Prius (2004-09) :: Grinding Noise Coming From The Front
I've got a 2004...it has 90,000 miles. For about the last 5000 miles I've been experiencing - only a few times a month, and totally out of the blue - a grinding noise coming from the front (i think left). This happens when I'm traveling at about 55-58 mph (never at lower speeds). It even happened once when the cruise was set. It gets pretty loud, and i find that if i pull over and stop for a few seconds, then keep going, that it stops. In other words, it seems that breaking to a stop disengages whatever the cause is. Also, no warning lights come on at all...like i said, it happens totally out of the blue. No, it's not the wheel bearing.
View 6 RepliesChevrolet - Venture :: 2004 - Front End Grinding Noise
I have an 04 Chevy Venture. Recently it started making what I can only describe as a grinding. I have been a mechanic for over 30 years, working on everything from motorcycles to heavy construction equipment. This is a new one on me. I have checked the wheel bearings, brakes and rotors, and suspension. All good. I have blocked her up and put it in gear, and the noise seems to be coming from the transaxle. Fluid is cherry red and is not burnt, no metal shavings, and not low. I have noticed that while driving, if I jog the wheel left or right, it quite until you straighten out again. If I weave back n forth going down the road, it's pretty much non existant, but the cops are starting get suspicious.
View 6 RepliesPrius (2010-12) :: Grinding Noise Near The Front Axle
So I was driving yesterday and I hear a grinding noise near the front axle. I pull over and a plastic panel is hanging off near the front of the car. I go to the family mechanic to have him put it back on, and since one of the clips are missing, he tells me to go to the dealer to get a clip and have them fasten the panel.
This morning I go to the dealership. The service advisor gets me right on a lift and comes back about 20 minutes later with a slip of paper. He tells me that the piece is the door from the under body plastic protection that protects the oil reservoir. There are no sides of it that seem to have been ripped off a larger piece, just holes to be screwed in. He tells me the whole entire piece needs to be replaced, end of story. He did not offer warranty coverage (I have 20K on the car) and was not interested in speaking to me further on the topic. The parts desk pulled up a diagram of the car and showed me the panel as part of one big piece underneath that needs to be replaced.
I am going to seek out another dealership on this, but I wanted to pose this to you all as well. First, do I even need to replace this small piece of thin plastic? Second, if I do, can I buy just this small piece and not the entire under body panel. I noticed some threads about the poor design of the oil door, and perhaps this is what this is? I do not have access to a floor jack or garage, so all of my service (free toyota care) has been done at this specific dealership. Here is a pic of the piece.
Toyota - Corolla :: 2004 - Slight Grinding Noise From Front Right
I have an '04 Corolla with 206k with a slight grinding noise from the right front when I make a left turn. Is it the outer CV joint? The noise sounds like the tire is rubbing against a splash guard but it's not.
View 3 RepliesPrius (Gen 3) :: Grinding Noise From Front End When Applied Brakes At U Turn
Coming to a left turn signal I was anticipating it turning red on me, and I drove into the turn lane briskly 30mph and then applied brakes as I made a u-turn. It sounded like a cross between dragging the front air dam and metal on metal brake grinding as I made the turn. Stopped immediately and did not scrap the air dam and all front end components checked out, okay. Car is driving just fine now, has only done this once.
View 18 RepliesFord - Focus :: 2004 - Grinding Noise From Front Passenger Side
I've had a grinding noise coming from the front passenger side, sounds like the wheel area of the car, for many months. I've driven thousands of miles on it like this, mostly because I'm broke and the car otherwise runs fine, but also because when I've taken it to mechanics, they are stumped.
I took it to a shop about a year ago and he had it for a week, had different specialists look at it and ruled out anything mechanical (wheel bearing, etc.) In the end, he threw up his hands and didn't want to give me any more free labor for his non-diagnosis, and thought he ruled out everything but the transmission. I took it to a transmission shop recently, and the guy ruled out right away that it was the transmission. He tried to diagnose the problem and was stumped too.
Here's what it is doing. It makes a grinding noise around the front passenger wheel when I accelerate. Only when I accelerate. It seems to be more active when it is cold, and after I've been driving the car for about an hour or so, it goes away. It used to only really happen when taking right-hand turns, and that is still when it is at its worst, but now it does it anytime. However--some days it is very bad and some days very light. One day--of course the day I designated to take it to the shop--it stopped altogether and drove like new. Just until I got it home. It is worse in low gears, and used to only happen in first, second and third, but now on an active day I can hear it on the interstate in fifth gear.
