Golf IV R32 :: Cam Position Sensor / P0016 Code
I have a mk4 r32 with 110,000 miles and I'm throwing a p0016 code witch I believe is cam position sensor my timing chains and guides were changed at 90k car runs good and if I erase the code it doesn't come on right away maybe every 200-500 miles:confused could this just be a bad cam sensor there is also no oil leaking from them and they are tight.
View 14 RepliesNissan - Sentra :: Code P0335 For Crankshaft Position Sensor
I got a 2004 Nissan Sentra and a p0335 (Crankshaft Position Sensor) popped up on it after the car stalled out sitting in a parked position for 2 mins. The car also stalled out again 20 mins later while I was driving. When the car stalled out in park I had to wait 3 mins because it was just cranking over, when it stalled while driving it started 30 secs later with 1st turn of the key. This car has been having start up issues after the car been driven and sat for 40 mins but when the key is cycled 3 times it starts up fine. I also was going to eventually make a post of this, the car been making clicking or rattling noise at times, off and on mainly when the car been warmed up and at idle more noticeably heard , hear the noise better from inside the car, forgot what side of the engine where the noise is coming from. Also I did a search in the past about recalls on this car and there was a recall on the CRANK ANGLE SENSOR on the 2.5L engines, the car I have is a 1.8L. Stated on this link 3rd one down. [URL] ... . Does it sound like the Crankshaft Position Sensor needs to get replaced?
View 19 RepliesNissan - Altima :: MIL Came On / Code P0335 Crankshaft Position Sensor Circuit
My wife's 2003 Altima has been stalling. The MIL came on P0335 Crankshaft Position Sensor Circuit. I did a little research and it seems that it is pretty common for that sensor to go bad, so I bought a new one. The problem is I can't get the wires off the old one. It is in such a ridiculous place. There is no line of sight anywhere. It has to be done completely by feel. Supposedly, I should be able to push the button until it clicks and then remove the connector. When I push the button, it definitely clicks - but it doesn't stay clicked. It clicks right back out before I can pull on the connector. How can I keep that button clicked in when I can't see anything and I can just barely get one hand down in there?
View 19 RepliesCivic - Honda :: 2001 - PO335 Crankshaft Position Sensor A Circuit Error Code
33k Civic 2001 "PO335 Crankshaft Position Sensor A circuit" error code
My Civic 2001 LX (non vtec 1.7) threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining.
Civic - Honda :: 2001 - PO335 Crankshaft Position Sensor A Circuit Error Code
My Civic 2001 LX (non vtec 1.7) 33k threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining. So much for a reliable honda.
Aurora :: Crankshaft Position Sensors Replacement
Replacing the crankshaft position sensors on the 95-99 aurora? very difficult?
View 14 RepliesGolf IV / Jetta IV :: Crankshaft Position Sensor Is Wet With Oil?
2000 jetta vr6 manual 150k miles, i have trouble starting the engine so I thought i'd start by replacing the crankshaft sensor. I notice that its wet with oil when i pull it out, and wasn't sure if tits supposed to be dry. I may have a bad ECU in the end...
View 1 RepliesGolf IV / Jetta IV :: Won't Start - Bad Crankshaft Position Sensor?
My car doesn't start right now and a shop diagnosed it as an ecu, but I'm starting to think that is not the case. The tach doesn't move when I try to start it and pushing the gas doesn't change it, so I'm thinking it is the crankshaft position sensor. Unfortunately, down at school, I don't have access to a jack, so I was wondering if there is any way to get to the cpa without a jack? I'd rather not have it towed to another shop.
Also, my coil pack has a huge crack in it. Could that be causing my problem? And my sai has some really frayed wires and I'd rather not replace it if I don't have to because these repairs are really adding up, but could that be causing problems too? it's not causing gas mileage issues and I live in an emissions-free county, so simply not allowing me to pass emissions isn't a problem.
Santa FE SM (2001-06) :: Crankshaft Position Sensor Replacement
After heavy rain yesterday my 2005 2.7 Santa fe wouldn't start today. Had it towed to nearby dealer. The crankshaft position sensor needs to be replaced. He claims its melted to the block and oil pan needs to be dropped to remove it.
View 5 RepliesSonata I45 (YF - 2011+) :: Crankshaft Position Sensor Location?
Looking for a picture or description where this sensor is located? I assume very close to the crank pulley, but I'm hoping I will not need to remove the crank pulley to gain access to this sensor. I have a 2011 Sonata, 2.4L engine.
View 3 RepliesCaravan/Voyager :: 2002 - Crankshaft Position Sensor Replacement
I need to replace the crankshaft position sensor. On my 2002 Grand Caravan Sport 3.3liter. Where it is in laymans terms.
Is it better to approach from the underside Or from the hood side? I will know it when I see it but I haven't seen it yet!!
