Ford - Explorer :: 1996 - Speedometer Mostly Always Reads 50 MPH
On my 96 explorer the speedo most always reads 50mph. It goes to this as soon as you take off. You can be doing 5mph or 75mph and the speedo goes to 50mph and stays there. Everything else on the instrument cluster works. Is there something I can replace on the speedo only or do i need to find a good used instrument cluster?
View 1 RepliesFord - Explorer :: 1996 - Speedometer Works For One Mile Or So In Mornings Only
1996 Sport Trac. Cruise control works. Speedometer works for one mile or so mornings only. New sending unit in transfer case. What's up?
View 2 RepliesFord - Explorer :: 1996 - Speedometer Goes Exactly To 50 And Stays There When Vehicle Gets Warm
My Explorer speedo works fine for the first bit of riving but when the vehicle gets warm it goes to exactly 50 and stays there.
View 3 RepliesCivic - Honda :: 1996 - Check Engine Light On And Speedometer Drops From 60 To 0
Driving on highway, check engine light goes on, speedometer drops from 60 to 0 but nothing else happens. Come to a stoplight and engine light stays on and speedometer works again. Any diagnostics?
View 1 RepliesFord - Explorer :: 1996 - Speedometer Jumpy And Odometer Quit Working / Shifts Hard
My speedometer is jumpy, odometer quit working at same time. Shifts kinda hard going into 2nd and 3rd gear. I am at wits end. I have replaced both speed sensors, checked all fuses, and also tore dash apart checking the worm gear in the cluster. I don't want to take to the ford dealer. The truck got 172,000 on it but been very well maintained. I just don't think its the transmission. Its got to be something easy.
View 9 RepliesFord - Explorer :: 1996 - OD Light Flashing And Speedometer Bouncing Around Not Detecting Current Speed
I just brought a 1996 Explorer 4x4 V6 XLT from a friend thinking it was an easy fix by answers I found of the problem on the net. Even search threw the threads here. Right now my OD light is flashing and the speedometer is bouncing around not detecting the current speed. Also it's not going into gears smoothly. I've replaced the VSS as well as the gear on the end of it. What was the fix for it?
View 4 RepliesFord - Ranger :: 1994 - Speedometer Not Working
My speedometer does not work. Also, my 4wd high light is on but not engaged. Are the two related? I've looked up speed sensor and it's separate from the actuator for 4wd. Maybe coincidence they stopped working simultaneously? Should I start with the speed sensor?
View 1 RepliesFord Ranger / B-Series :: ABS Light And Speedometer Not Working
I have the infamous ABS light & speedo not working on my 2000 Ranger. I replaced the ABS Speed sensor on the rear diff as has been suggested on many posts, but it didn't solve the problem. Did I get a bad part or is there something else I should go after?
View 7 RepliesFord Ranger / B-Series :: 1998 - Speedometer Not Working
so heres whats happening. My 98 ranger speedometer has not been working since I owned it (I am the second owner who got it from a grandpa) and I've replaced the vss sensor two times, got a new connector and gave that a try and still nothing. Yes I've looked for cracks in the wire or any exposed copper, I've looked through many forums and cant figure it out. At first before replacing the vss, my abs and check engine light weren't lit up until i put a new vss sensor on that i got from o'reillys, so then i got another one thinking it was just a bad sensor and still no luck. another thing is when its cold in the morning and i get in my pickup to go to work it will start working once i go over 30 and fluctuate between that and 20 but if i don't accelerate it will not bounce all over the place.
View 4 RepliesFord Ranger / B-Series :: 2000 - ABS Light Stays On / No Speedometer
I have a 2000 ford ranger 4.0L v6. My problem is the abs light stays on and the speedometer won't work till i hit about 35-40mph.
View 14 RepliesFord Ranger / B-Series :: Speedometer Bouncing - ABS Light On W/ RABS DTC 9 - Fix?
Last night the speedometer started acting up, would fluctuate when the truck went over bumps and completely cut out on moderate right turns. Looked underneath as well as one can in the dark and couldn't find anything loose.
This morning I searched on here and the VSS came up numerous times as a common failure. $15 and about a half hour later I had it installed, and while I was under there I took a better look at the other connectors to double check harness connections for tightness and cleanliness. It all looked good, so I went ignition on... and the light came back. Tried clearing it by keeping the diag connector unplugged while switching ignition off, but no go. Took it for a quick spin around the parking lot, and the speedo was completely dead.
Hit up my factory ETM, found all the relevant connectors and set up a wiggle test of the VSS circuit with the DVOM on audible continuity check. Found one of the wires had chafed against the body right by the under-cab harness connector and worn almost completely through. Cut out the bad bit, soldered and heat-shrunk a patch in, and took it for a spin. Voila! No more ABS light and a working speedometer.
Also fixed the fuel gauge sending unit wire which was in the same connector grouping and chafed (but not yet broken) in a similar manner.
Ford Ranger / B-Series :: 1990 2WD - Speedometer Stopped Working
I have '90 Ford Ranger 2wd standard cab long bed. A few days ago the speedo stopped working. What is the more likely cause? The gauge itself or a relay/cable. And if it is the cable/relay are they hard to remove & replace.
View 1 RepliesFord Ranger / B-Series :: Speedometer Will Reverse Despite Of Increasing Speed When Gets Over 75 MPH
1999 (built late 1998) Ranger 2.5 stick 2wd single cab. If I get much over 75 MPH the speedometer will reverse direction despite increasing speed. If I then let off the throttle completely, the speedo will jump right back up and indicate the correct speed. Continued operation without letting off the throttle to let the speedo recover will trip the ABS fault light, probably due to the erratic signal.
