Passat (B6) :: 3.6L Engine Is Idling A Bit Rough
Just noticed the other day the Passat was idling significantly rougher than usual, most of the time it's smooth as butter but not so much lately. It's not rough like a bad misfire, just not very smooth anymore. This could be indicative of the dreaded oil-pump bolt failure rearing it's ugly head (finally)?
View 1 RepliesPassat (B6) :: Check Engine Light / Rough Idling When Stopped
Weird problem on my Passat today. First the engine light came on...followed by rough idling. It smooths out when moving, but rough again when stopped. Noticed that turning ON the AC makes it a little smoother...but when you turn off the AC, resumes the rough idle.
Already made an appt with the dealer tomorrow...but wanted to see if this problem is familiar to other owners. Either way, I will update once the dealer finishes diagnosing the problem.
The car has been perfect up to 30k miles...now 2 problems in the last month.
IS F (2008-2014) :: Rough Idling And RPM Fluctuations While Cruising
Check engine and tcs light came on solid. Rough idling and rpm fluctuations while cruising. Brought it to toyota and they scanned it revealing a P2195 code: bank 1 air fuel sensor stuck lean. So what I'd like to know is; How long was the vehicle in the shop? What is involved in repairing this problem?
View 10 RepliesFord F-150 (2004-2008) :: Knocking When Idling Very Rough
My truck is idling terribly and knocks while doing so, little info is
The truck has 170k miles, I just bought it about two months ago and it was running perfect, drove it to the beach two or three times (4 hour drive) no problems whatsoever. Two weeks ago I noticed it start rocking a bit at idle ONLY when warm, check engine light came on so I ran the code and it said the Cam shaft positioning sensor was bad so I replaced both of those, then the next code I got was for the vct solenoids, replaced both of those and the problem is still persisting. It is odd to me in the fact that when its cold, it runs flawlessly, no problem accelerating/idling/maintaining speed/smoke nothing at all.
As soon as it gets warm it will still do everything flawlessly EXCEPT idle. the idle rpm is around 300-400 and it rocks and knocks terribly.. If i am stopped and I apply some throttle in park or nuetral, just enough to get the rpm up to around 800-900, its perfectly fine. no more rocking no more knocking but as soon as i let my foot off the gas it goes right back to feeling like its going to fly out from underneath the hood.
So my question is why is this? What on earth is going on here? and how do I fix it? And why is there not a manual idle control. Ford place said there was likely damage to the head and recommended a full engine replacement.
Ford F-150 (2004-2008) :: 2007 - Idling Rough And Stumbling A Bit
I have a 2007 F-150. Here is the story....
Last summer the truck was idling rough and seemed to be stumbling a bit. Took it to the dealership and had it diagnosed. Had a mis-fire code on cylinders 1 and 3. I was told to do the spark plugs and clean the MAF. After replacing all plugs and cleaning the MAF the truck seemed to run better but it didnt last long before it started doing the same thing. My Edge Evolution started showing misfire codes in cylinders 1 and 3 again and the truck is stumbling like crazy. Here is what i have done:
1. Swapped the plugs from cyl. 1 and 3 with cyl. 5 and 7 and the problem followed.
2. I replaced the bad plugs with new ones and i no longer get a code for those cylinders but the truck is still acting the same.
Now I am getting two codes saying the system is running rich on bank 1 and 2 and a misfire code in cylinder 4. I cleaned the K&N filter and replaced the MAF but it is still the same. The truck stumbles horribly under a load and has NO power.
History:
2007 F-150 5.4L Lariat
75K miles +/-
K&N Filter
Edge Evolution (has been kept in stock mode)
new spark plugs last summer
new MAF (this week)
New Fuel filter (two summers ago)
Santa Fe (CM - 2007-12) :: 2008 - Cylinder 3 Misfire / Vehicle Is Idling Rough
I have a cylinder 3 misfire and the vehicle is idling rough so I took it to the deal because I have a power terrain warranty. They're telling me I'll need a new manifold and plenum, coil pack, plugs, and gasket. Could this be accurate? I don't want to get screwed over...
View 9 RepliesPassat (B5) :: 1999 1.8T - Running Rough When Idling, But Only In Drive?
I just got my first dub, and it is a project car. I have had it serviced and it still idles rough when in drive with foot on the brake but idles normal when in park. a
View 2 RepliesFord F-150 (2004-2008) :: 2006 5.4L Idling Very Rough And Had A Terrible Miss Around 1200 RPM
I have a 2005 5.4 F-150. First off it came to me on a rollback because the owner tried to replace his plugs after he noticed it missing and of course broke one off. So after I extracted the plug from #8 cylinder and installed a new plug I cranked the truck and it was idling very rough and had a terrible miss around 1200rpm. I pulled the codes and got several misfire codes and ignition coil faults on #5,6 and 7 cylinder. Popped in 3 known good coils in these 3 cylinders with no difference.
