Subaru - Forester :: 2006 Idling Roughly And 2nd Cylinder Was Misfiring
I have 2006 Subaru Forester that is idling roughly. 90k – oil change every 3k miles. Per diagnostic codes I learned that the 2nd cylinder was misfiring. I replaced the coil, spark plugs, ignition wires, and an airflow sensor. Yet, my car still idles rough. The check engine light is solid and the cruise control is flashing. The idling problem only happens when stopped… after I get high rpms there is no shaking. I had someone disconnect the battery and reset the computer and the lights stayed off for about a week and idling was fine. Week later – the problem returned. I think this an electrical problem, but not sure if mechanical.
View 19 RepliesAccent MC (2006-11) :: Cylinder 2 And 4 Misfiring Causing Car To Shake While Idling Or Speeding Up
Recently my car, after I put fuel into my car, my car won't start unless I apply the gas and then shift it into gear. I thought that perhaps replacing my spark plugs would fix this problem since it is about time for a tune up on my 2010 Hyundai Accent. About a week after changing the spark plugs I now have an error code that states that Cylinder 2 and 4 are misfiring and it is causing my car to shake while it is idling or speeding up. Also it is much slower than before to get it started from a stopped position.
View 11 RepliesCivic - Honda :: Rough Startup - Oxygen Sensor Gone Bad / Each And Every Cylinder Misfiring
This is a 2003 honda civic with about 150k on it. Recently the check engine light came on so I went to Advance auto parts to get my codes read. I got back that the oxygen sensor had gone bad and each and every cylinder was misfiring?
What could be causing the each cylinder to misfire like that? I drive it about 60mi every day and it doesn't seem to drive all that rough. So it's kinda weird that it said every cylinder was misfiring, like how could I even drive it like that?
I heard the oxygen sensor is something I don't have to worry too much about. I could still drive it. The clerk told me to some spray carburetor cleaner on it and that should do something for it.
But recently I've noticed that it starts up rough, seems to strain for about 2-3 seconds then it starts.
Gmc - Sierra1500 :: 2007 - Truck Started To Ride Rough / Cylinder 6 Misfiring
2007 GMC Sierra 1500 (MAX) ... This had happened before 3x, but was about to turn truck off and wait 10 second and turn back on. Then truck would run fine for months. I found this on my truck manual.
My truck is riding differently. Here's the story - I put new tires on Friday, an hour later, my truck started to ride rough. The light on dashboard is; Check engine, Engine power lost (truck would not get up when this was shown on dash. This error has not come up again), stibilitrac check. Truck's driving performance; Idle sputters (like RPM rising, but they are not, it’s just the engine shaking), once driving when it shifts hard at 3000 RPMs (only 2nd gear). I took my truck to Advance, and this was the error code I received; #6 Cylinder Misfiring and Actuator module.
I changed all spark plugs and number #6 was very dirty compared to the other and smelt very much so like gas. I have not driven this truck only cracked and it stayed in park. I had a person look at it, and he said that the #6 cylinder was the only problem he could find when he hooked up his code thingy. Now he played with everything and took out the #6 spark plug (this is now Tues) and said that it didn't smell of gas like it should have. At the end. he stated that we first should change the Injector for #6. and if that did not correct the problem, then he would recommend the lifters to be replaced. I asked how confident he was about "his" diagnosis. and he stated.... I am not a GM mechanic... wow. now I am confused as to what I should really do! BTW, he never cleared the error codes...
Passat (B5) :: 2003 1.8T - Misfiring At Start Up
A friend of mine has an intermittent misfiring problem with his 2003 Passat 1.8T (manual). It occurs mainly at start-up when the engine is cold, and also sometimes at idle. After some research, we've found out that coil packs were a recurrent problem on some B5's, so my friend wants to take a chance and replace the coils.
View 2 RepliesCamry :: 2005 LE 2.4 - Engine Runs Rough / Loud While Driving And Cylinder Misfiring
I bought a 2005 Camry LE 2.4 4 cylinder. It was rather loud while driving, but especially while accelerating. It had error code P0420 from the beginning. It had a completely broken torque strut which I eventually replaced. Afterward since it toned down the kicking from the engine, I was able to notice that I could feel and hear the engine kicking like a cylinder misfiring. The computer gave me error code P0353 (Ignition Coil C Primary/Secondary Circuit Malfunction) consistently, and only a couple of times gave me error code P0500 (Vehicle Speed Sensor Malfunction) which went away.
I swapped the ignition coil and spark plugs around but the error code would persist on the same cylinder. The spark plugs didn't look particularly worn but I'm not experienced on what bad plugs look like. The codes persisted still, but later on P0353 went away, and the obvious kicking stopped but it still ran with a lack of power and hesitating on acceleration along with a strong smell of fuel in the exhaust. I measured the resistance of each fuel injector and all measured the same. I removed and flushed each of them with cleaner, but same situation.
