GTI 337/20th Anniversary :: Rough Idle - Car Get Close To Stalling When Falling From High RPMs

Just checking in to see where you'd recommend to start looking for a rough idle issue. It seems to get worse once the car fully warms up. I took a vid, and although it may not seem horrible in the video, it sometimes causes throttle lag from a stop and causes the car to get close to stalling when falling from high RPM's. Take a look at the video .....

View 2 Replies

Mazda - Tribute :: Stalling Out When Come To A Stop

I am a proud owner of a 06 Mazda tribute 3.0, 6 cylinder, 2 wheel drive, automatic. That is not the problem. The problem is on long drive 100 miles or more when we take a pit stop, to stretch our legs, we exit and when we come to a stop the suv stalls out. Its like we are driving a manual and forgot to push in the clutch. We can start it right back up and when we put it in drive it does it again. If we start it in neutral it will ideal but as we shift to drive it stalls out. We are not seeing any other problems. The MPG are the same and haven't gotten any worse. What should I look into fixing?

View 11 Replies

Audi A4 :: 1997 Stalling - When Started Up And Left To Idle All Of A Sudden RPMs Drop

I have a 1997 Audi A4 that has been acting a little bit strange lately. When it is started up and left to idle all of a sudden the RPMs drop from around 600-800 to 100-200 sometimes rebounding back up and sometimes the car just dies. This also is happening while I am driving and stopped at a stop light for a short time. It will idle fine then suddenly drop RPMs and if I don't give it any gas then the car usually dies. I have just had some work done on it to try and fix this problem thinking it was the air flow sensor (or something like that) but apparently that is not the case.

View 2 Replies

Mazda - Tribute :: RPMs Rise A Bit When Heat Turned On

I have a 2003 Mazda Tribute that seems to have a bit of an idling issue. When my heat on my car is off, everything is fine as far as the idle speed. When I have the heat on, even when it is low, and I am stopped, the rpm's rise a bit, then go back down to normal idling speed. The car also gives a little jump when I come to a stop. I think all of this is related to turning the heat on and off, as it doesn't happen when the heat is on.

View 11 Replies

Stalling - Mazda - Mazda6 :: 2006 - Run Rough And Idle At 1000 RPM?

I have a 2005 Mazda 6. When it is cold - I start the vehicle & begin to drive. When I slow down and the RPMS get around 1000 - the car begins to run really rough & try to stall. If I put my foot on the gas - I can usually prevent it from stalling. The problem disappears once the car gets warm. The dealership recalibrated the PCM based on a Mazda Alert. However, it has not corrected the issue. Looking for thoughts on what could be causing this?

View 5 Replies

Camry :: Rough Idle - Vibration Start As Soon As RPMs Drop A Little

I've made posts about a rough idle before now I noticed something new about it. I noticed when I approach a red light the vibrations don't start immediately. They start as soon as the RPMS would drop a little. They stay above 500 but it seems like it's below 750. As if the engine is slightly starved from power? Now i'm wondering if it could be related to another problem I have.

Whenever I start the car, the battery light flickers until the car is started all the way. This is on a 2007 Camry 4 cylinder. So far everything iv'e done is: New NGK Spark Plugs, NEW OEM mounts (all 4) Seafoamed the engine, Seafoamed the throttle body, cleaned the MAF sensor, New air filter, and cleaned the air filter box, replaced the PCV Vlave, new belt, new alternator (duralast), and a new battery (from autozone).

View 2 Replies

Subaru - SVX :: Rough Idle / RPMs Drop Very Low And Engine Shuts Off

1997 Subaru SVX (Alcyone) LSi, 3.3L H6 engine.

My SVX was driven from Denver to Las Vegas, NV and it developed an odd habit where the RPMs would start to oscillate while on cruise control. I had to disengage the cruise control to get the oscillations to stop. Three days later I was driving the SVX to work and the RPMs started oscillating at idle and the car started running rough and it died.

These things have all been replaced with OEM grade parts: Spark plugs, electric fuel pump & strainer & fuel filter, Mass Air Flow sensor, new air filter and fuses.

The car starts up fine but after a few seconds the RPMs begin to oscillate. Then the car tries to recover, the idle becomes rough, and the the RPMs drop very low and the engine shuts off.

View 2 Replies

Integra :: 1987 Rough Idle / When Stopped RPMs Drop Below Normal

I have done everything I can think of to this car. New; plugs, wires, distributor, battery, fuel pump, fuel filter, relay, and electrical lines to fuel pump. The timing belt is fine. The car has a rough idle and when I am stopped the RPM's drop below normal. Now it won't start. What can I try now?