On Mode 6 on my diagnostic software you could watch the misfire count steadily increase on #7 and every now and then there would be a single misfire on #5 and 6. It also had several codes for O2 sensors biased, stuck rich on that bank. Well since it had a brand new plug and coil, I popped an injector in #7 and havent had a single misfire on it since and it also started idling alot better and all the O2 codes went away. The problem I am having now is #5, 6 and now 8 will randomly misfire, sometimes build up a steady count on one of them, sometimes just skip around between them.
The truck has brand new plugs in all 8 and new coils on this bank also. The truck has 115,000 on it and does have some cam phaser noise on the bank causing the problem, but its not too terribly bad, I have heard alot worse. My problem is something on that bank only as the passenger side bank is fine. I am wanting to say cam phaser now since this is the side with the noise. I have changed them before but have just experienced the noise, never one running like this because of it. Possibly jumped time a little?
Passat (B5) :: 2003 VW GLS 1.8T - Rough Start / Idling And Misfiring On One Of Cylinder?
I haven't started my passat for the winter and I finally did today. It was ruff start/idling and I pretty sure it was misfiring on one of the cylinders. I turned off the car and start it again...same thing, ruff idling like 3 cylinders were running. I waited five 5 mins and started it again, then it was a normal start on all cylinders. But the engine light came on, even though it started properly. I know I have to clear the code to get rid of the engine light. But I want to avoid any future misfiring. So I'm thinking new spark plug/coil overs.
View 9 RepliesPassat (B6) :: Idling Is Little Rough - 3 Codes P0011 / P2293 And P000A
Only thing I've noticed is the idling is a little rough but the car has 88k on it so that's expected. I haven't checked the cam follower yet and know I'll probably need to change it so that's going to happen in the next week.
I had a code for P000A & P2293 for a few months that would throw a MIL and I would reset it and it would come back after a while. I finally replaced the cam sensor and I didn't see a MIlL for about 6 weeks and one day it came back. Once I scanned the car it showed P000A again. I cleared the code and everything seemed fine until yesterday. I went to start the car and the car wouldn't turn over.
I pulled the key out and tried it again and it worked. More and more I think about it, the car doesn't turn over smoothly over the past few months but maybe I'm just looking for things. I ended up scanning it last night and it had a code for P2293 & P0011. I cleared them both but what could be causing all this and cannot afford to bring the car in to the mechanic. It's out of warranty and I'm broke and X-Mas is around the corner.
2006 Passat 2.0T
Ford F-150 (2004-2008) :: 2006 - Rough Idling When Warm And Dying At Stops Or In Reverse
My brother's 5.4 has been rough idling and dying at stops and in reverse for a few weeks now. Today it threw a code and he finally had me look at it and it's a P0345 code. I was thinking cam phasers possibly, but I didn't think that would cause a code to throw. Also, all I hear about cam phasers is that it makes the truck sound like a diesel, but his when it's about to die sounds like the engine is about to drop out the bottom of the engine bay. Really rough, REALLY loud knocking, etc... What we should be looking at replacing to get this thing back into shape?
View 3 RepliesPassat (B5) :: Valves Rattling When Startup On Cold Mornings / Idling Rough
Ok, I have owned my 02 Passat with the 30V 2.8L V6 since may. I got it with 115K and now its just under 129K I had the timing belt done at Jimmy's in Provo UT at 126K and up until then the engine ran great. Since the belt was replaced <along with the water pump and such> . The car has a tendency to feel like its idling rough, and when you start it up first thing on a cold morning it sounds like the valves are rattling. It does this for a brief second then goes away until the next time you start it in the cold morning. It wont do this if its warm outside, or after you start it previously that day. So far I have replaced the plugs with Bosch Platinum 2 prong plugs, and replaced the fuel pump. I replaced the fuel pump when it dead on me without warning about 2 months ago.
View 1 RepliesGolf/GTI VI :: Engine Idling Very Rough With EPC Light On
I was just at work tonight and went out and started my car for it to warm up (it is -20) and go back inside for about 15 mins, I come out and as I am walking back to my car. I notice tons of exhaust is blowing out from the bank puffing like a steam engine and idling insanely rough with the RPM gauge at about 900 RPM with a EPC code. I immediately shut off the car. Cautiously turn the car back on. Car is idling normally, EPC code is gone, rev it a bit. Everything seems fine.
View 20 RepliesFord F-150 (2004-2008) :: 2007 XLT Won't Start - Random Rough Idling Spell Or Stall Going Down The Road
I have a 2007 F150 XLT, Supercab 6.5' bed, 4x4 5.4 Automatic with 67000 miles on it. Its not a Flex Fuel
Over the past couple of weeks it would get go through random rough idling spell or stall going down the road. If it was sitting it would idle clear down to 200 RPM's and just sound like an old 'chitty-chitty-bang-bang' car, not a modern marvel of Ford engineering!