Disconnecting RABS module has no effect on symptoms. Speed sensor in the rear axle has been replaced already (by me) and the new unit ohm'd out good. Wiring between GEM and sensor checks out as well, good continuity (< 1 ohm) and no shorts to chassis ground. I wish I had an o'scope to take a look at the waveform, but I don't at the moment. It is on my future tool purchase list.
Ford - Ranger :: ABS Light Came On / Speedometer Quit Working And Trans Not Shifting Right
Recently the ABS light came on (truck does not have ABS), also speedometer quit working and trans was not shifting right. After a few minutes the problem went away.
View 4 RepliesFord - Ranger :: 2000 - Speedometer Quit / Jump When Brake Pedal Pressed?
I have a 2000 Ford Ranger, 5spd with 3.0 v6. The speedometer will jump around or quit about half the time whenever you push the brake pedal or use the turn signals. I've cleaned all the grounds I can find including taking the battery cables off the clamps and cleaning them, and I had to clean all the fuses (inside box and outside box) because most of them were corroded. It still does it. Occasionally, I'll hear a buzzing/crackling noise like electricity arcing when I use the brakes or the turn signals which sounds like it's coming from the left side of the dashboard.
I took off panels and the fuse box, but I don't see any sign of arcing. Also, the noise only occurs when the truck is actually moving, never when it's sitting still. Also, the engine has a slight flutter at an idle. I hooked up a computer, and the O2 sensors were erratically jumping between rich and lean, so I replaced all of them. It says Insufficient EGR flow detected, so I did put a new EGR valve on and cleared the codes, but it still reads the same. And lastly, the computer refuses to finish either of its diagnostic tests. I've tried the Koeo and the koer tests, and neither will complete.
Ford Ranger / B-Series :: 2000 - ABS Light / No Speedometer And Transmission Doesn't Want To Shift
Sold my mazda and got a nice 2000 2wd Ranger XLT with a 3.0L. Today the wife I and took it to town, 10 miles on the highway there, a couple in town and 10 back, didn't notice anything unusual. However I haven't this truck long so I'm not sure what is usual.
Parked it for a few hours and when went out to change the front turn signals to LED I noticed the ABS light was on when I drove it into the garage...
I checked fluid, connections and fuses, no change.I go ahead and swapped the bulbs while letting things simmer, I've had so many of these Fords sometimes the easy fix comes to me.
I backed it out and took it down the road, right away I noticed my speedometer wasn't working, so I let off the gas, when I re-applied the pedal I got nothing, like it was in neutral.
I downshifted to second and got her down and turned around as the O/D started flashing... (so glad because I would have hated walking back), then pulled her back in the garage to check transmission fluid and recheck fuses, including the ones I forgot earlier under the hood. I added a 1/4 qt of fluid then tried a road test again, this time there was a real long pause before it upshifted hard and the CEL came on.
I pulled the codes with my scangauge and got:
P0500
P2120
P0028
And decided I better look some things up and consult the gurus here before I do anymore damage tonight. I'm guessing that I'm looking at a tranny replacement possibly, but with the ABS light and speedometer failure I'm not 100% sure what is going on here...
Ford Ranger / B-Series :: No Speedometer / Odometer After Alternator Changed - Code P0500
1998 Ranger... I started having Speedometer/odometer problems after a power surge when my alternator went out. I knew the alternator was going bad and I tried to limp home another 5 miles rather than pay a tow bill and the alternator overcharged for a few seconds before completely dying. Since that time the only problem I am left with is my Speedometer and odometer have not worked. Scan tool says p0500 and I have replaced the ABS sensor on the differential with an OEM part but still no speedo or odo. I have checked all the fuses and relays associated multiple times. I do suspect that the RABS resistor is bad but there is no ABS light and it doesn't make sense that this one resisitor is the sle key for the whole speed control circuit. It's a manual transmission and RABS only. I swapped out the Cruise Control Servo with no luck as well. I am running out of options before having to take it to a dealer because I have to pass inspection. I have also checked and there is no power coming to 679 (GY/BK) into the instrument panel. I have also checked continuity for the rear harness to the ABS sensor and it is good.
View 2 RepliesFord Ranger / B-Series :: 1993 - Changed Speedometer Cable And Sensor Still Bouncing?
so i changed the speedo cable and speed sensor in my 93 ranger, but still getting the speedometer bounce. what could be next? the speedo housing in the cluster? lubed the inner cable, made sure nothing is kinked or sharp bends. Put in a new vehicle speed sensor while i was at it just bcuz. cruise control does not hold a steady speed either but i think the 2 are not related. I'm leaning towards the cruise control servo as to why it does not hold a steady speed. Most of the time once i get to around sixty i'm basically driving by ear bcuz the speedo bounces from 60down to 55 and back up.
View 3 RepliesFord Ranger / B-Series :: Speedometer Dial Started Climbing When Driving On Highway - Erratic Readings
On my '91 last week I was driving on the highway about 60-65 when all of a sudden the speedo dial started climbing to 70-75-80-85 and past. The odometer seems to be working ok? Still when I drive it still operates in the same manner. It never bounces around or falls back. The needle is sort of stable such if I maintain a speed the speedo will maintain even though it's incorrect. There is a slight wavering of the needle meaning it's not as stable as it use to be. With the odometer working I was wondering and don't know. Does the cable drive the needle or is it electrically controlled? I'm thinking of grabbing another instrument cluster it that is the problem, I'd like to know more about it and understand how it works so I don't just throw parts at it until it's fixed.
View 1 Replies