Camry :: Rough Idle - Vibration Start As Soon As RPMs Drop A Little
I've made posts about a rough idle before now I noticed something new about it. I noticed when I approach a red light the vibrations don't start immediately. They start as soon as the RPMS would drop a little. They stay above 500 but it seems like it's below 750. As if the engine is slightly starved from power? Now i'm wondering if it could be related to another problem I have.
Whenever I start the car, the battery light flickers until the car is started all the way. This is on a 2007 Camry 4 cylinder. So far everything iv'e done is: New NGK Spark Plugs, NEW OEM mounts (all 4) Seafoamed the engine, Seafoamed the throttle body, cleaned the MAF sensor, New air filter, and cleaned the air filter box, replaced the PCV Vlave, new belt, new alternator (duralast), and a new battery (from autozone).
Integra :: 1987 Rough Idle / When Stopped RPMs Drop Below Normal
I have done everything I can think of to this car. New; plugs, wires, distributor, battery, fuel pump, fuel filter, relay, and electrical lines to fuel pump. The timing belt is fine. The car has a rough idle and when I am stopped the RPM's drop below normal. Now it won't start. What can I try now?
View 1 RepliesSuspension - Mercedes-benz - S-class :: 1987 - Rough Idle And Stalls / RPMs Drop
Hot or cold car always starts,Idles perfect , then RPM drops, Idles rough and stalls. Econometer moves to Red area.car will easily restart and drives well,it also idles well. Once engine is shut down, even for a short while, It does the same thing again. Car is used for short trips. Ambient Temperature 80 degrees. Once running car is perfect at all speeds and idles smoothly. Hero 1987 MB 560 sel ....
View 19 RepliesMazda - Tribute :: Rough Idle When Cold / RPMs Drop Close To Stalling When Stopping At A Light
I have a 2001 Mazda Tribute with 150,000 miles that is meticulously maintained. This past winter (as far as winter goes in San Diego) the engine would run rough and the rpm's would drop close to stalling when stopping at a light for the first 2 or 3 miles. After that the engine has warmed and there is no problem. Could this be the intake gaskets needing replacement. This only happens on a cool or damp, rainly morning.
View 6 RepliesFord :: 1997 - Engine Disengages RPMs Drop Below Idle
Twice now this has happened to me and I'm concerned it will become worse if I don't fix it. Driving down the road my engine has disengaged. By this I mean the vehicle both times has been at 55 MPH, my foot on the throttle rpms riding around 1300 revolutions, and the engine disengages rpms drop below idle and my "wait to start" light comes on. This both times lasts approximately 2 seconds and throttle reengages while still traveling 55 MPH, "wait to start" light goes off and its like it never happened. What's going on with my truck? Ford diesel 97 250 7.3 ...
View 2 RepliesDodge - Dakota :: 2000 - Engine Starts But Won't Idle / Just Dies And RPMs Drop
Cold start. engine starts but wont idle, just dies. rpms drop. Restart same. Must neutral drop to get going keep rpms up until engines shifts then things are fine until next cold start. Cleaned throttle, changed air filter, dry gas, injector cleaner, no warning signal, scans clean. 180k miles.
View 6 Replies1992 S10 Blazer - Rough Idle At Start / Shuts Off In Gear And Engine Never Getting Higher Than 180
1992 S10 Blazer, 4.3L, 4x4, TBI "Z"
When I start the truck, it idles rough, like it's idling too low, and even feels like it's missing during idle. Sometimes when I put it in gear (reverse or drive), it shuts off. No codes are being thrown. It has no problems driving around town or on the highway. It's just that initial start and idle.
I've checked all the following with a shop manual:
Ignition Control Mod.- Orig and 2nd one from junk yard. Both tested good at store. Even the testing in the shop manual with an ohm meter and battery tested good.
Ignition coil- tested good using shop manual testing
TPS- Scan shows .2-.7 at idle.
Plugs, wires, cap, and rotor are good.
Vacuum is good.
Haven't checked IAC, EGR
I recently moved cross country, and about halfway through, I broke down. Engine would turn over, fuel relay would click, injectors would work, but no fuel. Pulled it in to a truck shop, and after all my testing and theirs, we determined it was the fuel pump. After they had to fix a pinched hose, it ran. I made it to Texas. I didn't have the idle issues prior to the trip. Just had the tranny rebuilt and everything was great.
I thought, at first, the ignition control mod was the problem because it got a bit warm pulling the trailer, and I know those things don't like too much heat. No dice. So, what controls idle at Park and in gear but at idle? EGR, IAC?
I did a WinALDL scan. IAC at Park/Idle ranges from 18-55. The engine never runs in Open Loop. I would say the engine runs mostly rich according to the scan. I've attached a manageable version of the WinALDL data.
Also, I need to check the thermostat or temp sensor. Scan reads the engine never getting higher than 180.
Santa FE SM (2001-06) :: Hard To Start After Fill Up - Rough Idle And Engine Shuts Off
Every time i stop for gas..my 01 santa fe is hard to start..it would take 4 to 5 start before she goes, then i have to keep the rpm up, bring her to idle..after that shes ok, till the next fill up.. the only way around this is to keep her running while gassing up..while filling up she run rough idle, some time engine shuts off..then its hard to start..
