Passat (B6) :: CEL On / Code P0299 - How To Replace The Diverter Valve
The CEL on my Passat came on. When I scanned it with VAG-COM, the following fault code was displayed:
000665 - Boost Pressure Regulation
P0299 - 002 - Control Range Not Reached
The car also felt like it lost its power in some way, especially when the turbo kicked in. So after some research, I found out that the Diverter Valve was causing this issue. Rubber diaphragm on original valve was made from rubber and was torn. I replaced it with upgraded valve and wow what a difference!!! Very easy to do, great write up link below.
DIY Diverter Valve Replacement for 2006 VW Passat 2.0T
Golf IV R32 :: How To Replace Secondary Radiator Hose
Realized I was leaking coolant from the front passenger wheel well and bumper area. If I fill up the expansion tank it'll almost empty in about 2 days of sitting. Took to the stealership for a quick diagnostic and they said my Intercooler...(Auxilary Radiator) was leaking at the hose connections and will need to be replaced as well as the hose. I can't find a good DIY on this at all and I'm not sure which hose is connected to the Aux Radiator. So I'm wondering which hose connects to the Aux Radiator? Is there anything else I should replace or look for while I'm at it? Which hoses connect to this Second Radiator?
View 2 RepliesFord Ranger / B-Series :: 1989 - Heater Hose Leaking Around Behind The Valve Cover
Found a tee on the heater hose leaks when it warms up. Appears the PO had noticed it but put a hose over it and now is leaking around behind the valve cover. This is a hard plastic line around 5/16. No online parts show it as being available. Is there a fix for this ?
I would bet several others have had this problem as it lays right on top of the flange of the valve cover where I think it would rub a hole pretty quick.
1989 Ranger 4X4 4 cylinder....
Ford Excursion :: Leaking Coolant Hose Under Degas Bottle Behind Valve Cover?
My truck has a 6 o powerstroke. I noticed some coolant loss, which I've been monitoring since I had the truck studded 2 years ago. Today I was looking around trying to find a cause of the coolant loss and I noticed some crusty orange residue on a hose that runs under the coolant reservoir. The hose seems to go behind the valve covers along the firewall to the passenger side through a steel line, and then go in a loop back to itself?
I'm guessing it's for the heater core, but I didn't see where it actually goes into the heater core, or anything else for that matter. It is a molded hose that has one of those crimped transitions into the steel line, so I'm not sure if patching it is an option or if I should look at replacing the whole piece. I'm guessing it's going to be expensive. From the fact that it never failed before, I'm thinking it wasn't originally routed with it touching the valve cover and was just something that happened after having the body off during the stud install.
Elantra XD (2001-06) :: Can't Replace PCV Valve
I've replaced clutches, brakes, timing belts, water pumps, radiators, etc, etc. My 2003 Elantra has 65,000 miles on it and a few years ago I tried to replace the PCV valve with no luck. The PCV valve is threaded into a copper/metal ring that is pressure fitted into the valve cover. When I tried to remove the PCV valve the copper/metal ring spun thus not allowing me to unscrew the PCV valve out of the copper/metal ring. Now when I try to unscrew the PCV valve the copper/metal ring spins in the plastic. I can't get the PCV valve out to replace it.
View 8 RepliesFord Super Duty (1999-2016) :: Cannot Find Hose For Canister Pressure Valve?
I can't find canister pressure valve hose. It looks cut from the pressure valve in some way. Tried following it from gas tank but I've lost it through the chassis.
View 4 RepliesJeep - Cherokee :: 2006 - How To Replace EGR Valve
How do you replace egr valve?
View 4 RepliesSuburban :: 2001 - Error Code Replace EGR Valve
Have 2001 suburban with the 5.3. Mechanic has replaced EGR valve 3Xs. Error code specifies "replace EGR valve". Each time car runs fine for 4-6 weeks (500-1000 miles) and then service engine light comes on. Shortly thereafter the car will not idle correctly (under 1,000 rpm) and will die at stop. I think the EGR valves are getting clogged up with carbon. Car has 130,000 miles on it.
View 4 RepliesCamry :: Possible To Replace A/C Expansion Valve Without Tearing Apart The Dash?
I am looking at replacing my A/C compressor but in order to keep the warranty on the new compressor it states that I have to replace the expansion valve (and desiccant). My current compressor hasn't eaten itself yet so I am fairly confident that the expansion valve is still good. However, being a $30 part, I have no problem replacing it if it is fairly easy to access. According to the maintenance manual it is not as it instructs to literally rip apart the whole dash. I just wanted to know if any way to access it without doing all of that work?
View 4 RepliesMitsubishi - Suspension - Diamante :: Should Replace Valve Cover Gasket?
Two mechanics have told me that I need the valve cover gasket in my car replaced. I have all of the classic signs of needing one--the smoke coming from under the hood, the drops of oil on the pavement after the car is parked for a few minutes, etc. The problem is that I won't have the money until around Memorial Day. I drive about 300 miles a week. How desperate a repair is this, and what are the signs that I need to have it fixed immediately?
