Ford F-150 (2004-2008) :: 2007 Won't Run / Engine Would Shake At Idle When Hot
I have a 2007 F150 with the 5.4 FFV. Early last summer my truck started acting like the harmonic balancer was going bad, when it was hot out my engine would shake at an idle. Then in October it threw a check engine light, wouldn't get over 20 mph and was shaking the entire truck. The codes said my timing was out so I replaced the timing chains, guides and tensioners, which were bad on the passenger side. When I started it back up it ran rough, and the check engine light came back on with a "bank A over-retarded" code.
So I went back in thinking I had put the chain on one tooth off. Got it back together and it ran the same way. After doing some soul searching on this website I determined the VCT Solenoid for the driver's side may be bad, and I went back in a third time and replaced the solenoid. Now it runs worse than it did the first time, it won't even idle and it is nearly impossible to start in the first place... This truck only has 103,000 miles and was running great before this...
Ford F-150 (2004-2008) :: 2007 - Intermittent Rough Idle At Low Speeds When Engine Is Warm
Still showing the same codes (per repairman) and still having the intermittent rough idle at low speeds when the engine is warm. It has been so intermittent that I could almost live with it.
So repair guys first replaces the VCT's and runs fine until warmed up and the problem reoccurs with the same codes. He replaces both cam phasers and tensioners today and still same problem and same codes which point to the VCT and cam phasers.
Truck has 80k, city driven, oil changed every 3k or so. Burns ethanol and still runs great at speeds over 10 mph even when this problem appears.
Ford F-150 (2004-2008) :: Rough Idle Almost Like A Misfire
I hopped in my truck this morning, fired it up, and it idled nicely. I drove around the corner, and noticed that the truck was barely responding to the throttle. Then things got shaky. It was a very rough idle, almost like a misfire. But I managed to get the gas to respond and got the revs up to about 3K and it seemed to run smooth.
No CEL either. Currently, I have no place to really look at my truck as I don't have a garage, or driveway for that matter. I don't have a scanner that can read live data either. I'm limited in my tools currently as well.
Ford F-150 - 1997-2003 :: 5.4L Engine Stutter While Turning - Misfire At Idle Or While Driving
My 2003 f150 5.4l has developed a slight stutter when I turn from a stop or go from reverse to drive or vise versa. I had thought it was the IAC so I replaced it but the issue is still there. There are no engine codes and it does not miss fire at idle or while driving. The problem appears to be happening only when the a/c is on. Could the belt be the cause?
View 4 RepliesFord F-150 (2004-2008) :: Rough Idle Cylinder 3 Misfire
2004 Ford F150 5.4 Triton 3V Vin5.....
How this started, Drove through a lot of water as our City was in a flood on my way home and and the truck started running rough and got worse over time, I can now barely get to 40 mph as it starts to ping and sputter with no power.. the truck has been parked and not driven while in the shape it's in.
The truck keeps giving me error code P0303 Cylinder 3 misfire detected, P0174 System too lean (Bank 2) and at times another error P0300 saying multiple cylinder misfires detected.
After clearing the codes, I got new codes stating Misfire on Cylinder 2, 3, 4, 6. System too rich (Bank 1) System too lean (Bank 2)
Cleared the codes again and I'm back to Cylinder 3 misfire and System too lean (Bank 2)
What I have done so far... All repairs with in a few days...
1. Changed all spark plugs.
2. Changed all Coil Packs.
3. Changed number 3 fuel Injector.
4. Changed the Oil and Filter. (no water in the oil)
5. Changed the MAP Sensor.
6. Changed Bank 2 O2 Sensor 1 and 2.
7. Loosen the Catalytic Converter on the drivers side to re-leave back pressure thinking the Cat was plugged, still loss of power. I also drilled a small hole in the exhaust at my lowest point to see if it had water in it and it does not.
Checked for vacuum leaks using starting fluid around the intake manifold, no change in idle.. I also checked to make sure the vacuum line was still connected on the back of the intake manifold, I have found nothing leaking.
I also had cleaned the throttle body and changed the throttle position sensor.
Repairs within the last 6 months or less...
8. Replace passenger side cat.
9. Replaced both Bank 1 OS Sensors
9. Replaced Timing chains, Gears, Guides, Guide Tensioners, Oil Pump and pickup tube, Water Pump.
Cam Phasers are fine.
And number 3 coil is getting spark I changed the Ignition Coil again thinking maybe another bad pack.
Still #3 misfire and System too lean (Bank 2).
I am at a loss and not sure what to try, except for a compression test on cylinder 3 but I honestly don't think it's compression or a burnt valve.
