Santa Fe (CM - 2007-12) :: Limp Mode - No Response From Throttle?
Driving on the motorway yesterday, all fine until i lost power..engine light came on, but I was able to continue driving for about 6 miles (trying to get to services) but eventually it would go no further, pulled over and found that the intercooler pipe had come off, replaced it but still no joy.
Recovery van attended and plugged in diagnostic and found a dpf fault and gas pressure valve fault, he cleared the light but i think the faults still remained.. so i had to be recovered home.
The engine will start but it does not quiet sound right, no response from the throttle and if i put it into drive the engine stops.. Its a 2007 2.2
Santa Fe (CM - 2007-12) :: 2008 Limp Mode - CEL / ESC And AWD Transmission Lights Blinking
I'm a little bit stuck here. This happened last night, and the dealer is closed today. I have a 2008 Santa Fe SE. It stalled last night, and when I turned it back on, I got a check engine light, the ESC light, and the AWD transmission light blinking. When I go to accelerate, it will not go passed 2000 RPM, and it is driving very sluggish. Its not knocking, or making any other kind of sounds. The air conditioning does not work, but the fan blows uncooled air. It accelerates extremely slowly, even with the petal mashed.
I plan on taking it in tomorrow, but I'd like to know if there is some way to reset the computer. I tried disconnecting the battery for about 30 minutes, but it didn't work.
Santa FE SM (2001-06) :: 3.5L - CEL Came On And Car Will Go Into Limp Mode
I have been having a problem where the Santa Fe will drive great for a week, sometimes only a day and the engine light will come on and the car will go into limp mode. It will drop you from 65MPH to 10 MPH, if you put it in park the RPM's will race and stomping on the pedal will not affect the RPM's. After you turn it off for a couple of minutes it will drive ok again. I have replaced the Throttle Position Sensor and the Accelerator Pedal Sensor, cleaned all connections and checked wires in them. I have also cleaned the Throttle Body. The Dealer wants to replace the Throttle Body.
Had Engine Codes:
P0123 - Throttle Position Sensor 1 Signal Circuit High Imput
P1110 - Throttle Actuator Control System Malfuntion
P0222 - Throttle Position Sensor 2 Signal Circuit Low Imput
P1175 - Electric Throttle Valve Control System (ETS) Valve #
P1196 - Throttle Actuator Control System Limp Home-Stuck
Santa FE SM (2001-06) :: Stuck In Limp Mode And Would Only Go 20 Mph
My wife has a 2006 santa fe 3.5l limited over the winter it started acting up went into limp mode and would only go 20mph so I went and picked up a TP sensor well it went out of limp mode so I never changed the sensor well last month it started doing it again so I changed it out didn't work!!! comes up with 2 codes sometimes p2110 and p2118 but normally its p2110 2 times.
If I hit the break it kinda bogs down and pulsates.i took it to my mechanic since I couldn't figure it out and with advice from a hyundai mech. He changed APS didn't fix it so we changed throttle body with used of course didn't work I checked wires and didn't fined any open circuits what are the chances that i got a bad APS or TPS...
Santa FE SM (2001-06) :: Code P1602 - Limp Mode / No Speedometer
About a week ago my 2002 santa fe suddenly lacked performance and the check engine light came on . At the same time I noticed the speedometer stopped registering. I later discovered the poor performance was due to the fact that the vehicle was in 3rd gear "limp" mode. The code generated is 1602 "failure to communicate between the ecu and transmission control module". At this point I hoping its just a faulty speed sensor that's causing the problem and not the transmission control module.
Does it indeed sound like a bad speed sensor or does it sound like a faulty TCM or could it be a break in the wires between the ECU and TCM? Also, is it safe to drive the vehicle in limp mode until i replace the part later this week?
Santa Fe (DM - 2013+) :: Limp Mode - Error Code P0488
I have a Korean spec 2014 Hyundai Santa Fe 2.2L R-eVGT 6AT 4WD. Around a year ago it started to go into limp mode i had it checked and the error code was p0488 (EGR) Throttle Control Circuit A Range / Performance.
It has gradually become more frequent to the extent it goes into limp mode within a a minute or so . so far the dealer has changed the EGR valve, TCM , the whole turbo assembly and it is no different. They have also stripped and cleaned the intake manifold and egr cooler.
Santa FE SM (2001-06) :: P0335 And P1372 - Engine Goes Into Limp Mode And Very Hard To Start
I have an issue with my 2004 2.7 Santa Fe. I keep getting fault codes P0335 and P1372, the engine then goes into limp mode and is very hard to start.
So far I have replaced the crankshaft position sensor, the MAF sensor, the spark plugs, new ignition coils and leads.
I have traced the wiring and found no shorts, the only thing which does not match the service manual is that I get 5v on the CKPS sensor wire when the ignition is on, it said it should be 0V.
The car can sometimes run for 50+miles with no issues - then stalls with codes P0335 and P1372. I have a feeling its worse when the aircon is on but cant be 100% certain/
Santa FE SM (2001-06) :: Transmission Started Going Into Limp Mode And Causing Check Engine Light To Come On
2002 Santa Fe, 2.7 AWD
The transmission has started going into limp mode and causing the check engine light to come on.
The codes given are p0750 and.... I think p0751, for shift solenoids C and D. There is also the generic Transmission Control Module code.
Limp mode only occurs at higher speeds although shifting feels a little rough at times in lower speeds.
If operated in manual mode the vehicle can be driven normally at all speeds without going into limp mode.
Fluid levels are fine.
With limp mode occurring in automatic but not occurring in manual mode, is it more reasonable to believe the solenoids are malfunctioning or the control module itself? I'm inclined to replace the solenoids but find it odd that the vehicle operates normally in manual. Also, can the solenoids be replaced without removing the transmission? It looks like I could get the pan off but am unsure if there is room to get the work done once it is removed.