View 5 RepliesCamry :: 2002 - Valve Cover Gasket Leaking - Replace?
I have a 2002 toyota camry xle 6 cyl i believe i have a valve cover gasket leaking vehicle has 112,000 miles. is there a step by step removal proccess i can access. I have done one on a 1995 honda passport 6 cyl how difficult is it
View 2 RepliesSubaru - Legacy :: Replace Transmission Valve Body Assembly Code
I started my Subbie and all the lights just start going crazy on my dash. So I pulled of the road and started freaking out, Never had a hint of a problem. So I pulled in AutoZone and they ran the codes and now I'm being told I have to replace the brain to my transmission WTH? I don't own a DODGE!!! Had 3 different dodges and the tranny went on all. So I wont own one because of transmission problems. Now my Subaru has been parked since it can only get worse. Is this normal? All the error codes are...
P0700 Transaxle Control System (MIL Request)
P2762 Torque Converter Clutch Pressure Control Solenoid Control Circuit Range/Performance
Ford - Explorer :: 2002 - Replace Valve Spring - Remove Engine?
Thats what my mechanic told me about my 2002 exploder sport trac with 4.0. I started another thread here a while back about my truck having a bad miss, turns out it has a broken valve spring. He said the engine must be removed to do the job as its on the #1 cylinder which happens to be on the passenger side and the cam chain drive is on the back of the block.
He said my choices are: Remove the engine and just replace the spring, which may or may not effect a repair as theres no way to know if the valve made contact with the piston. Remove the head and send it off to a machine shop for repair/inspection. Or, remove both the heads, one for repair and inspection, the other just for inspection, and then put the whole mess back together.
Whats the best option here? I'm not exactly made of money, and, I'm still licking my wounds about having such a mechanical disaster take place on a vehicle that up until this point, I absolutely loved and has only 90,000 miles on the clock.
Ford 6.0L Power Stroke Diesel :: 2004 F250 - Replace Or Clean EGR Valve?
My '04 F250 6.0L has 220k on it. I've had the EGR serviced several times and, unfortunately, the intake manifold boiled out in one of those services.
The engine light is on now and I've got "EGR Performance Problems" just below 2000RPM most of the time but not all of the time (runs better when warmed up)
I've been unemployed for quite sometime so I'm going to have to make this fix myself.
First question, of course, is should I plan to clean or replace the valve?
The second is how to clean the manifold chambers (? right word? The carbon accessible when the EGR is removed. I've seen people on YouTube scraping them with what looks like brake tools. Is there an appropriate tool or chemical?
The third question is is it going to be very difficult removing an EGR valve that may have carbon buildup on it? Too difficult for an aging seldom mechanic to think about tackling?
I guess those are good starter questions. I didn't know until today that EGR cooler may also be part of the problem. Unlike many of the people who post here, I have not kept good repair records. I don't know when I last had my EGR valve replaced at the Ford dealership but it was probably 50,000 miles ago.
Mercedes-benz - C-class :: C240 Car Seems To Be Gasping For Breath And Attempt To Stall When Come To A Stop
Mercedes Benz C240 ... Every time I come to a stop, the car seems to be gasping for breath and attempt to want to stall. Occasionally the battery/alternator light comes up. It has not stalled yet and seems to catch its breath and continues once I step on the gas after the shake and after there was an air rush through the vents (I called-Caching its breath). I took it in to the dealer and the electrical was checked and they found nothing.
View 6 RepliesFord F-150 (2009-2014) :: 2013 FX4 - How To Remove Right Side Valve Cover To Replace Gasket
I have a 2013 FX4 with the 3.5 twin turbo engine. How to remove the right side valve cover to replace the gasket? I have loosened the perimeter bolts and was able to get it to move slightly but nothing more. I also removed the spark plugs thinking that they might be holding the tubes which are connected to the valve cover by round seals. I have not removed the seals since I was concerned that I might damage them. Do they need to come off? If so how do I do it? It's amazing how complicated this job is! Short of calling the dealer service, I have just about exhausted all my usual tech resources.
View 4 RepliesAcura - Cl :: 1998 - Poor Heat Distribution / Check Antifreeze Coolant Or Replace Heater Control Valve
I just bought a used 98 Acura 3.0CL. I've noticed that when the heat is cranked, it doesn't blow hot at all. I did some quick research and came up with two answers thus far; check the antifreeze coolant and that I may need to replace the heater control valve. Am I "warm" on the area?
View 19 RepliesPassat (B5) :: Cracked Hose On Intake
I have a CEL. I don't have any special tools or experience but am not afraid to try something.
View 8 RepliesPassat (B5) :: How To Remove Clamp Around Hose
How to remove clamp around hose? I am in process of changing out reservior tank. Ignore post. I got it, was afraid they were the one-time use only type of clamps. But duh, they are the spring clamps.
View 1 Replies