The shops I've taken it to can't seem to figure out what it is. Reading threads online, I've learned that people with similar problems found the problem was a bad passenger side motor mount. I have the car at a new shop right now, and I asked them to replace the motor mount, even though it looks fine. I had a long talk with the mechanic there today and he seemed a bit skeptical, but thought it was a possible solution.
Should I spend the money on a motor mount even if it looks okay? (I've also read that the Focus mounts look fine from the exterior when they are bad because they have a gel interior that busts). Especially if this doesn't work, I'm going to be back at square... um, zero.
Ford F-150 (2004-2008) :: Grinding Noise From Front Passenger Side
2005 ford f150 Fx4 So last Friday I started hearing a grinding noise from the passenger side front of my truck. sounded like metal on metal. So I started rooting around and noticed that bottom ball joints were shot. so replaced bottom ball joints on both side. I aslo replaced wheel bearing hub assembly on both sides, still heard the grinding. So I noticed that both axles were slinging grease, so I replaced them on both sides.
Still heard the grinding noise. So then I removed everything from the passenger side and noticed that the locking hub actuator was grinding both axle and the wheel bearing hub. So I just got done replacing that on the passenger side, put it all back together, and still grinding noise ringtones free. Also replaced the 4wd solenoid that they said gets water in it, and I replaced the check valve. And I put new Rotors and breaks. What it could be?
Ford F-150 (2004-2008) :: 2006 - Grinding Noise On Both Sides In Front End
I just bought 2006 f150 4wd . It make a grinding sound on both sides in the front end..it seems to be independent and when I slow and come to a stop, I makes a clanking noise like its locking something in.
View 4 RepliesFord F-150 (2004-2008) :: Grinding Noise Coming From Front Wheels
I have an intermittent grinding noise coming from what sounds like both front wheels, it sounds like metal on metal almost like something metal rubbing the rotor but I just put new pads on and the noise was there before as well with nothing touching the rotors but the pads. The sound will appear out of no-where at low speeds of 35 or below and will continue until I brake and slow down, just before I come to a compete stop the noise will stop with a slight clunk.
I can then drive away with no noise. I am pretty sure it is not brake related except maybe ABS somehow but was also thinking front axle or diff, also have read posts that are bearing related, but both at the same time?. It is the slight clunk before stopping that I can not figure out is related to. It is an 05 f150 xlt 5.4 super cab 4wd with 85k miles
Ford 6.7L Power Stroke Diesel :: 2004 F250 - Grinding Noise From Front End
Ok here goes. I recently replaced the front wheel hub and upper and lower ball joints on the the driver side of my 2004 f250 CC SB 6.0 fx4. Now when I put into 4 wheel drive I get a grinding noise that sounds like a worn out break pad from that side only. It didn't do it before and it only happens in 4x4. I have replaced the wheel hubs before and it was fine. Also The needle bearing race on the axle is good.
View 2 RepliesFord F-150 (2004-2008) :: While Turning Makes Rubbing / Grinding Noise From Front?
I've got a new issue that is happening on the front end of my truck. Whenever I try turning my wheel while driving, I get this rubbing/grinding noise coming from the front of my truck. It only happens when the wheels are in motion. It seems to happen less when I'm driving at higher speeds, but I can notice it make the sound at any speed. I tried driving it slowly in an empty parking lot while turning and it's definitely making the sound every time the tires rotate.
I took it in for an alignment because this was happening every time I drove, whether it be driving straight or making a turn. Now that my alignment has been fixed, it no longer make this noise if I am driving in a straight line, so it only seems to happen when I'm turning. I had the mechanic check to see if they could reproduce the issue. The mechanic was able to hear what I hear, but when he put it on the lift at the shop, he was not able to reproduce the sound.
Ford F-150 (2004-2008) :: 2006 - Grinding Or Whirring Noise Coming From Front Passenger Side Wheel
I owned a 99 f250 a little while ago. Just bought a 2006 crewcab F150 xlt about 2 months ago, and for the past month there has been this unusual grinding or whirring like noise coming from the front passenger side wheel.
I took it to the mechanic and he found a bad wheel bearing on drivers side and replaced it but that wasn't the issue. He could hear the noise but wasn't able to figure out what the actual issue was.
The noise only happens when my foot is on the throttle. (not when coasting) and i also just discovered that it doesn't make any noise at all when put in 4x4.