View 1 Replies

Suspension - Mercedes-benz - S-class :: 1987 - Rough Idle And Stalls / RPMs Drop

Hot or cold car always starts,Idles perfect , then RPM drops, Idles rough and stalls. Econometer moves to Red area.car will easily restart and drives well,it also idles well. Once engine is shut down, even for a short while, It does the same thing again. Car is used for short trips. Ambient Temperature 80 degrees. Once running car is perfect at all speeds and idles smoothly. Hero 1987 MB 560 sel ....

View 19 Replies

Stalling - Ford - Focus :: Rough Idle / Shaking When Gets Under 1000 RPMs

I have a 2008 Ford Focus - 4 Door Sedan SE 60300 miles.

I've gone to 3 mechanics now and no one can seem to figure out whats wrong with my car. Here's whats happening:

About 1 1/2 years ago I took my car to get an oil change at Jiffy Lube (Yeah never again). When I left, my car was idling funny... Silly me didn't take it right back and have them tell me what was wrong.. so I let it go, well about a month later it started idling even weirder. Basically it feels like my car is shaking when it gets under 1000 RPM and I notice my RPM dial start falling and bouncing back, acting like its going to stall, but never does. I notice a loss of power when this is happening (on speed up and just accelerating in general). All of this is random, I can't seem to put a pattern to it as to when it happens. One day I'll start it up and everything is perfect... Then I'll shut it off and restart it later, and it starts vibrating and puttering again... No signals as to if its hot/cold or wet/dry, no environmental variables seem to cause it to happen anymore than others. And there is no check engine light on, everything "looks" normal.

What I've had done to it so far is:

Air filter changed / reseated
3 oil changes (keep getting told it will work)
Throttle cleaned
Computer reset for idle sensor data rebuilding

Now I'm told that I need new engine mounts, and that could be the reason for the vibration. I'm thinking that the vibration caused the mounts to wear out, more so than the mounts being the cause. Mainly because I don't see how bad mounts could cause loss in power/bad idling.

What could be wrong?!? Really bugging me and don't want to keep throwing money at it for phantom solutions. Seems like mechanics I go to can't figure it out unless there is a check engine light on with some diagnosis code to tell them exactly whats wrong.

View 8 Replies

Mazda - Tribute :: 2003 - Engine Idle Gets Really Low (like 500 RPM Or Less) And Sometime Stalls

When I am slowing to a stop, my engine idle gets really low (like 500rpm or less) and sometime stalls. At the same time, the oil light comes on. It does this all the time, and yes I've had my oil changed recently and actually I just checked it the other day and it was fine (along with all other fluids).

I've had the mechanic take a look at this three times and every time something gets fixed but this problem remains. They now say it's a ghost. It is not the air intake (I've had all of the hoses checked and a bad one replaced). It's not the electrical (I've had the spark plugs and cables replaced about a year and a half ago).

I've pretty much had everything that a car of a certain age needs done fixed/replaced in the past year or so, and I still can't figure out what could be causing this. A recent show had a similar problem, but the gal didn't mention the low idle/stalling. In that show they mentioned that she should have the oil pressure gauge checked or replaced, but would that cause the low idle/stalling? I don't know what to do and I'm very reluctant to go to a dealer.

View 19 Replies

Civic - Honda :: 1995 EX - Rough Idle / Stalling At Low RPMs And Won't Start When Humidity High

1995 Honda EX with 150,000 miles. Its been running rough ie rough idle, stalling at low rpms etc Additionally for awhile now when humidy reached north of 85% the car wont start. It cranks but rarely runs.

Took it to a mechanic last week for a tuneup. They replaced the Distributor cap, spark plug and wires and fuel filter. Car ran great for a day. Then progressively got worse. Was undriveable the other day stalling misfiring while at speed. Took it back today. They determined that it was still not getting spark and replaced the distributor. They did so, test drove it, declared it good and I came to pick it up. Paid the bill, walked out to the car and the damn thing would not start. Humidity was high.

Mechanic pulled a spark plug and put a tester in and didn't get a spark when cranking. He is assuming the distributor he just put in is bad. So they are keeping the car overnight to be fixed in the morning with a new distributor.

However I'm not convinced the dizzy is bad, I believe, as I've read that the Honda's ECU is probably bad and shorting out in the high humidity. Can a bad ECU would prevent spark?

View 2 Replies

Passat (B6) :: Rough Idle When Stopping For Light?

So far I have only experienced this once (today). I was on the freeway which ends and becomes a State Route. When I stopped for a traffic light the idle became rough. I put the car in neutral and gave it a little gas and it seemed fine. It has not done that again at this time. No CEL or anything came on. What do you think?