What do you think? I don't get the bad cylinder code anymore but something is clearly wrong. Bad fuel injector? Bad wiring harness? Bad compression or head gasket (maybe from the movement of the engine while the torque strut was bad)? Hopefully not the computer... And could the loud noise be related to this problem or is that probably just a cracked exhaust from when the torque strut was allowing engine movement?
Ford Ranger / B-Series :: 2002 - Rough Idle Codes / Cylinder 2 And 3 Misfiring
I have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 RepliesPassat (B6) :: 2006 2.0T - CEL On And Cylinder 3 Misfiring
My dad has 2006 passat 2.0T. In December 2010 he went overseas. During his absence the car was parked in garage and not in use.
So one day I decided to start the car and as soon as I turned it on the car made this noise and check engine light came on. Took the car to a private repair shop and found out the cylinder #3 was misfiring. The tune up for this car was due so I had all four spark plugs changed and the car ran fine for few days. Then couple of days later it started making the same sound and this time around the coil for cylinder #3 was replaced.
A few days after that check engine light came back and this time it was blinking and the engine was struggling to run, took it again to the workshop yesterday and this time another coil not sure which cylinder was replaced. (all this is done at a private workshop). I have a hunch that the car is going to run fine for a day or so and the problem is going to come back
I never had any major issues with it up until now. Bought this car new in 2006 from dealer. I am afraid that this might be a start of a downhill roll from here on I will drive the car tomorrow and see how it reacts.
Passat (B5) :: 1999 - Misfiring At Cylinder 3
I've done just about everything me or my mechanic cannot figure out why cylinder #3 is misfiring has new plugs coilpacks checked wires etc. I love this car and will not put it to sleep!!
View 2 RepliesCamry :: 2003 With 4 Cylinder - Rough Idle Only At Cold Start
I have a 2003 Camry 4 cylinder. The problem we are having is the car has a slight rough idle only at cold start. After she warms up she is smooth as glass. What would cause this?
View 14 RepliesFord F-150 - 1997-2003 :: 1999 V8 Will Not Start / Truck Started Idling Very Rough And Died
1999 Ford F-150 V8 5.4L... The other day I was attempting to fix my 4wd. I discovered that the vacuum tube by the 4wd solenoid had become disconnected. I reconnected it and in an effort to see if my fix was successful, I drove my truck up one of the canyons nearby. I got to an area full of loose rock and popped my truck into 4wd. As soon as I began to drive, the truck started idling very rough and died. I attempted to restart it for the next few minutes unsuccessfully. I got it started once and it continued to idle rough for a few seconds and died. I have not been able to start it since. It turns over but will not crank. It is not throwing any error codes. What I have checked so far:
Spark plugs are working.
When turning the ignition into the ON position, I am able to hear the fuel pump working.
I have not seen any cracks in the vacuum hose.
All the fuses are still okay.
What the culprit may be?
Accent MC (2006-11) :: 2009 - Idling Rough / Cylinder 2 To 4 Misfire
So recently my 2009 hyundai accent has been idling rough, and has been very sluggish when accelerating. Usually the rough idling is the worst when the car is first turned on and tends to tone down as the car keeps running. I had the codes red and I believe it was C0302 C0303 C0304, saying that cylinders 2-4 were misfiring.
I replaced the spark plugs which didn't fix the problem, although cylinder 4 did have a small amount of oil above the spark plug and a little bit more below the spark plug, I am not sure if that means anything useful or not. I don't have a way to check the coils directly but I swapped coil 2 with coil 1 and checked the codes again and it was still cylinders 2-4 misfiring, so I would imagine that means the coil isn't the problem. I then tried spraying WD-40 around the vacuum tubes, and if the intake manifold is on the back of the engine I tried spraying it around that gasket as well, but I didn't notice a change in the idle speed.
At this point I am not entirely sure how to proceed, from what I have read the issue causing a misfire would be either there isn't a spark, which seems unlikely at this point, or the mixture of fuel to air is wrong. That is the part I am unsure of how to diagnose/
Ford F-150 - 1997-2003 :: Rough Idle At Start For About 30 Seconds - Cylinder 1 Misfire
2000 5.4l lariat. My cylinder 1 for 2 years has been poping p0301code and has a rough idle at start for about 30 seconds. It also has a little white smoke for that 30seconds. new cop, new spark plug, new spark plug pig tail, swapped injectors to different cylinders multiple times to change code no luck. Compression dry and wet are at 200 and all cylinders are within10%. I had a dorman intake manifold installed 4 years ago and the code came a few years after. Im thinking intake manifold gasket is bad between cylinder 1 and the heater bypass tube allowing coolant to slowly leak down into the cylinder causing my rough start. I looked through the injector hole but could not tell. With all the info I have given is there any other places or things that it could be before I do a gasket replacement or is all my tests leading to the intake manifold gasket...
