Tiguan :: Intake Manifold Failure - CEL Flashing / Rough Idle
Well my 39000 mile run of zero faults ended with a intake manifold failure. The check engine light came on whilst on a Yosemite trip, I checked fluids, etc, car was driving ok, but when I reached my destination I noticed a rough idle. Next time I started it a couple of days later the check engine light was flashing, and it was a rougher idle, so I knew enough not to drive it.
The closest dealer fixed it (no cost to me) under the power-train warranty (nice customer care from Michaels Fresno plus they had the parts in stock).
I learned a couple of things being stranded:
1) Problems happen but they can be accurately diagnosed and fixed.
2) $150 coverage for towing on my insurance policy doesn't get you very far. But I wanted to take it to VW to simplify any warranty work and have it repaired quickly, so I paid quite a bit of overage.
3) Tow trucks don't carry a family of 4, so the logistics of getting a rental car to get my family home wasn't simple.
4) If you have to be stranded, Yosemite valley with the free shuttles, is a pleasant place to be.
5) If you need a reminder just how good a car the Tig is to drive, just try renting a Jeep Compass for few days...
Diags for the record:
GFF found 9 faults: P0170, P0300, P0301, P0302, P0303, P0304, P0507, P068A, P2015. Found arm for intake runner flap came apart causing vacuum leak that caused engine misfires.
Parts
1 x 06J-133-201-AS Manifold
4 x 06J-998-907-B Repair Kit
Tiguan :: CEL On - P2015 Intake Manifold Runner Position Switch Code
I have a 2011 Tiguan S 4Motion with just over 63k Miles which for the most part has been problem free and great to drive since I leased it at 40k miles. About 2 weeks ago my CEL came on and I used the Torque app on my phone to check the code and it was the apparently well known P2015 intake manifold runner position switch code. The car was running perfectly fine so I cleared the code and it stayed off for about a week before coming back on with the same fault again yesterday. I have a couple of questions for the much more knowledgeable than I people in this forum around this code.
First - I've read in several places that VW has placed an extended warranty on the manifold and fuel injectors for the 2.0 TSI and that this code is usually an indicator that the manifold needs to be replaced under this warranty. What I haven't found though is conclusive info on is whether the 2.0T in my 2011 Tiguan is covered under this extended warranty. Since this code so conveniently is popping up just 3k miles past the end of my 60K mark, I'd like to know this. I leased the car from Enterprise, not a dealer so I'm worried that whatever dealer I take it too will try to bend me over on the service so the knowledge that the manifold is still covered would be at least some comfort.
Second - I won't be able to get it in to a service department until mid next week and I have a 300 mile trip to make this weekend. The car is driving fine as far as I can tell so I'm not overly concerned. I do my own basic maintenance i.e. oil changes, plugs/coil packs etc. but I'm thinking changing the manifold would be a little bit out of my comfort zone..
Monte Carlo :: Intake Manifold Exploding On GM V6 3.8L
Turned the key on my 2002 MC SS, V6, 3.8L, and the Intake Manifold exploded.
Intake Manifold Exploding on a GM V6, 3.8L? It sounded like a 12ga shotgun. Fortunately no one was looking into the engine compartment at the time as they likely would have been killed given the amount of shrapnel from this explosion. Note that the explosion was powerful enough to blow off the oil cap, which is screwed on with very thick threads.
The vehicle was at my mechanics at time and in his forty years he's not seen an intake manifold explode save for those residing on Top Fuel or Funny Cars.
Golf IV R32 :: Nozzle On Intake Manifold Broke
One of the nozzles on the back of my intake manifold broke off. I don't know how to better explain it. The ones the back of the manifold closest to the firewall there are several hoses that hook to the manifold. The second one from the left broke.
View 7 RepliesGolf IV R32 :: Intake Manifold Shifter Not Working
I'm having a problem with the intake manifold shifter not working on my r32. I've tried all of the normal fixes, the shifter rod itself and the vacuum diaphragm that opens it are both functioning correctly, all of the vacuum lines are new and not leaking. Connecting vacuum directly to the diaphragm causes the shifter to immediately open. I've tried 3 different solenoids with the same result, all open when 12v is directly applied, but the manifold doesn't open at it's RPM point like it's supposed to. The solenoid sees a constant ~11v under all conditions, regardless of engine RPM. I've traced this wire back to the ECU and confirmed it's not damaged. No CEL other than for the SAI missing.
At this point, I'm assuming whatever circuit that controls this in the ECU is fried (cruise control doesn't work either.) I have an extra 24v vr6 (2.8) ECU sitting around which from what I've read uses the same hardware, just a different flash. This may be a stupid question, but if I were to take this to UM to get a performance flash, would I be able to basically overwrite the 2.8 ECU and make this work in the R? Would there be any issues with the immobilizer?
