Prius (2004-09) :: Transmission Lock Error Message Only Reappears When Slow Down To 3 Mph
I've read around the forums stating the P Lock error is common from a low battery causing the vehicle not to start.
The strange thing is that my vehicle DOES start and the message appears and the dash shows READY and I am able to enter gear and drive. If I hit a button on the console the message goes away and if I'm driving at higher speeds the message does not return but the large triangle stays. The error message only reappears when I slow down to 3 mph.
The error does flash back on the screen when I slow down to stop or sit at a light. The car does not shut off during this it just flashes the message and shows the large triangle.
My battery test shows 12.3v on no load and 11.6 on a load. I would hate to replace my battery and have the issue not be resolved.
Avalon 2005-12 :: CEL Error Code P0440 Error Code / Charcoal Canister Replacement
So of course it has to happen 3 weeks after my warranty expires. My CEL comes on and I have it read and the result is P0440. I find out that my wife has a habit of topping off the gas tank and so I am thinking that she has probably ruined the charcoal canister. It is something easy to replace?
I have an 06 limited edition... Yes, she will not be topping off any gas tank anymore.
Passat (B5) :: CEL And Error Code P1476
I have this error code on my VW 1999 passat 1.8T automatic car. How to resolve it. My friend reset it and CEL went off for few days and now it came back again. How to resolve it??
View 2 RepliesPassat (B5) :: Getting Error Code 0012?
It happened to passat. Once I hit about 75mph on highway I get a stop engine (oil presser low light). It flashes than goes off once I lower my speed. I checked all fluids are normal. It throws a 12 code an says oil passage blocked, cam positioning sensor, skipped timing chain. These are what the code says could be wrong with it. The car runs fine with no hesitation at idle or normal city driving. I have already flushed the oil with cleaner, and still getting the light.
View 5 RepliesPassat (B5) :: OBD-II P1818 Error Code - Faulty TCM?
I was able to borrow an OBD-II scanner to read the error code(P1818) currently displayed. I was wondering if the P1818 Error Code is related to a faulty Transmission Control Module (TCM).
View 1 RepliesPassat (B5) :: Pulled Over Error Code P0741
My cousin's B5 wagon automatic 1.8T ('00) was shaking and vibrating intermittently. I took it down to Autozone and borrowed an OBD2 scanner. This is what it said (only one code, and the CL was off, although it comes on intermittently):
P0741 - Torque Converter Performance or Stuck Off
Passat (B5) :: Error Code P0491 Detected
The CEL tripped yesterday and this is the code autozone pulled. WHat does it mean.
View 3 RepliesPassat (B5) :: 2000 - CEL Came On - Getting Error Code P1176?
Check engine light is on... Then about 2 mins into driving Emissions Workshop comes across the dash.. i Ran the code it says
P1176 Oxygen sensor correction limit attained (bank 1)
What exactly does that mean in other words. also what is bank 1? im not sure what oxygen sensor it is out of the 4 of them.
i have a 2000 30v 4motion.
Passat (B6) :: Error Code P0016 After Oil Change
P0016 - Crankshaft Position | Camshaft Position Correlation
Bank 1 Sensor A
2006 Passat - 3.6L V6
Here is my issue: I was lazy and waited a bit too long to get my oil changed. I finally did 3 days ago. I have been very busy so I decided to take it to a local mechanic to let them take care of it. They flushed the oil, ran other oil through it with a new oil filter, flushed that, then put in new synthetic oil with another new oil filter. They also replaced the air filter.
Everything was fine for 2 days.
Then, while I was driving in stop and go traffic, the "EPC" and "Engine Malfunction" lights came on. There was also a loss of power and the car seems to wait too long to shift gears.
So, I took it back to the mechanic who had it a few days prior. He pulled the code from it (posted at the top), and cleared the code from the car. That mechanic told me that I need a "cam position indicator sensor". He also claimed that what he did had nothing to do with this issue. I decided to check with the dealer. He cleared the code and I left. After clearing the code, the car drove fine for most of that day, then it returned.
I spoke with the VW dealership's shop manager and he said that he does not believe that is the issue at all and asked me to bring it in. He also mentioned a clogged oil line as being the potential culprit.
Passat (B5) :: Whistle When Accelerating / Error Code P0411
I have this whistling noise that developed after re installing my stock airbox. Seems to have just started right after installation. Cant seem to pinpoint what is going on. I also had a error code come u p(p0411). 1.8t b5.5 passat ...