Silverado :: New Engine Won't Start - Crankshaft Position Sensor Is Out Of Circuit
I have a 2001 Chevy Silverado 4.3L that I recently put a new engine in. The new engine will turn over but will not start. I am not getting any spark for some reason. The OBD2 code that keeps coming up says that the crankshaft position sensor is out of circuit. I have put in a new CKP sensor and new electrical connector, new spark plugs and wires, new distributor rotor and new ignition coil and still get the same OBD2 code and it won't start.
View 2 RepliesSanta FE SM (2001-06) :: Crankshaft Position Sensor Broken In Block
2002 My friend's 2.7L sante fe crankshaft position sensor went bad and I went to replace it. Removed bolt, it was stuck fast, tried to pry out and it broke off leaving the last 1/2 inch stuck in block. Tried drilling a hole in it and using a screw to get it out but no luck. Afraid to keep drilling that I might damage something behind it. How to get it out?
View 9 RepliesJeep - Compass :: 2007 - Crankshaft Position Sensor Location
My son has a 2007 jeep compass 2.4l engine. He needs to change the crankshaft position sensor. Where to find it? He got a pic from autozone but you can't tell where it is on the engine.
View 7 RepliesSanta FE SM (2001-06) :: CEL Codes For Crankshaft Position Sensor - Random Misfires
I am having a problem with my 2003 Santa Fe I have taken it to have the check engine light codes read and I have a code for the crankshaft position sensor, random misfires, something with gear 2 and 3 (not sure what it was exactly) it makes a loud noise when in 1st and 2nd gear when I shift out of 2nd the noise gets less and less until its gone and then does not come back until the car sits for a little while and cools down. Its running rough and does not have any power when accelerating. I had the timing belt changed a few weeks ago and it started running funny shortly after. I don't think the guy that did the timing belt knew what he was doing because I had to have someone go behind him and tighten the pulley.
View 3 RepliesSaturn - Vue :: OBD Code - Car Is Giving P0016 And P0017
The car is giving me P0016 and P0017 codes. I have read up on them, and it appears 17 could point to 16 being the culprit. Regular service, oil changes when the car says it is time. Vehicle has 90k miles. This is the 4 cyl engine. So, what am I most likely looking at? One or both sensors? Basically, is there a common problem associated with this vehicle and these codes that I can begin looking at?
View 2 RepliesPassat (B6) :: Error Code P0016 After Oil Change
P0016 - Crankshaft Position | Camshaft Position Correlation
Bank 1 Sensor A
2006 Passat - 3.6L V6
Here is my issue: I was lazy and waited a bit too long to get my oil changed. I finally did 3 days ago. I have been very busy so I decided to take it to a local mechanic to let them take care of it. They flushed the oil, ran other oil through it with a new oil filter, flushed that, then put in new synthetic oil with another new oil filter. They also replaced the air filter.
Everything was fine for 2 days.
Then, while I was driving in stop and go traffic, the "EPC" and "Engine Malfunction" lights came on. There was also a loss of power and the car seems to wait too long to shift gears.
So, I took it back to the mechanic who had it a few days prior. He pulled the code from it (posted at the top), and cleared the code from the car. That mechanic told me that I need a "cam position indicator sensor". He also claimed that what he did had nothing to do with this issue. I decided to check with the dealer. He cleared the code and I left. After clearing the code, the car drove fine for most of that day, then it returned.
I spoke with the VW dealership's shop manager and he said that he does not believe that is the issue at all and asked me to bring it in. He also mentioned a clogged oil line as being the potential culprit.
Lexus RX 2004-09 :: Code P0016 After Timing Belt Change
After timing belt change code P0016 with Check engine light trac off and VSC light on.
Put on the entire kit...timing belt,tensioner, idler, and water pump. When I took it apart to put the new cam crank sensor I inspected everything and all looked good.
Changed the sensor and reset code, a few hours later back on. Car seems to run fine. I didn't think the sensor was bad. Car was running great...just due for timing belt.
TrailBlazer :: 2004 Extremely Rough Idle - Code P0016
My brother-in-law brought me his 2004 Trailblazer that had an extremely rough idle and would die if ya thought about the air conditioner and all! So he had replaced the cam sensor, didn't work. He replaced the spark plugs didn't work. He replaced the fuel filter didn't work. So he asked me about it and ran across a fella talking about the CAM ACTUATOR SOLENOID and explained all about what to look for and such and low and behold new solenoid later purrs like a new one!!! It is look right above the power steering pump there is a plug in the side of the engine there with electric wires running to it.
One of the signs of being bad is oil inside that 2 wire plug just pull it off and look in it. Now to remove it you will have to take the power steering pump loose so it will move back out of the way so you can pull the solenoid out of the engine if ya get it out look on the end there are grooves running around it with little screens on them see if any are gone or coming apart, this usually sets a P0016 code which is stuff interfering with the sensors inside. If there is any oil in the plug or any screens missing then it will have to be replaced.