Santa FE SM (2001-06) :: 2005 - Transmission Shifting Poorly And Getting Stuck In Limp Mode Intermittently
I have a 2005 2.7L Santa Fe that was shifting poorly and getting stuck in limp mode intermittently. I read up on it and found that it was probably an issue with the input/output speed sensors. The codes confirmed my suspicions and I replaced both the input and output sensors. The codes cleared and the tranny shifted like a dream. Unfortunately after 2 days and 100+ miles the car suddenly started down shifting randomly on my way home from work. The CEL came back on and the car went into limp mode. Could the sensor have gone bad again? Or could it be the wiring harness that plugs into one of the sensors? I don't understand why the car would be fine for a few days and then all of a sudden be acting the same way.
View 6 RepliesSanta FE SM (2001-06) :: 3.5L - CEL Came On And Car Will Go Into Limp Mode
I have been having a problem where the Santa Fe will drive great for a week, sometimes only a day and the engine light will come on and the car will go into limp mode. It will drop you from 65MPH to 10 MPH, if you put it in park the RPM's will race and stomping on the pedal will not affect the RPM's. After you turn it off for a couple of minutes it will drive ok again. I have replaced the Throttle Position Sensor and the Accelerator Pedal Sensor, cleaned all connections and checked wires in them. I have also cleaned the Throttle Body. The Dealer wants to replace the Throttle Body.
Had Engine Codes:
P0123 - Throttle Position Sensor 1 Signal Circuit High Imput
P1110 - Throttle Actuator Control System Malfuntion
P0222 - Throttle Position Sensor 2 Signal Circuit Low Imput
P1175 - Electric Throttle Valve Control System (ETS) Valve #
P1196 - Throttle Actuator Control System Limp Home-Stuck
Santa FE SM (2001-06) :: Code P1602 - Limp Mode / No Speedometer
About a week ago my 2002 santa fe suddenly lacked performance and the check engine light came on . At the same time I noticed the speedometer stopped registering. I later discovered the poor performance was due to the fact that the vehicle was in 3rd gear "limp" mode. The code generated is 1602 "failure to communicate between the ecu and transmission control module". At this point I hoping its just a faulty speed sensor that's causing the problem and not the transmission control module.
Does it indeed sound like a bad speed sensor or does it sound like a faulty TCM or could it be a break in the wires between the ECU and TCM? Also, is it safe to drive the vehicle in limp mode until i replace the part later this week?
Santa FE SM (2001-06) :: P0335 And P1372 - Engine Goes Into Limp Mode And Very Hard To Start
I have an issue with my 2004 2.7 Santa Fe. I keep getting fault codes P0335 and P1372, the engine then goes into limp mode and is very hard to start.
So far I have replaced the crankshaft position sensor, the MAF sensor, the spark plugs, new ignition coils and leads.
I have traced the wiring and found no shorts, the only thing which does not match the service manual is that I get 5v on the CKPS sensor wire when the ignition is on, it said it should be 0V.
The car can sometimes run for 50+miles with no issues - then stalls with codes P0335 and P1372. I have a feeling its worse when the aircon is on but cant be 100% certain/
Santa FE SM (2001-06) :: Transmission Started Going Into Limp Mode And Causing Check Engine Light To Come On
2002 Santa Fe, 2.7 AWD
The transmission has started going into limp mode and causing the check engine light to come on.
The codes given are p0750 and.... I think p0751, for shift solenoids C and D. There is also the generic Transmission Control Module code.
Limp mode only occurs at higher speeds although shifting feels a little rough at times in lower speeds.
If operated in manual mode the vehicle can be driven normally at all speeds without going into limp mode.
Fluid levels are fine.
With limp mode occurring in automatic but not occurring in manual mode, is it more reasonable to believe the solenoids are malfunctioning or the control module itself? I'm inclined to replace the solenoids but find it odd that the vehicle operates normally in manual. Also, can the solenoids be replaced without removing the transmission? It looks like I could get the pan off but am unsure if there is room to get the work done once it is removed.
Santa FE SM (2001-06) :: V6 Stuck In Sports Mode
I am the proud owner of a 2001 2.7L V6 Santa Fe. His mileage is roughly at 170,000 and I keep up with fluids and minor repairs (except an oil change, oops). Yesterday I was out with my fiance and our German Shepherd, we stopped at a restaurant and while we were inside our dog decided to redecorate the gear shift (PRNDL) with my ice tea. I noticed a problem immediately.