View 2 RepliesPassat (B5) :: 1998 - Error Code P0411 / Misfire On Cylinders 1 And 3
So i got a 98 passat sedan used and was told it read a p0411 code. The person at autozone told him it was a cam sensor. The sensor was replaced. I know now from the manual that codes reads for sec. Air injection system , incorrect flow. It could be the vacuum lines. Now lets say it is the vacuum lines. Their is a misfire on cylinders 1-3.
View 4 RepliesPassat (B5) :: Misfire Detected - Error Code P0322 And P0302
I bought my first VW about 3 months ago (so excited!) It's a 2003 Passat, 5 spd, 1.8t. I've had one thing happen so far (until yesterday). On 4 separate occasions when I'd go to start it, it would crank for a few seconds before it would start. Then once it was running the EPC light would turn on. It seemed to be running normally but I turned it off and restarted it and it started normally and the light extinguished (the first three times). The last time (about a week and a half ago) it kept doing it each time I started it, and upon starting probably the 4th time in a row the MIL came on. I drove it about a mile, turned it off for a few minutes, then turned it back on and it started normally with no malfunction lights on. It's been normal since then. Until yesterday...
Yesterday as I'm accelerating from a stop light (I think I was in 3rd) all of the sudden the engine started running really rough and the MIL came on. I turned around and drove about 2 miles back to where I started at about 20mph. The MIL would be steady while coasting and flash while pressing the accelerator. I got a hold of a diagnostic computer and it came up with 3 codes...
1) P0322 Ignition/Dist Engine Speed Input Circuit No Signal
2) P0302 Cylinder 2 Misfire Detected
3) P0302 Cylinder 2 Misfire Detected PENDING
Passat (B5) :: Check Engine Light Came On - Read Error Code?
2003 1.8t passat wagon. 50k miles... The check engine light came on today. Oil and engine temp are fine. Can most shops plug in and diagnose? Can I get one of those code readers at Advanced Auto parts to read the error code?
View 5 RepliesPassat (B6) :: Check Engine Light On (Error Code 4608)
What is the meaning or the fault concerning 4608. The above error code was reported on the computer diagnose machine and it referred me to look into the vehicle ownership manual book BUT its rather unfortunate that i could not find that book. So, what to tackle or replace on the engine to enable the check engine lite go off.
View 17 RepliesPassat (B6) :: Engine Error Code P2181 / Coolant System
If I am not mistaken this error code means that I have a coolant system issue. I've checked both of my radiator fans and they both spin, so it makes me think that its the thermostat issue. If I am correct, any link to a replacement part? Or better yet a DIY? I've searched and no dice.
View 12 RepliesPassat (B6) :: 2007 - Error Code Of P0171 System Too Lean
I have an 07 passat with a 2.0 4 cyl turbo and I have an error code of P0171 system too lean (bank1) but engine seems to run just fine, what this code means, am wondering if it is something I can fix or if it needs to go to the shop??
View 2 RepliesPassat (B5) :: Check Engine Light - P0118 Error Code
I got a P0118 error code on my car. Looked up some things and most people were saying change coolant temperature sensor. I changed it 2 days ago and have not had a chance to clear the CEL. Its still on now, guy at Autozone would not clear it, said it was against company policy.
Will this turn off automatically once problem corrects itself? I went to Autozone and had them rescan the error, this time another code poped up P0444, EVAP(Evaporative Emission System)Evaporative Emission Control System Purge Control Valve Circuit Open. What this can be?
Passat (B5) :: Getting Error Code P3081 - Coolant Temp Sensor?
P3081. What the hell is this code. I think it is a coolant temp. sensor issue.
View 3 RepliesPassat (B5) :: 2001 - Getting Error Code P0343 While Using Scan Tool?
2001.5 1.8t, I have this p0343 code when I used the scan tool at murrays or oreileys whatever the h they are now (it means something like cam angle sensor high input). The t-belt was due for service a while ago , am I looking at a sensor problem or a wiring problem or a timing/engine problem? How should I check and where? I hear the timing belt can be a pain on the 1.8s, I have done a mk4 trans and a bit of other stuff but I do have a lot going on right at the moment and I'm not sure if I have time. I have a feeling if I take it in for service they will probably find blow through from the turbo and pull the engine because of "sludge".
View 2 Replies