearing the codes, I got new codes stating Misfire on Cylinder 2, 3, 4, 6. System too rich (Bank 1) System too lean (Bank 2)
Cleared the codes again and I'm back to Cylinder 3 misfire and System too lean (Bank 2)
What I have done so far... All repairs with in a few days...
1. Changed all spark plugs.
2. Changed all Coil Packs.
3. Changed number 3 fuel Injector.
4. Changed the Oil and Filter. (no water in the oil)
5. Changed the MAP Sensor.
6. Changed Bank 2 O2 Sensor 1 and 2.
7. Loosen the Catalytic Converter on the drivers side to re-leave back pressure thinking the Cat was plugged, still loss of power. I also drilled a small hole in the exhaust at my lowest point to see if it had water in it and it does not.
Checked for vacuum leaks using starting fluid around the intake manifold, no change in idle.. I also checked to make sure the vacuum line was still connected on the back of the intake manifold, I have found nothing leaking.
I also had cleaned the throttle body and changed the throttle position sensor.
Repairs within the last 6 months or less...
8. Replace passenger side cat.
9. Replaced both Bank 1 OS Sensors
9. Replaced Timing chains, Gears, Guides, Guide Tensioners, Oil Pump and pickup tube, Water Pump.
Cam Phasers are fine.
And number 3 coil is getting spark I changed the Ignition Coil again thinking maybe another bad pack.
Still #3 misfire and System too lean (Bank 2).
I am at a loss and not sure what to try, except for a compression test on cylinder 3 but I honestly don't think it's compression or a burnt valve.
Ford F-150 (2004-2008) :: Misfire And Rough Idle - EVAP Sensor
My 2004/ 4.6L F-150 had misfire issues and rough idle. Since changing the plugs and a COP the idle is better. It seems to stutter a bit at low RPMs around town, but it fine at higher RPMs. What to check next. Also since fixing the misfire and clearing the codes from the computer it won't enable all the emissions monitors. I've drive over 100 miles and the EVAP monitor still isn't on. The truck has about 213K miles on it.
View 3 RepliesFord F-150 (2004-2008) :: Misfire / Rough Idle Under A Bit Of Load (acceleration) And Uphill
2005 Ford F150 lariat 5.4
I had a misfire under a bit of a load (acceleration) and up hills. I changed spark plus with OEM Motor craft ones, truck ran super nice for a couple week.
Had the engine light flash, slow down and the RPM go up a tiny bit then back down and the light goes off
Now I'm back to miss fire different location, and a rough idle. I've swapped coil packs around and the miss fire stayed on cylinder 4.
Spark plug screwed or injector or ?????
Ford F-150 (2004-2008) :: Rough Idle / P0012 - Misfire Codes Associated With Bank 1 And Cylinder 3
5.4 3v. my last few weeks have not made me a fan. Here are the details:
I bought a 2008 F150 XL 5.4 3v with a cam phaser knock. Have done other timing jobs in past with no trouble so I was not too afraid to tackle this one. famous last words...opened the motor (shout out to the passenger side valve cover and its designer here) and found semi damaged roller follower on driver side. Worn cam lobe on the corresponding lobe and a loose chain on passenger side. proceeded to :
Change all timing components: phasers, chains, tensioners crank sprocket, all applicable bolts and BOTH cams as well as all lash adjusters and roller followers. most looked fine in fact all really did with a bit of wear on a few roller followers but only one bad one. engine didn't look to bad pretty clean.
Double and triple checked my timing chains and it was spot on. dark link on spot on crank, two dark links on the L and R dead on. put it back together. oh yes, changed all plugs with motorcraft ones, didn't even break one. did not change vct solenoids because I falsely assumed I could change the later easily if needed. they looked ok. screens intact etc... silly me for not realizing how kind Ford was in 2007 and later to necessitate removal of valve cover. I was reading a previous one on the how tos and assumed later models would be the same since it was the same sensor...
Cranked truck ran great. I mean perfect. sounded perfect. ran like a scalded cat. till it got to hot idle then it started doing its thing. rattle shake till you revved it. ran fine just wouldn't hot idle fine especially in reverse or under slight load. replaced driver side vct since ford only had one and I started on the easy side ordered the other one waiting for it. seemed to improve dramatically meanwhile I am driving this truck to test it. I drove it to work 50 miles each way and it ran great.