When I started to drive, there on the dash board was the normal "D" with and added "1" as if it were stuck between automatic and sports mode? I attempted to shift it to full sports mode to manually shift; I couldn't get him (the truck) to go above first gear, and nothing happened. I then attempted to fiddle with the gear shift to see if I could some how "knock" it back into automatic but nothing I tried worked.
The truck shifts easily into reverse, there's no abnormal sound coming from the engine, it drives just fine but refuses to go above first gear. I did discover tho that if I shift the engine quickly into neutral while driving and then down shift back to "D", the engine will shift easily but I assume this is not good on my transmission.
D and 1 light are on
Won't shift past first gear
Reverses just fine
Kicking it to neutral then D will shift the engine
Spilled something on the gear shift
I will try to upload a photo of what's going on with my dashboard lights referring to the "D" and "1" light.
Santa FE SM (2001-06) :: 2002 - Stuck In Sports Mode
Last night my girlfriend and i were coming home in her Sante Fe and it was driving perfectly fine. The check engine light was on, but it occasionally comes on so i figured it was probably just a sensor.
When we got in the car this morning and i put it in drive (automatic trans) it was in sports mode (i'm assuming because a "1" popped up under the "D")
And now i cant figure out how to just put it into normal drive. We spilled a tiny amount of soda on the shifter last night, maybe 3/4 a cup at the most.
Rodeo :: 2000 Transmission Stuck In Limp Mode?
My tranny is stuck in limp mode. I can manually shift it, but it won't shift on it's own. The 'automatic' part of the automatic transimission is definitely not working right.
I searched and checked for the usual suspects, low battery or alternator output (measured over 14v at batt. when on), and the range selector switch. I removed the switch, took it apart, cleaned it up, and reinstalled it. It looked like it was in decent shape inside, although it appeared to have had a bit of oil of some sort that had leaked into it. There was a bit of oil on that side of the tranny, around the gear selector and switch, but not enough to actually drip as I don't have any stains on my driveway where I always park. The only thing I haven't checked is the atf fluid level, as I can't seem to find the my wrench that will take off the fill nut. I'll get that figured out tonight.
The tranny hasn't been taken care of like it should, I've had the fluid replaced two or three times over 100k of ownership, but I'm not sure about the filter. Would the need for a filter and fluid change cause it to go into limp mode? Also, it's not throwing any CEL codes either.
Accent LC (2000-05) :: Transmission Limp Mode / Stuck In 3rd Gear
So yesterday, this had happened for the third time in 3 years owning this car. Unhooking the battery for 20-30 minutes resets the computer and it is ready to go for a while with no issues. This has become annoying though. What is causing the car to enter "limp" mode and stay in third gear? One time it happened, I brought it to AutoZone and they did a scan and came up with the speed sensor. I haven't replaced it because it didn't happen for a while after that.
View 11 RepliesNissan - Sentra :: No Power When Given Gas / Car Now Stuck In Limp Home Mode
A few months ago, my '00 Sentra developed a rough idle but I ignored it because it wasn't too bad, until recently at least. It had been getting progressively worse so I went out and bought some CRC MAF cleaner, which solved the rough idle altogether for about a day. After doing some errands, I started the car but it was now stuck in limp home mode, not matter how much gas I gave it, she wouldn't top 20 MPH and 2.5k revs.
I bought a new MAF, and that made the problem worse: in any drive gears or reverse, when given any gas, the engine would stall and die but when in neutral, I can rev it as high as I want to. I reset the computer and cleaned the new sensor to no avail. After re-installing the old sensor (which was visibly broken, it was missing an entire wire assembly), it will run poorly but will now drive with some quirks, and I don't trust it further than around the block.
My question is: with the new sensor, do I need an ECU reprogram, did I receive a bad sensor, or is there a compound problem? (I've heard with similar issues: bad alternator, bad TPS, bad IAC module, dirty IAC or TPS, clogged fuel filter, bad fuel pump, dirty air filter, among others.)
Ford Escape / Hybrid :: 2004 - Stuck In Limp-In Mode?
Wife come home the other day after leaving for work with the truck no going past 20KM to 30KM.. After some investigating it seems to be in Limp - In Mode. There was a Check-Engine light & after further investigation found a Vac hose with a leak, repaired this & test drove. Same issue.... then there was a loud hissing sound from the engine area so I investigate & now found the EGR sensor (DPEF pressure sensor ) had blow a hose & fried the sensor.
New sensor was replace along with 2-hoses cleared the engine light but the truck still will not go more then 20KM or 30KM max.. I checked the EGR valve with vac pump & engine stalls or so the valve is good. I have left the neg cable off the batt to try & clear the Limp-In mode without success. Looking for a way to clear the limp-in mode or do I need to clear it with a scan tool?