I noticed it particularly does it this on an incline. Initially I fixed it by just coasting to where it was flat. I normally keep it above half a tank so i dont think its a fuel pump not getting fed. So I replaced the fuel filter yesterday hoping it was full or clogged, no changed.
This morning it would start at all, I removed the negative terminal on the battery, rolled to the level, tried it 30 times. Nothing. I checked all of my connectors under the hood and the 2 below the cab under the plastic cover. Everything was connected. I disconnected the fuel pressure sensor and it fired right up and runs smoother than since I've owned it.
It hasn't had any CEL lights, until I disconnected that sensor. Should I drop the tank and clean it? Is there any special gasket kits or connectors I should be aware of? Should I just replace that sensor? Is it connected with a chain of sensors I should check first?
Camry :: Rough Idling Engine On 2002 Toyota SE
Our '02 Toyota Camry with 92,000 miles has been idling rough for awhile. I tried cleaning the throttle body which actually seemed like it made it worse for awhile. I do need to replace the valve cover gasket and I don't think the spark plugs have ever been replaced. Is that a good place to start?
View 6 RepliesTiguan :: Engine Idling Really Rough Then RPMs Will Spike
It could happen once a month or 3 times a day. No pattern and never the first time I start my car for the day. But I will be running errands, park the tiguan, run into a store for 5, 15 or 30 minutes and when I get back in my car and start it up and go, it dies when shifting from 1st to 2nd. I know how to drive stick. This doesn't happen every time. I have called/taken it to the dealer 5 times and they have no clue because it never happens with them and I cannot predict when it will happen again. Also, on occasions, when i start my car, halfway through the day, the engine will idle really rough then the RPM's will spike and the car gives itself gas and my foot is definitely on the brake. These little issues are starting to piss me off, especially since the dealer just shrugs its shoulders.
View 12 RepliesPrius (2004-09) :: Engine Will Not Stop Idling And Idles Rough
Just picked up my 2004 Prius from the Toyota dealer body shop. The driver's side was scraped by someone who wanted to be in my lane. Fortunately, we were only going 35 mph. The rear door skin had to be replaced, and most of the side had to be prepped and painted. There are a few silly mistakes: they forgot to replace the driver's door plug, forgot to replace a lower clip, and smudged a tiny area new paint on the bumper. I brought that to their attention and they are going to take care of it... they have to order the plug and clip.
However, as soon as that conversation was complete, it was time for them to close shop. I sat in my Prius, started it, and the check engine light was on. Wasn't on when I dropped it off for the repairs. Also, on the way home, I noticed the engine wasn't turning off when I came to a complete stop (even though the animation says it was off). At idle, the engine is also rough. Looked at the charge bars, and well, there were only two bars showing.
I thought perhaps, though it's not done this before without the animation screen showing it, the engine was on merely to recharge the traction battery. On the way home, the traction battery returned to full charge (green), but the engine still was not turning off when the vehicle was at a complete stop... not was it turning off when coasting... and when arriving home, even with the car in park... and still idling rough. All the while, the animation on the screen is indicating the engine should be off.
When I replaced the traction battery three years ago, I also replaced the 12v with an yellow top Optima. I wouldn't think the Optima is already going bad. I also do not believe in coincidence. I wonder if perhaps some bad fumes have tainted the MAF, or who knows.
Mazda :: Check Engine Light Blinking And Idling Rough Almost Cutting Out
Today I went to the gas station and after I gased up and turned the car on my car started idling rough, almost to the point of cutting out. I started out on the road and my check engine light started blinking. After some time it stopped and just stayed on. The whole front end shakes pretty bad when at idle. The car has trouble accelerating till roughly 35-40 mph then seems to ride ok. I'm not very car knowledgeable, but I do take care of my car. I know I need to replace some of my hoses and spark plugs soon, but am worried that it may be more serious.
What I would like to know is: 1. What could possibly cause these issues and 2.
2003 Mazda Protege
Accent MC (2006-11) :: Engine Was Idling / Little Rough And P0302 Code Thrown
So I bought my accent used a couple months ago. It is a 2007 SE 3dr 5spd manual. It ran nice during my test drive and the price was right so I bought it.
Now I'm wondering if there is any way to find out the service history on the car...at least the major one's (30k, 60k)?
I ask because recently the engine was idling a little rough and it threw a P0302 code so I changed the spark plugs and holy-cruddy-deposits-batman those things were black. Gapped the new ones and popped them in and its a noticeable difference. My CEL keeps coming on and throwing a P0496 code as well, virtually once every tank of gas. Its not the gas cap so my next step there is to check the PCSV and hoses.
With these little problems, it makes me wonder about any larger issues. I know the timing belt on these things is supposed to be replaced at 60k. Additionally I would be willing to bet that my ECM software is out of date. Would Hyundai have records for any of the big maintenance milestones since they are required for warranty work?
How much does it cost to have a dealer check your ECM software and update it if needed?