Ford F-150 (2004-2008) :: Misfire And Rough Idle - EVAP Sensor
My 2004/ 4.6L F-150 had misfire issues and rough idle. Since changing the plugs and a COP the idle is better. It seems to stutter a bit at low RPMs around town, but it fine at higher RPMs. What to check next. Also since fixing the misfire and clearing the codes from the computer it won't enable all the emissions monitors. I've drive over 100 miles and the EVAP monitor still isn't on. The truck has about 213K miles on it.
View 3 RepliesFord F-150 (2004-2008) :: Misfire / Rough Idle Under A Bit Of Load (acceleration) And Uphill
2005 Ford F150 lariat 5.4
I had a misfire under a bit of a load (acceleration) and up hills. I changed spark plus with OEM Motor craft ones, truck ran super nice for a couple week.
Had the engine light flash, slow down and the RPM go up a tiny bit then back down and the light goes off
Now I'm back to miss fire different location, and a rough idle. I've swapped coil packs around and the miss fire stayed on cylinder 4.
Spark plug screwed or injector or ?????
Ford F-150 (2004-2008) :: Rough Idle / P0012 - Misfire Codes Associated With Bank 1 And Cylinder 3
5.4 3v. my last few weeks have not made me a fan. Here are the details:
I bought a 2008 F150 XL 5.4 3v with a cam phaser knock. Have done other timing jobs in past with no trouble so I was not too afraid to tackle this one. famous last words...opened the motor (shout out to the passenger side valve cover and its designer here) and found semi damaged roller follower on driver side. Worn cam lobe on the corresponding lobe and a loose chain on passenger side. proceeded to :
Change all timing components: phasers, chains, tensioners crank sprocket, all applicable bolts and BOTH cams as well as all lash adjusters and roller followers. most looked fine in fact all really did with a bit of wear on a few roller followers but only one bad one. engine didn't look to bad pretty clean.
Double and triple checked my timing chains and it was spot on. dark link on spot on crank, two dark links on the L and R dead on. put it back together. oh yes, changed all plugs with motorcraft ones, didn't even break one. did not change vct solenoids because I falsely assumed I could change the later easily if needed. they looked ok. screens intact etc... silly me for not realizing how kind Ford was in 2007 and later to necessitate removal of valve cover. I was reading a previous one on the how tos and assumed later models would be the same since it was the same sensor...
Cranked truck ran great. I mean perfect. sounded perfect. ran like a scalded cat. till it got to hot idle then it started doing its thing. rattle shake till you revved it. ran fine just wouldn't hot idle fine especially in reverse or under slight load. replaced driver side vct since ford only had one and I started on the easy side ordered the other one waiting for it. seemed to improve dramatically meanwhile I am driving this truck to test it. I drove it to work 50 miles each way and it ran great.
After a few trips it popped the P0420 light, seemed to run ok, cleared it watched it wouldn't come back. O2 sensor did seem to imply a bad cat on bank 1 since it seemed sensor two was mimicking sensor one and not staying stead like the other bank. still ran fine,
So I decided to check back pressure on the cat. I pulled sensor one out of bank one (really a joyously tight squeeze in there) hooked up my gauge and got 0 back pressure. revved it and all nothing. hooked sensor back up pulled truck out of shop and it commenced to running like crap. I mean bad. running worse than before I got it. Popping P0012 code continuously, and tons of misfire codes associated with bank 1 ..cyl 3 etc.. I tried swapping coils, pulled coils and checked spark with a tester and firing away looks like tons of good spark.
Now the weird part is : looks like bank one is dead. I can unhook any coil pack and/or injector and it runs the same and sounds like it is missing. if I unhook one off of bank 2 it almost dies or does. so bank 2 seems to be running fine. it will start and run but sounds like it missing sets flashing check engine light and backfires and stalls like crazy. I even second guessed my pressure gauge and unhooked exhaust manifold from pipe and it sounds even prettier when it backfires out of there but no change. I pulled cam sensors and cleaned it again and even tried swapping them since they looked identical but no change so I put them back.
Now I can only surmise that I am out of time somehow? or I have a gremlin perhaps? I like working on cars (usually) but this one is getting old. how do I verify what is wrong. if it is timing related how do I verify that now definitively once my marks moved I really cant figure out how to tell if it is in time? Since it has all new parts and they all ran beautifully till now. could it possibly be the vct solenoid doing all this? I plan on changing it when it comes in but surely it cant cause this many problems.. I unhooked it no change, and it does it at a cold idle and any rpm. really runs worse at idle but bad at any rpm.
Ford F-150 (2004-2008) :: 2006 - No Power / Rough Idle / Random Misfire Code
Have an 06 F150 5.4 3v with no power. spark knock. rough idle. wants to die while driving, and random misfire code. Have replaced fuel pump, filter, coils and plugs. What to check next? Already thought of EGR - it doesn't have one.