View 5 RepliesSanta Fe (CM - 2007-12) :: 2008 - Cylinder 3 Misfire / Vehicle Is Idling Rough
I have a cylinder 3 misfire and the vehicle is idling rough so I took it to the deal because I have a power terrain warranty. They're telling me I'll need a new manifold and plenum, coil pack, plugs, and gasket. Could this be accurate? I don't want to get screwed over...
View 9 RepliesFord F-150 - 1997-2003 :: Misfiring Cylinder 3 And 8
Trucks throwing codes for cylinder 3 and 8 misfire. I pulled the plugs and both were covered in oil and cylinder 8s electrode was literally gone. so I replaced the plugs and within 5 miles it was missing again. so I replaced all plugs, all wires and coil packs. cylinder 8 plug had fouled out. Its a 4.6l 99. I have a mild exhaust leak where the manifold connects to the downpipe. but not bad enough I feel it should matter. it runs rough until about 3k rpm and then it kinda straightens out.
View 14 RepliesJeep - Liberty :: Idling Rough With No Error Codes - Multiple Cylinder Misfire
ODB2 Code: P0300 - Multiple Miss-fire
I have an issue with my Jeep Liberty. It started idling rough with no error codes. about a week later it through the Multiple misfire code. I started by replacing the spark plugs. The old ones were from 20K miles ago and still looked good. Replaced them anyway. I still had the code. I put K44 fuel injector cleaner into the tank and drove it home (2 miles.) The next morning I started it and went in side because I had forgotten something. I came out to extremely thick black smoke. It went away after about 2 minutes, the computer code cleared, and the engine idled perfectly. About 2000 miles later the car is once again idling poorly. I added K44 again and for that tank of gas it ran fine, no code. Once new gas was added it threw the same error code and idles very roughly.
So here are some basic info pieces:
1. 8 tanks of gas from 8 different locations.
2. Adding K44 has shown a direct improvement both times, but more significant the 1st time.
3. New spark plugs
4. New coil packs
5. 2005 Jeep Liberty - 3.7L V6 at 99,872 miles
6. Hopefully unrelated is that the car has a small radiator fluid leak I haven't found. It requires 1/2 gallon every 2K miles or so.
There is no knocking sound, it just sounds like there isn't enough gas. Car responds fine to accelerator. Above 10mph car seems to drive smoothly.
Passat - Volkswagen :: Misfiring On Cylinder 3 - Carbon Build Up On Intake Manifold
I recently took my 2007 VW Passat 2.0T in b/c the check engine light was on. They initially replaced a leaking valve and a bad ignition coil, but the car was still misfiring on cylinder 3. They took off the intake manifold and found that there was significant carbon build up. The service writer said it was from "low-quality" gas. The car requires 91 octane. I've used 93 octane since 2007 but started using 89 octane around 6 months ago when the gas prices spiked again. Could 6 months of 89 octane cause significant carbon build up to the point it would trip the check engine light? Or could something else have caused it that I need to watch out for?
View 4 RepliesDodge - Stratus :: 2003 - Misfiring - Faulty Cylinder 1
I am having issues with my everyday driver as of late. I developed a misfire and replaced, plugs, coils, plug wires. Misfire persisted so we replaced, injectors, fuel rail. The misfire still was there and getting worse so we checked the engine mechanically for any burnt or bent valves and it checked out fine. We completed a compression test and all cylinders tested within 5 psi of each other. We finally replaced the ECU and Cam Sensor and the problem still is here. We do not know what else to do. I have narrowed down the misfire to cylinder one. The injector is not firing on this cylinder. I know this because when you unplug it there is no change in the engines behavior. As stated earlier, injectors are new, but i switched them out just to make sure it was a bad injector. I tested the lead and the voltage was appriopiate.
View 2 RepliesHyundai - Sonata :: 2003 - Ignition Woes - Cylinder 1 Misfiring
I am driving a 4 cylinder 2003 Hyundai Sonata just at 130000 miles. The other day on the trip back home the car started shaking violently and the check engine light came on. I ran the code and it led me to a cylinder 1 misfire. Today I replaced my spark plugs, and wires. The number 1 plug had some deposits on it, but nothing that should cause a misfire.
Now when the car is in idle there is a spark that jumps from the boot of one of the new wires to the grounding on the corresponding coil. I have never noticed this spark before changing the plugs and wires. It does this with either set of wires. I have a picture below where the spark is jumping from. The car has a noticeable drop in idle when it sparks. Do I need to look into getting some new coils?