After a few trips it popped the P0420 light, seemed to run ok, cleared it watched it wouldn't come back. O2 sensor did seem to imply a bad cat on bank 1 since it seemed sensor two was mimicking sensor one and not staying stead like the other bank. still ran fine,
So I decided to check back pressure on the cat. I pulled sensor one out of bank one (really a joyously tight squeeze in there) hooked up my gauge and got 0 back pressure. revved it and all nothing. hooked sensor back up pulled truck out of shop and it commenced to running like crap. I mean bad. running worse than before I got it. Popping P0012 code continuously, and tons of misfire codes associated with bank 1 ..cyl 3 etc.. I tried swapping coils, pulled coils and checked spark with a tester and firing away looks like tons of good spark.
Now the weird part is : looks like bank one is dead. I can unhook any coil pack and/or injector and it runs the same and sounds like it is missing. if I unhook one off of bank 2 it almost dies or does. so bank 2 seems to be running fine. it will start and run but sounds like it missing sets flashing check engine light and backfires and stalls like crazy. I even second guessed my pressure gauge and unhooked exhaust manifold from pipe and it sounds even prettier when it backfires out of there but no change. I pulled cam sensors and cleaned it again and even tried swapping them since they looked identical but no change so I put them back.
Now I can only surmise that I am out of time somehow? or I have a gremlin perhaps? I like working on cars (usually) but this one is getting old. how do I verify what is wrong. if it is timing related how do I verify that now definitively once my marks moved I really cant figure out how to tell if it is in time? Since it has all new parts and they all ran beautifully till now. could it possibly be the vct solenoid doing all this? I plan on changing it when it comes in but surely it cant cause this many problems.. I unhooked it no change, and it does it at a cold idle and any rpm. really runs worse at idle but bad at any rpm.
Accent MC (2006-11) :: 2008 GS - Misfire On 3 Cylinders / Rough Idle And Poor Acceleration
After scouring through hundreds of threads on this forum (which is Awesome, BTW), it seems as if this misfire / rough idle thing is fairly common (which is scary!!). CEL is on steady. Had the codes pulled; P0301, P0302, P0303. At the recommendation of the mechanic, I had the plugs replaced...no improvement. He then replaced the ignition coils...no improvement. Just finished replacing the MAP sensor. This actually had a VERY temporary positive effect. However, after about 5 miles of driving, the misfiring returned. Took the car to the Hyundai dealership, and they acted as if they didn't want to fool with it. They referred me to a couple of local repair shops...????
View 8 RepliesFord F-150 (2004-2008) :: 2006 - Misfire On Cylinder 1 / Code P0301
I have a 2006 F150 with a cylinder #1 misfire only code p0301. I have done new spark plugs, new coil packs, and new fuel injector on cylinder #1 with no luck. What to do next?
View 5 RepliesFord F-150 (2004-2008) :: Code P0300 - Rough / Low Idle After Timing Set
Just did the timing chain, phasers, oil pump and lash adjusters on my 05 5.4 s-crew. Always had a bit of a rough idle but now it's worse. If the truck idles for an extended period it sets a p0300. Just off idle the misfire is gone. It does seem a touch down on power but otherwise runs great. I did have the plugs out during the work. I cleaned them, applied anti seize and re installed. The previous owner had the plugs and COPs changed 10k miles ago. Plugs are motorcraft and coils are aftermarket.
I monitored with oreillys crappy scan tool and the miss only happens at idle. It is not a dead miss; unplugging COP on each cylinder still makes it worse.
Truck idles warm at like 570 rpm and if I hold my foot on the pedal to raise rpm a bit miss goes away.
Each cylinder is logging misfire counts with no rhyme or reason. The only thing odd during the timing job was 4 spark plugs were partially loose.
I'm sure the timing is correct; I used the OTC crank tool and for timing kit. Truck has 150k, front 02s are fairly new...
Ford F-150 (2004-2008) :: 2005 - Rough Idle - Code P0012
I have a 2005 f150 5.4 3 valve with the p0012 code the truck runs good has a rough idle not sure if it is worth changing the vct or not the truck has 190000 miles....
View 1 RepliesFord F-150 (2004-2008) :: Truck Is A Bit Rough At Idle - B1360 Code - No CEL
So I bought a 2006 F150 stx reg cab with the 4.6l motor with 90k miles on it a few weeks ago. It was in really good condition and I couldn't pass the deal up. All in all, I love this truck. However at idle the truck is a bit rough. No check engine light, but a bit rough non the less. So I hooked up my obd2 torque app and I see I have anywhere between 6 and 60 total counted misfires, but none detected by individual cylinder. So I ran a scan and have a B1360 code without the CEL on. So I changed the plugs and coil packs and cleaned the k&n filer (non cold air filter, just a replacement k&n) and I still have all the symptoms and the b136p code. So I Google the b1360 code and there's very little on it. Basically says open circuit ignition.