View 4 RepliesFord F-150 (2004-2008) :: 2007 - Cylinder 3 Misfire Code
I know there is a tun of info on the spark plug problem on the f-150. Here is the problem I have and I don't know where else to look.
Cylinder #3 misfires
1. swapped coil with #2 cylinder and still throws #3 misfire code.
2. Changed the plug on #3 and still the same code #3 misfire.
Where to look next?
Ford F-150 (2004-2008) :: 2007 4x4 5.4 Triton - Misfire Causing Overdrive To Act Up
I just bought a 2007 f150 4x4 5.4 triton with 69 thousand miles less than a month ago. Since then the transmission has been rebuild but come to find out a misfire will cause overdrive to act up, and it just recently started misfiring badly. It was throwing a code. 2 coils were replaced and still misfiring. It's not throwing a code anymore. No check engine light flashing or nothing.
View 1 RepliesFord F-150 (2004-2008) :: 2007 - Bucking And Kicking / Misfire On Left Bank
Truck has been taken care of, new Motorcraft plugs done 15,000 ago, never had any issues with truck until recently. Started bucking and kicking, threw CEL light, pulled codes. P0018, P0022, P0300, 305, 307 and 308. All of the misfires seem to be happening only on my left bank. I threw in a new camshaft position sensor just for the hell of it. This issue goes away and comes back intermittently. I drove it for a day and it did fine. Had power and then started it later to go home and it was misfiring, got to a stop light, cycled key and everything went back to normal. 2007 Ford F150 Lariat 5.4l Triton....116,000k....
View 11 RepliesFord F-150 (2004-2008) :: 2007 XLT Missing / CEL Codes Ignition Misfire 8 And Rich Fuel
My 07 xlt 4x2 4.6 (49700 miles) started missing a couple of weeks ago. Did it for 2 days, the Check Engine light came on, then it quit missing and ran normal. CE light was still on, so I had the code read and reset light. Got two codes: ignition missfire #8, and rich fuel. I assume the rich fuel was caused by raw gas in the exhaust.
Anyway, the truck ran fine for two or three days then started missing again. Checked #8 by taking the wiring connector off #8 COP - rough idle unchanged. Pulled COP off #8 and #7 and swapped. Rough idle unchanged and confirmed miss was still #8 by pulling COP connector. With #8 connected, disconnected #7 (with COP from 8) idle was significantly worse.
Replaced #8 plug. Same miss. What to check next?
Santa Fe (CM - 2007-12) :: 2008 - Random Cylinder Misfire / Vehicle Shuttered And Driving Power Lost
I have 62,500 on my 08 Santa Fe... never had any engine problems, but today, started the vehicle, drove 1/2 mile in town at 25 mph, turned a corner and the vehicle shuttered and lost driving power. At the same time, the check engine light came on and flashed continuously. I drove 1/2 block (around two corners in town) with the on/off studder and loss of power. I pumped the accelerator just to keep it from killing. As I stopped at the next corner and idled the vehicle regained power. I pulled over and called the dealership service department and they recommended I drive it home (blocks away) and turn the engine off, then try to restart it and if it started drive it 30 miles to dealership.
Did that, engine light came on steady and vehicle had full power. Long and short... the code was P0300 Random CYL Miss Fire Fault (random cylinder miss fire). After scanning the vehicle, test driving it and inspecting it as they do, they could not find a source of the problem or duplicate it. They cleared the code and promised that if it happened again they would credit me the $90 diagnostic fee I paid today for them to find nothing and apply it to a problem they couldn't find. They were willing to try and warranty it even though it is 2,500 over warranty if it had needed parts. Has this cylinder misfire happened to any of you? I've never had a problem like this really go away, so I'm expecting it will show up again. Also, they want to replace the timing belt (at 60K) as a preventative measure. What do you think? Can I wait till 80K?
Ford F-150 (2004-2008) :: Engine Misfire - Injectors Stuck Open
I have an 06 F150 with 31K miles, with the 5.4 V8, and recently experienced an engine misfire condition, caused by two stuck open fuel injectors. The dealer fixed everything back, but, said its not covered like the 05's, so I had to pay.
Why the 06 5.4 with the same problem as the 05's, is not covered? Seems to me like Ford still has a problem with stuck fuel injectors on the 06.
