Prius (2010-12) :: Change Reverse Beeping From Continuous To One Beep?
A couple months ago I bought a 2010 with the basic trim package. How to change the Beeping in reverse from continuous to "one beep". The owner's manual says that you have to take it to the dealer.
View 5 RepliesPrius (2010-12) :: Cannot Turn Off Reverse Beep?
The technician at Toyota showed me the options. You could either have a continuous beep or the intermittent beep, but you do not have the option of turning it off. I told him it was possible, but how?
View 19 RepliesPrius (2010-12) :: How To Disable Reverse Beep
Looking for the instructions for disabling the reverse beeping on a '11 prius?
View 2 RepliesPrius (2010-12) :: Way To Deactivate Continuous Beep When In Reverse?
If you are tired of that irritating continuous beep while in reverse, I can take care of that for you. I can customize your Gen 3 (2010-2015) prius to only beep once while you put your car in reverse. Process takes about 5 min and can be done anywhere. If you are around the Vacaville, Fairfield California area, we can meet up and I can customize your prius for you. Hit me up if interested.
View 5 RepliesPrius (Gen 3) :: Oil Pressure Reading On Scan Gauge II?
Can I read oil pressure on my scan gauge II ? If so, how do I do it?
View 14 RepliesGen 2 Prius :: Scan Gauge To Go Blank Every Minute Or So
My scan gauge has begun to go blank every minute or so. Any fix?
View 5 RepliesPrius (2004-09) :: Scan Gauge II Keep Going Blank
Scan gauge II keep going blank !
View 4 RepliesPrius (2010-12) :: Does Reverse Beep Go Back To Default Setting After Disconnecting Battery
I had the reverse and seat belt beeps changed by the dealer before I took delivery. Now I want to install some mods which would entail disconnecting the 12-volt battery. With pre-2010 Prii the beeps would go back to the default settings. Will this happen on the 2010+? I don't want to make another trip to the dealer.
View 10 RepliesPrius (Gen 2) :: All Dash Lights Lit Up And Scan Gauge Showing Code P0A93
I am about 50 miles from El Paso and 350-400 from home, broken down on hwy right now, all the dash lights lit up and my scan gauge says p0a93 the inverter pump thing. Nothing has been worked on or messed with so i should have no air in the lines etc
Can I drive it like this to El Paso or home? Car seems to be running fine. Car is under toyota warranty so i don't want to screw anything else up.
Prius C :: 2012 - Can Monitor Transmission Fluid Temp With Scan Gauge
I have 2012 Prius C, I want to monitor my transmission fluid temp with my scan gauge II. I watch the MG1 and MG2 temps, which can get very high, like 215 F. I hope this isn't the trans fluid temp as well.
View 5 RepliesPrius (2004-09) :: Check Engine Light On And Scan Gauge Indicated Code P0000
Purchased a used 2005 Prius with 30,000 on the clock. Have put 5,000 miles on the car with no problems. Recently the check engine light came on and my Scan Gauge indicated a trouble code of "P0000". Cleared the code and four days and 500 miles later the check engine light returned with the same code. Car runs great even with the light on. Have check the fuel cap which was and is tight.
View 2 RepliesPrius (Gen 2) :: Turning Off Beep While In Reverse
Cannot any instructions of how to do it. there are a few links that are supposed to tell you, but those links did not lead me to any instructions.
View 8 RepliesPrius C :: Beep In Cabin When In Reverse?
New noise maker means they turned off that "cabin" beep nonsense when in "R"? With our ZVW30, the ONLY indication that the last of the gas is gone is the 'power flow' arrows disappear. I'm wondering if Toyota might have brought back something to let the driver know the last of the gas is gone.
View 10 RepliesPrius V :: Turn Off Beep When Reverse Selected?
Is there a way to disable the beep when reverse is selected?
View 19 RepliesFord 6.0L Power Stroke Diesel :: Scan Gauge Just Went Blank
My ScanGauge just went blank, which was nuisance because I like to monitor it in the mountain climbs. It felt like a 'naked' dash without it. My separate pyrometer was the only additional info I had. The ScanGauge only has a few thousand miles on it. Wondering how reliable these things are before considering getting another, or inquiring about a fix I know I will first have to double check that the OBII port is still OK, but I expect it is.
View 11 RepliesFord 6.0L Power Stroke Diesel :: PID To Monitor MAF With Scan Gauge II?
I have googled for this and searched the typical sites but cannot find the PID to monitor the MAF with my scan gauge II. Am I blind or does it even exist?
View 1 RepliesPrius (Gen 3) :: Unable To Disable Reverse Beep Using Bluetooth OBDII?
I picked up a bluetooth OBDII scanner and plugged it up, and tried following the instructions found on this forum. Only problem is, every time I run 3b ac 40, I just get a return of NO DATA.
View 2 RepliesFord 6.0L Power Stroke Diesel :: Scan Gauge II - How To Show Coolant Temps
I'm trying to chase down a couple of issues and I need to be able to monitor the coolant (and oil) temps. I've downloaded the manual and the specific 6.0 X Gauge commands but don't see the coolant temps listed.
View 8 RepliesFord 6.0L Power Stroke Diesel :: Engine Off Scan Gauge Shows 14.4lbs
2005 f350 6.0, parked in my shop and the batteries were dead after 2 weeks on vacation, (I left a few items plugged into 12vdc ports charging) charged it up and started right up. Next day cruising down the road about 75 the wrench icon showed up, strange. I reviewed my scan gauge and only thing not correct was my boost, it was 20lbs plus, idles at 14lbs. dash gauge appears normal.
Next morning I turned on the key, turned on my scan gauge engine is not running and the reading show 14.4lbs on my scan gauge. so..... adding the 14.4 to the scan gauge reading thru the drive cycle. so my computer thinks it is seeing 20-30 boost during acceleration. A bad sensor......... but don't know which one.