Golf/GTI VI :: CEL Code P2015 - Intake Manifold Bad
My husband has a 2011 GTI, which has just hit the 40k mileage mark. His CEL started coming on in March, but we figured it was due to him not tightening the gas cap enough, as he'd open and relock the gas cap, and the CEL would go away within a few restarts of the car. Took it into the stealership last week, got the 40k service (which was a bit of a rip-off in itself), and then got told the manifold was bad.
This is the exact text for the invoice: "Checked the vehicle for codes and found code P2015. Traced the intermittent failure to the intake manifold valve flap sensor failing."
I've seen a lot of posts around this problem, for many models and years, but it seems like most people managed to get it repaired under warranty / TSB. So I have three questions:
1. In the OBD codes, does it store date as well as code? In other words, is there a way to prove that this failed under 36k miles?
2. What's the process for getting this escalated to VWOA customer care, since I feel this should be taken care of under warranty?
3. The dealership we took the car to (which is not where we purchased the car, but is just closer to home) was shady, and the guy we worked with was, to say it nicely, a jerk.
Dodge - Charger :: Can Oil Leak Out Of Intake Manifold?
Can oil leak out of Intake Manifold? i have Oil around lower intake manifold gasket. is this serious issue?
View 11 RepliesGolf IV R32 :: Chamfering Noise From Intake Manifold On Idle
I have a chamfering noise coming from my intake manifold on idle. sometimes its there and sometimes its not, it goes away with any application of throttle.
View 9 RepliesGolf IV R32 :: Stock Intake Manifold Valve Broken?
I am just wondering at what revs the stock intake manifolds are meant to switch over as i think mine is stuck and not moving.
View 23 RepliesSanta FE SM (2001-06) :: Fluid Leaking At Intake Manifold
2.4 Santa Fe ... I just took my Car to MOT inspection and found out there's a leak at my intake manifold and it's coming out of this place. it feels like brake fluid but my brake fluid is full?? I have seen many cars but never seen a part like this before. what is it doing there and why is it leaking ?
View 6 RepliesPassat (B5) :: 2003 - Major Oil Leak Under Intake Manifold
My friend and I are working on her '03 1.8t and I noticed a huge oil leak under the intake manifold. It looks like there's a tube that has broken off and is now just spewing oil all over the place. I tried to get pics the best I could, so here they are....
I'd imagine its something that needs to be fixed asap.
Phaeton :: Intake Manifold Linkage Motors Are Broken?
I noticed that my links for my intake manifold motors were broken i went to the dealer they didn't just sell the link they wanted 450.00 dollars for each one .
View 2 RepliesGolf/GTI VI :: Clicking Sound Coming From Intake Manifold?
I have a small clicking sound coming from my intake manifold. I recently installed a boost gauge and it did it once after that... I shut the car off and I didn't hear again until 1000 miles later and its back, why it would be clicking like this but its annoying
View 6 RepliesNissan - Frontier :: Signs Of Bad Intake Manifold Gasket?
On a 1997 Nissan pickup 241,000 mile 2.4 liter. What are the signs of a bad manifold gasket. How can i test it.
View 6 RepliesFord F-150 (2004-2008) :: Intake Manifold Replacement?
Looking for any pictures or directions on replacing the intake manifold on the 2004 F150, 5.4. Got all the parts with the pulgs, and ignition coils.
View 6 RepliesFord Excursion :: 2001 V10 - Intake Manifold May Be Cracked
What are signs the intake manifold may be cracked? 2001 V10 Excursion....
View 4 RepliesFord F-150 (2009-2014) :: Intake Manifold Swap?
Will an intake manifold from a new mustang 5.0 fit on a 2014 F150 5.0?
View 3 RepliesGrand AM :: 1998 3.1L V6 - Engine Intake Manifold Gasket Leaks
Leaking intake manifold gaskets on General Motors 3.1L V6 engines? Mine is a 1998 Grand Am with low milage (40K) and I have been told I need to spend $900 to replace the intake manifold gasket because it is leaking antifreeze into the engine oil.
View 8 RepliesBonneville :: 1995 Pontiac GM 3.8 Upper Intake Manifold Replacement
Just today,when replacing the UIM on a naturally aspirated 95 Pontiac Bonneville 3.8 with a Dorman upgraded type from my local auto parts, I ran into an issue. When following specified torquing sequences and specs , be very careful with the 1 long stud (#7), as it will split your new manifold there if you try to torque to 89 in/lbs. Took 1st back for replacement ,and the second new one started to split at the same place. Was using a brand new Craftsman in/lb torque wrench set correctly and following instructions exactly. I've seen a lot of excellent info on this UIM issue with the GM 3.8 ltr 1995-2004 years, but never this issue with the replacement ones. If I have to change this again will definitely go with the aluminum one.
View 1 Replies