Chevrolet - Suburban :: 2007 - Misfire After Working On Engine / SES Light Flashing While Driving
I replaced the oil pressure switch on an '07 Suburban 5.3L because the oil pressure was showing low once the engine warmed up. That did nothing, then I found out about that little filter/screen under the sensor. I intended to remove and clean the filter then reinstall it. While I was pulling it out, I dropped it back behind the engine and couldn't find it. I checked online and found a few people in other forums that said to just remove the screen as a "fix", so I left it out and put the sensor back in, just to get the vehicle drivable. It started right up and ran fine for me, parked it, and a after sitting for a few hours it started popping while driving with the SES light flashing on the drive home.
Code P0300 was set, no cylinder specific misfire codes were present. I checked the misfire data and cylinder #6 showed tens of thousands of misfires, #5 showed several hundred, but I think it was just picking them up from #6 since #5 is right after #6 in the firing order. I disabled each injector with a scan tool, all changed the idle except #6, it did absolutely nothing. #6 fuel injector had good pulse to it, I connected a fuel pressure gauge and put power/ground to injectors #6 and #4, both dropped the same fuel pressure. I did the "cylinder deactivation" test on the scan tool for the four cylinders that have it, they all did the exact same thing - the engine bogged way down for a couple seconds and then died. Is that normal? I can't say I've ever seen a V8 engine die before when running on 6 or 7 cylinders. I checked compression on cylinder #6, it showed very low, almost zero, but I tried it a few times and it would show just a little compression at times... valves staying shut? I'm thinking when I opened the pressure relief valve on the gauge and the piston was near the bottom of the cylinder may be when it showed some compression. I also switched the coil/wire/plug from #6 to other cylinders and the miss did not follow.
Could having that screen out cause this problem? Having the engine die when deactivating the cylinders makes me wonder if maybe it's commanding all four at the same time, although the test shows each cylinder being controlled separately. Using a MODIS, not a TechII. I just got done putting in a new filter/screen to see if it would make any difference, and of course it didn't.
Ford F-150 (2004-2008) :: Misfire Codes / Engine Shuddering Under Acceleration When Cold
My new to me 04 4.6 shuddered and misfired really bad last week, got couple misfire codes. I changed plugs which were really bad, like burnt out to .080, got a HEI ignition tester and got a healthy spark from all the coil packs. Drove it today and ran much better but still would shudder under acceleration when cold, wasn't as bad when warmed up but still noticeable. I thought if I got a spark with the tester that means the coil is ok? or is that not the last word in coil health. Or should I look somewhere else like injectors ? Haven't got any codes since plug change.
View 1 RepliesFord F-150 (2004-2008) :: 2005 - Check Engine Light Came On - Cylinder 5 Misfire
I have a 2005 f150 with 96,000 miles. Long story short, last August I was headed to the mountains going up a steep long hill and the engine light come on. once i was over the pass the light went off. During my 4 wheelin' trip it never came back on until I was headed home and going over another pass and then it stayed on for a couple of days. I had it checked and it was a cylinder 5 misfire. I did some research and found that replacing the coil cover might fix the problem and if not the spark plugs would need to be changed.
I changed the coil cover, problems solved... until I headed to the mountains. light came on and then eventually went off later that day. I didnt think much of it. then a few months later i was headed to the mountains again and the light came on in the same place on the steep incline hill. I. took it back to the shop, same reading. I decided it was time to replace the spark plugs anyways so I would invest. I have new plugs and everything is good however, I had no plans to go to the mountains in the near future. Now, a few months later I headed to the mountains and crossed my fingers it would not come on but it did.
I've done the research again and it seemed like the coil cover and spark plugs are usually the cause of the problem...however I have changed mine. The light is now off again. I don't understand what is triggering the problem and what is really happening and if it is safe to keep taking to the mountains with this happening. I did notice that everything was fine at 60MPH but once i hit the hill and steeped on the gas to go 65 and hit 4-5RMP that is when the check engine light came on...
Ford F-150 (2004-2008) :: Wrench Light And Random High Idle After Driving?
I've got a 2006 F150 FX4 with a 5.4L 3V
A couple of months ago, I got a random "amber wrench light" on the dash. After I shut the vehicle off, it would go away. Over the last month, it's been coming back on more frequently....pretty near every time I drive the truck. I'm also noticing a bit of a dead spot in the pedal at times....though it's never failed me completely.
After a quick Google search, I was led to believe it could be a throttle body issue. Before replacing the throttle body, it was suggested to remove and clean the throttle body itself....which I did.
I'm still getting the amber wrench light, but now I'm also getting a random high idle after driving. If I throw it in park, it will idle up to 2,000RPM. I initially assumed I may have created a vacuum leak of some sort, but when I shut the engine off and restart it (or even blip the key off and on again quick before the engine dies, it comes back to life and idles fine? This tells me that it isn't a vacuum issue.
The strangest part, is that it's not tripping any codes what so ever?