Lexus GX 2004-09 :: 2005 GX470 Stuck In Neutral Or Limp Mode
My wife started up my 2005 GX470 this morning to go to work and drove maybe a half mile before she noticed a problem. So she turned around and drove it back home in limp mode. She put it in park and got out.
Most of the Warning Lights are on ( VSC OFF, VSC TRAC, Anti Skid, Check Engine etc). I tried moving the shift lever but there was some resistance and some grinding noises. And it now seems to be stuck in neutral.
How to diagnose this myself? We only drive this vehicle in the winter, and it was fine the last time we used it.
Santa Fe (CM - 2007-12) :: MIL Comes On And Goes To Limp Mode
My 2007 Santa Fe was acting up at one time, then stopped doing it, and recently started again. My wife is the primary driver so I'm not always in the vehicle when it happens. When the vehicle is started cold, it will run a short distance then the MIL comes on and it goes to a 5 mph limp mode. After pulling over and shutting the vehicle completely down for a couple of minutes, it will run normally with the MIL still on. However, by the time I get back home to pull the codes, the MIL goes off. I don't remember the exact codes, but when it acted up last time I believe the codes had something to do with the TPS, Pedal Pos Sensor, and one other I can't remember.
View 3 RepliesPrius (2004-09) :: 2007 - Traction Control Computer Stuck In Limp Mode
I have a 2007 Prius and it will be my first car once I get my license. It has a bad traction control computer and is stuck in limp mode. I have a neighbor who has worked on these and will show me how to replace it. Right now I have two questions. I keep coming up with how to disable it not the actual part.
View 1 RepliesGolf IV / Jetta IV :: 2000 - Limp Mode / Stuck In 1st Gear And Error Code Of P0730
I have 1 month left on my AAMCO rebuilt transmission. I took it in a few weeks ago when it went into "limp mode" (Stuck in 1st gear). Eventually, they got an error code of P0730, which I believe is electrical-related. All was pretty good but then today, driving @ high speed on the interstate, I could not get into 4th gear...
View 1 RepliesSanta Fe (CM - 2007-12) :: Limp Mode - No Response From Throttle?
Driving on the motorway yesterday, all fine until i lost power..engine light came on, but I was able to continue driving for about 6 miles (trying to get to services) but eventually it would go no further, pulled over and found that the intercooler pipe had come off, replaced it but still no joy.
Recovery van attended and plugged in diagnostic and found a dpf fault and gas pressure valve fault, he cleared the light but i think the faults still remained.. so i had to be recovered home.
The engine will start but it does not quiet sound right, no response from the throttle and if i put it into drive the engine stops.. Its a 2007 2.2
Santa Fe (DM - 2013+) :: Limp Mode - Error Code P0488
I have a Korean spec 2014 Hyundai Santa Fe 2.2L R-eVGT 6AT 4WD. Around a year ago it started to go into limp mode i had it checked and the error code was p0488 (EGR) Throttle Control Circuit A Range / Performance.
It has gradually become more frequent to the extent it goes into limp mode within a a minute or so . so far the dealer has changed the EGR valve, TCM , the whole turbo assembly and it is no different. They have also stripped and cleaned the intake manifold and egr cooler.
Santa Fe (CM - 2007-12) :: 2008 Limp Mode - CEL / ESC And AWD Transmission Lights Blinking
I'm a little bit stuck here. This happened last night, and the dealer is closed today. I have a 2008 Santa Fe SE. It stalled last night, and when I turned it back on, I got a check engine light, the ESC light, and the AWD transmission light blinking. When I go to accelerate, it will not go passed 2000 RPM, and it is driving very sluggish. Its not knocking, or making any other kind of sounds. The air conditioning does not work, but the fan blows uncooled air. It accelerates extremely slowly, even with the petal mashed.
I plan on taking it in tomorrow, but I'd like to know if there is some way to reset the computer. I tried disconnecting the battery for about 30 minutes, but it didn't work.
Elantra XD (2001-06) :: LIMP Mode / Sluggish Driving But No CEL
I have a 2001 Elantra GLS 5spd with about 175k. Recently it started driving very sluggish. Under any more than minimal throttle during acceleration or load/resistance (i.e. climbing a hill), it bogs down and will decelerate. No check engine light, no codes, etc. I have replaced the TPS, catalytic converter, Spark plugs and wires, fuel filter, fuel pump, strainer, and fuel pressure regulator. Without any codes, I am at a dead end. I also unplugged the MAP and threw the code for it so I know it is functioning.
View 3 Replies