Prius (2004-09) :: Red Triangle And Grinding Noise
Basically I have two problems which will be looked at by Toyota on Friday. But I need to arm myself with ammunition in case I have a debate with the service/repair guy.
Firstly my gen 2 decided not to start for about 10 minutes and gave me the red triangle with an exclamation mark before everything went back to normal again. The car starts every time now but the triangle appears briefly at the start which I don't think was there before. Could this be the 12V battery?
Another thing is grinding noise on full lock to both left and right. What could this be?
Ford Super Duty (1999-2016) :: 2004 F250 4X4 - Front End Rumble - Squeaking / Grinding Noise Then Clunking
So to start at the beginning.... Traveled across Canada East to West towing 11000lb travel trailer, no problem. Have used 4x4 in a few campsites to pull out of a pitch without spinning the wheels and causing damage to the site when it has been really wet. All good.
Got to Banff in December and the town was an Ice rink, engaged 4x4 and all good. Crossed the Rockies and the 4x4 starts making grinding noises. Up and down some mountains and squeaking, grinding noise then clunking.
I have manual hubs, disengage and the noise all goes away. Engage 1 hub and no noise. Engage both hubs, noise back.
I bought some needle bearings and went to swap them. Got hubs apart and they look good. No scoring on the drive shafts. They are not dry, but as I have them open, repack them with grease anyway.
Do more research... Remove ABS sensor and repack main bearings with grease. (broke one sensor pulling it out, too cold plastic brittle oops). Still clunking noises.
The universal joints look good, doesn't appear to be any play in them. However, the axle seal (knuckle seal) (F81Z-3254-CB) does move around a lot in it's metal casing. It is tight on the shaft, but with the hub off, I can move it in and out, and move it side to side. If I had ESOF hubs I guess they would not be locking as I'm sure there would be no vacuum in there!
Question is then, would this seal be allowing the universal joint to wobble under load in 4x4 mode? Would this wobble be the cause of the rumble? As it is labelled as a seal and not a bearing, I wouldn't of thought this would have been a loaded point, and the weight would have been taken by the associated bearings and it could be run without this seal? But if it is not this, then I'm still looking for a clue as to what is making the rumble....
Prius (2004-09) :: Grinding Noise When Braking At Low Speed
Bought my Prius (2005, with 160K miles) about a month ago and since I've had it I am hearing a metal on metal grinding noise when braking at low speed. How loud the sound is depends on how hard I am on pushing on the brakes. One of my co-workers has the same model and said that his does not make that sound. Not sure if its just because it has after-market brake pads or something? This noise only occurs when braking at low speeds (below 10 MPH) so I assume its an issue with the front brakes.
Is this something I need to get looked at by the dealership? I had a local mechanic that worked on my old Honda beater take a look and he said that the rotors and brake pads looked new and wasn't sure why they'd make noise.
Prius (2004-09) :: 2007 - Grinding Noise When Braking
So my dealer diagnosed my 2007 Prius with a transaxle issue, but what bothers me is that it doesn't make the sound all the time. When I brake lightly, there is no sound and when I brake heavily there isn't either. It is only when I do a medium brake above 7 mph of course and around 20's mph range. I am hoping for something besides the transaxle...maybe a wheel bearing...anything.
View 19 RepliesPrius (2004-09) :: Whirring / Grinding Noise In Dash
I am experiencing this whirring/grinding noise:
Which is the same as this thread : Grinding Noise from Dash | PriusChat
It occurs intermittently when starting up the car, though if I then turn the car off (as in my video) the noise continues.
On that thread the vehicle was in warranty and was fixed by replacing the MFD touchscreen. My 2006 UK Prius is (I believe) out of warranty, and the touchscreen/MFD seems to be working fine. Is there anything I can do preventative on this?
Prius (2004-09) :: Grinding Noise On Radio While Braking / Accelerate
I may be worrying over nothing but lately when I brake or accelerate I hear a grinding noise on my radio. I listen to AM. With my other vehicle it usually meant there was a problem somewhere.
View 1 RepliesPrius (2004-09) :: Inverter Generator Grinding Noise When Braking Above 7 Mph?
My car was making a weird grinding noise when braking above 7mph. I did the neutral brake thing and seems to go away sometimes. The dealership said it needed new rotors and brakes, so I went ahead and did that with them, then called me to let me know the sound did not go away. Now they are stating my grinding noise is coming from the "inverter generator" which is what they said was the transmission. I am just curious why this goes away sometimes and if it's related to my previous issues with the car.
View 1 Replies