Santa FE SM (2001-06) :: 2005 - Transmission Shifting Poorly And Getting Stuck In Limp Mode Intermittently
I have a 2005 2.7L Santa Fe that was shifting poorly and getting stuck in limp mode intermittently. I read up on it and found that it was probably an issue with the input/output speed sensors. The codes confirmed my suspicions and I replaced both the input and output sensors. The codes cleared and the tranny shifted like a dream. Unfortunately after 2 days and 100+ miles the car suddenly started down shifting randomly on my way home from work. The CEL came back on and the car went into limp mode. Could the sensor have gone bad again? Or could it be the wiring harness that plugs into one of the sensors? I don't understand why the car would be fine for a few days and then all of a sudden be acting the same way.
View 6 RepliesTouareg :: 2007 Transmission In Limp Mode - Car Lurches
33K and no problems until this morning. Wife gets 400 yards down the street, car "lurches" and goes into limp mode. Transmission won't shift out of whatever gear its stuck in (going forward) Car will back up. Only indication of any possible trouble is occasionally the very first time the transmission shifts in the morning from 1st into 2nd its a little spirited rather than silky smooth.
View 5 RepliesPrius (2004-09) :: 2007 - Traction Control Computer Stuck In Limp Mode
I have a 2007 Prius and it will be my first car once I get my license. It has a bad traction control computer and is stuck in limp mode. I have a neighbor who has worked on these and will show me how to replace it. Right now I have two questions. I keep coming up with how to disable it not the actual part.
View 1 RepliesFord Super Duty (1999-2016) :: Transmission Would Not Work In Tow Mode And Caused Engine To Go Into Limp Mode
I have a 2008 F350 with a 6.4 Powerstroke diesel engine that just experienced total engine failure. It has around 65K miles.
There is a heavy burn star pattern on all 8 pistons, a few pistons are cracked, a few cylinder walls are scored, glow plugs are melted, both heads are cracked with multiple stress fractures in each head.
About 1 month previously, the transmission would not work in tow mode and caused the engine to go into limp home mode. The dealership just replaced the entire tranny as a warranty item. About 1 week before the engine failure, I put in a 5.25 oz bottle of Lucas injector cleaner with a full tank of gas.
The Ford dealership is saying that the star pattern on all 8 pistons is due to high pressure fuel overspray and is evidence that I had a tuner on this engine and that the warranty is invalid. I did not have a tuner. What might have caused this engine failure?
Also, they only ripped down the top half of the motor, not the bottom half. I heard this might have been caused by a cracked crank shaft, but Ford refuses to investigate this possibility.
06 Charger Won't Start Sometimes - Going Into Limp Mode
I have a 2006 Charger R/T. My car used to not start (even thought the battery, starter, and alternator was good). I had it fixed, and the problem seemed to be electrical. However after that, it would always start, but would go into "limp mode". I let it sit for two days, and the limp mode disappeared. However, it will only start on occasion. It won't start after about 30 mins after use. It won't start for a few hours. All electrics work fine, it just won't even attempt to crank. Try to start it later, it will work fine. Even though the check engine light was NOT on, I was able to pull three codes out of it: U0100, U0103, P0700. I did have to replace the notorious "pink thingy", but everything (should be) connected fine.
View 1 RepliesPhaeton :: 2004 V8 - Going Into Limp Mode
Happened once or twice where I tried to back up a hill and the car went into limp mode. Neither the dealer nor my mechanic could replicate it.
View 5 RepliesGolf VI R :: Limp Mode With APR Flash?
So I was driving kinda hard yesterday on the highway, and it was about 80 degrees outside. At some point in the drive, I got no boost from the turbo at all (my gauge also was showing no boost). I pulled over, stopped the car, and restarted it, and the car was back to normal. Is this something I should be worried about? I am running 93 program APR Stage 1+ with VWR intake and HPFP.
View 24 RepliesGolf IV R32 :: EPC Light Came On And Car Gone Into Limp Mode
So on cold mornings my r has been kicking on the epc light and gone to limp mode. The only codes are for the coolant temp sensor and an intermittent accelerator position sensor. Would the temp sensor really cause this? After awhile I can start it up and it runs fine.
View 7 RepliesSanta Fe (CM - 2007-12) :: Not Want To Start In P Mode On Automatic Gear Box
I have a Hyundai Santa Fe 2007. have recently had problems with the car not want to start in P mode on the automatic gear box.
It starts as usual in the N mode instead.
Looking for recognize the error, what could it be? A sensor, fuse, or what?
Malibu :: Code 2135 And Also Goes Into Limp Mode
My 2010 Malibu has been throwing a code 0f 2135 also goes into limp mode. Code comes up as throttle pos sen. So looking I can see it is all built in one with the throttle body. Can it be changed with out any special tools?
View 3 RepliesIS F (2008-2014) :: Car Went Into Limp Mode When Restarted
I have a 2008 ISF with a k&n intake and QTP exhaust cutouts. About a month ago my car died on me and when I restarted it, the car went into limp mode. The "check vsc" light is on along with the traction light and CEL. I took it to my mechanic and he said I needed to replace the MAF sensor and I did. 100 miles later the car went into limp mode again. So I took it to a mechanic that knows Lexus vehicles very well apparently, and he diagnosed it to be my intake. So he replaced it with the stock intake. Now I've driven another 100 miles and the problem has come back again. The car is throwing all kinds of codes when I connect the obd2 scanner to it.
It is throwing p0031, p0037, p0051, p0057, p0102, p1360, p1361, and a whole bunch more.