View 6 Replies

Mazda - Tribute :: 2002 V6 - Releasing Throttle Does Not Result In Engine Decelerating Or Returning To Idle

We've owned this 2002 Mazda Tribute v6 for six years. Recently, the car has become somewhat dangerous to drive. While driving down the road at any speed, releasing the throttle does not result in the engine decelerating or returning to idle. Instead, it continues to hold the speed steady for 3-5 seconds before the RPMs drop. At lower speeds (~5mph or so) the car will even accelerate a bit, which can be a problem in tight parking situations. At higher speeds (e.g. on the freeway) releasing the throttle has no effect for a few seconds (ie it does not decelerate), which can be very surprising if you're responding to suddenly slowing traffic. The brakes can, of course, overpower the engine, but you do have to push harder to get the same braking effect as if you were not fighting against the engine. Releasing the throttle and shifting into neutral while driving causes the engine to rev quite high (3,000rpm) for the same 3-5 seconds before dropping to a steady idle, but it does allow you to brake normally. Shifting back into Drive while in motion but not touching the throttle causes the engine to decelerate the car normally. Touch the gas even briefly, though, and the engine will once again surge.

Oh, and turning the steering wheel from side to side, as you might do while parking, also causes the engine to surge, though not as much as it does when I touch the gas pedal. Also, I've disconnected the throttle and cruise control cables and worked the throttle plate by hand. Doing so causes the RPM to rise, as you expect, but it does not immediately return to idle when the throttle plate snaps shut. Instead, the RPMs stay around 12~1500 for 3-5 seconds before it drops to idle.

Over the years, I've replaced the throttle position sensor, idle air control valve, and other normal maintenance items. I used a meter to troubleshoot the IAC and TPS and used propane to look for vacuum leaks, but everything is within spec. There are recall notices related to unintended acceleration for these vehicles, but those are reportedly caused by interference between the engine cover and cruise control. I do my own maintenance and don't like engine covers, so I removed the cover from this car shortly after buying it; the engine cover cannot be causing this problem. I have disconnected the battery for an hour to reset the computer, but that has no effect. There are no trouble codes that show up on a OBD-II scanner, and the CEL is not illuminated. There are many internet reports of this problem, but thus far I've found none that indicate a solution.

View 5 Replies

Mazda - Tribute :: O2 Sensors Causing Check Engine Light To Come On

I have a 2001 Mazda Tribute with 141,000 miles. Recently, I've burned up both O2 sensors causing the check engine light to come on. My mechanic has replaced each and they've burned out again. The head gasket was replaced after that, to no avail. The check engine light continues to come on after being cleared in the computer. I have also noticed that on humid days, the car misfires on at least one cylinder., but any other time, it seems fine. What to check next? My mechanic is at a loss.

View 2 Replies

Mazda - Tribute :: 2005 - ABS Warning Light Comes On When Reach 40mph

My 2005 Mazda Tribute has an ABS warning light that comes on as soon as I reach 40 mph. It will remain on after that no matter what speed I drive until I turn the car off. The braking system appears to function normally with normal breaking even if the light is on. With hard braking the ABS performs as it should too, rapidly oscillating the braking force. If I restart the car and keep the driving speed below 40 mph the ABS light never comes on. Otherwise, the car runs great. What is causing the ABS light to come on at 40 mph and how do I fix it?

View 2 Replies

Mazda - Tribute :: Car Starts But Have To Rev The Engine And Restart At Every Stop Sign And Red Light

My Mazda tribute 2003 (manual) has developed a habit of 'pretending' to be overheated. If I do more than 2 or 3 stops as I run Saturday errands on a warm day - the care refuses to start and' continue' to run. I can start the car but have to rev the engine and restart at every stop sign and red light- If I pop the hood and wait about 40 minutes the car seems to 'cool' down and will run. The engine does not redline - water and coolant are fine - Is this just a faulty thermostat or is it some insidious vapor lock....

View 3 Replies

Mazda :: 2002 MPV Stalling After RPMs Go Over 2000 And Let Off The Gas

My 2002 Mazda MPV will stall everytime after the rpms go over 2,000 and I let off the gas. I can put it in neutral and it will start back up. Not sure if something is clogged or its electrical? It has 177,000

View 6 Replies

Chrysler - Towncountry :: 2008 - Stalling Out / RPMs Will Drop To Zero And Gas Pedal Is Loose

I have a very specific problem with my 2008 Chrysler Town and Country. It has happened 4 times in the past few months and the dealership is unable to replicate the problem, so they tell me there is no problem. When I am decelerating/coasting the traction control light on the dash will come on, the power steering will go out, the RPMs will drop to zero and the gas pedal is loose and has no effect, and then the power brakes will go out. All the electrical still works, I muscle over to the side of the road, turn it off, wait a few seconds, turn it back on, it starts up just fine and I drive off with no problem.

The first three times it happened I was on the same stretch of road (which I dubbed the Bermuda Triangle Road), I was going 25 mph, the road is fairly level, the pavement was dry and it was above freezing. The fourth time was on a different road, but still level, there was snow and it was below freezing but the road was clear, and I was going about 33 mph. Each time the car had been sitting in my garage for at least a couple of hours, and it happened only a few minutes after leaving the house.

View 4 Replies