View 1 RepliesDodge - Durango :: 2003 - Code P0300 Random Misfire / Engine Running Rough
Just started getting a p0300 random misfire code on the durango a couple days ago. pretty sure it isn't moisture related since it started on a nice sunny day. it was running pretty rough so it was obvious that it was misfiring. I changed the plugs since it was about time anyway, and they needed it and I cleared the codes. new plugs (put in the oem champion copper plugs) didn't make the problem go away. The engine still ran rough and the code came back. 2 of the plugs looked like they may have been fouling a little bit. they were a fair bit blacker than the rest of the plugs. I went ahead and changed the coils on those two cylinders and reset the codes again. Still runs rough and the p0300 came back. where do I go from here? I am not getting any specific cylinder codes so it makes sense to me that it isn't one or two cylinders not getting spark. 2003 durango 4.7 ....
View 6 RepliesFord F-150 (2004-2008) :: 2006 - Rough Idle
I have a 2006 f150 I just bought after my F250 was stolen. It has about 70k miles. It has been running pretty rough ever since I got it. It finally threw codes so I tried to address all the issues. Changed out a couple coils and all the plugs (motorcraft platinum). The camshaft sensor was also bad. Truck runs much better but still has an idle issue I cant seem to nail down.
I assume its something to do with air intake. It doesnt happen all the time. It runs rough and knocks and sometimes dies. If I give it gas it stops. I read it could be the idle air intake valve, but then I read that this model doesnt have one. I also read that air intake issues dont normally throw codes. Are there any common problems I could look for? Would cleaning the throttle body do any good?
I know the basics, but this kind of thing is tough for me to troubleshoot. You may have already seen me post this problem, but I didnt get much response so I thought I'd try one last time.
Ford F-150 (2004-2008) :: Rough Idle / Engine Stall Out While In Park - Lean Code
My 04 F150 has started having a rough idle. While in park the engine will stall out with the A/C off. Also when in drive the truck will idle close to 1000rpm's. I had to the fuel filter cleaned and also the MAF sensor cleaned. Also did a vacuum check on it. Pulled the code and it's throwing a Lean Code. What else should I be looking for?
View 12 RepliesFord F-150 (2004-2008) :: Rough Idle And Hard Miss Under Load - CEL Code P0306
2005 f150 5.4.
I have a slightly rough idle and can feel a miss at 1600 to 2000 RPM. Sometimes running about 65 MPH up a slight grade I can slowly press the gas pedal and the engine will begin to miss much worse, causing the truck to shake pretty bad. When it gets this bad it will slowly flash the CEL and I get a P0306 code (Cyl 6 missfire).
The truck has 148000 Miles on it and the plugs were replaced at approx 120000 by the dealer.
In the last week I have replaced the plug in cylinder 6 (looked ok) and have replaced all the COP's along with the fuel filter and the injector on #6.
I haven't been able to get it flash the CEL light or throw a code since replacing the COPs though and I am at a loss at to what to try next.
Ford F-150 (2004-2008) :: Engine Starts To Run Rough And CEL On Within Seconds After Idle - Code P0351
2004 F150 5.4 3v. I bought the truck with 102k on it, it now has 124k. In the morning, when the outside temp is between 30-50, the engine starts and runs fine. When I get to the first red light ( about 1 mile away) within seconds of the engine at idle, engine starts to run rough and CEL. Every time the code is p0351. If I let it sit in the driveway to full warm up... no problem. If I start the truck, shut it off and restart...no problem. It only happens at the cooler temps. I have changed plugs, used motorcraft, nickel antiseize, torqued, etc. Ford changed the coil, I have changed the coil, cleaned MAF. As soon as I cross the intersection, light stays on, rough running clears up, and runs like a champ for the rest of the day.
View 2 RepliesFord F-150 (2004-2008) :: 2006 - Rough Idle With Many Codes
I just received a 06 F150xl with a 5.4 triton and idles rough with the following codes! p0357 p0012 p0340 p0344 p0351 p0352 p0356 p0358 p0357 p0102 p0113 p0353 p0354 p0355 It's amazing the truck even runs and with no light on but it will accelerate. someone mentioned to clear the codes and drive it 50miles or so and read them again.
View 9 Replies