View 5 RepliesFord F-150 - 1997-2003 :: Rough Idle / Engine RPMs Go Up To 2k Before Dropping Down
1999 F250 LD with 5.4 w/ 225k miles... Was running perfect yesterday when I shut the engine off. Started back up about 20 minutes later and Idles was up and down and rough.( 400 - 900 rpms) Drove and ran fine except Idle. I know that those codes are for the o2 sensors but don't believe they're bad. I hear what sounds like a vacuum leak somewhere behind throttle body. Either IAC or EGR or it could be coming from the line that runs in beside the IAC valve to the air intake in front of the throttle body. Tried spraying water in those areas with no results. Could it be a bad EGR valve or a stuck IAC valve? I have also noticed that lately when I start the engine the engine rpms go up to 2k before dropping down. Would a bad IAC valve cause such rough idling along with the codes that I described?
View 7 RepliesSubaru - B9-tribeca :: 2006 - Car Rough Idle / Engine Shaking For Few Seconds
I have Subaru B9 Tribeca 2006. Week ago started the following problems - after starting up, engine is shaking (rough idle) for a few (20-30) seconds and then it's OK. Then I got Check Engine, Cruise and ABS lights on. Diagnose shows mistake in 1st cylinder. changed spark plug, air filter, checked all connections, cleaned injector and throttle. Lights went out and engine was working as new. but the second day car had rough idle again....
View 1 RepliesGolf V R32 :: Car Shuts Off - When Restart RPMs Bouncing At Idle
I got a mkv R32 with 57k miles (DSG transmission) on it and the past few weeks ive been having some crazy issues. My car shuts off once in awhile when I come to a stop in traffic or at red lights. Last night it happen again I came to a red light and the car shut off, when I restarted it my idle was bouncing all over the place all the way up to 2500rpm and down to 1300rpm. Also, in addition to the idle every time i started pressing the gas the car would KICK like something was wrong with the transmission and a CEL came on. I ran the codes and it said MAF was at fault and I have had a MAF code again maybe a month ago.
I am thinking of replacing the MAF to see if it fixes the problem and I was wondering if it is a straight hardware swap or will i need to do some programming with a vag com?
Passat (B5) :: Idle Sputter / RPMs Will Drop Then Will Eventually Stabilize
As listed above I own a 98 Volkswagen Passat. It seems to run just fine for the most part, but if I push on the gas and let off I notice a slight sputter. The RPM's will drop to about 800RPM up to 1000RPM and back down again and it will eventually stabilize and idle fine. My only guess that I have so far that I read on a post somewhere is that the EGR Valve tends to get gunked up and stick. I will try to clean that off.
View 12 RepliesDodge - Dakota :: 1996 SLT Idles Rough / RPMs Will Drop To Near 0 Within About 20 Seconds Of Coming To A Stop
So I have a 96 Dodge Dakota SLT 3.9 4WD. Anyway, it idles relatively smoothly at about 700 RPM in drive or neutral, but if I'm in a moving gear and need to stop, the idle is extremely rough. Usually, the RPM's will drop to near 0 within about 20 seconds of coming to a stop. It will typically recover and continue with rough idling and near stalling a few times, but within a minute or two it stalls. A few additional details: it starts right up again after falling, it doesn't make any difference if I start it cold and drive immediately or drive it for an hour before coming to a stop, the same thing happens. Anything that looked suspicious to me has been changed (drive belt, spark plugs & wires, distributor cap & rotor, pcv valve, idle air control valve, and, of course, the air freshener).
View 1 RepliesFord F-150 (2009-2014) :: Ticking Noise At 800 To 1000 RPMs / Rough Idle Leads To Engine Fail
2010 F150 ... So I have the tick noise at rpm's 800-1000 at drive through, stops, etc. So I did research on it a few months ago and saw that it might be VCT's but should be able to drive. so I drove it waiting to save money and have it go to a shop. well this past weekend while coming home from work my oil light came on the pressure dropped to zero, I was on the highway so I drove about another mile to get off highway and once I got off my truck died. I had it towed to my house and I thought I blew my motor. So I started doing research here and found that the VCT's AND cam Phaser could be bad. so I replaced my VCT on driver side put it all back together it started and loud knock was gone. then after 5 mins it was back very loud knock!
So I shut it down and took apart the passenger side once I got the valve cover off I found the problem.... The bolt that holds the cam phaser in place snapped off and was riding along the camshaft. So I took that out and extracted remaining part of bolt. inspected my camshaft and it was really messed up. so I bought new Phaser and Camshaft. the camshaft just came in today and I am trying to put it back in. but the hole for the pin in the phaser doesn't line up and I cant spin the shaft to make it line up. should I spin the cam phaser? I marked the chain and the phaser is where it should be on chain, but with that bolt snapping off could that have thrown the timing off so my mark is no good? when I lay the camshaft in place it sits perfect and if I just move the phase over 2-3 links it will all fit together. Should I do that?
Subaru - Outback :: 2000 - Fast Idle On Start And Severe MPG Drop
I have a 2000 Subaru Legacy Outback with 208,000 miles. Last Oct I had a complete tune up done on it: fluids, filters, spark plugs, etc. Ever since then, the gas mileage has dropped from getting around 390-400 miles off a full tank to 290-300 miles off a full tank. I have tried carburetor and fuel injector cleaners and nothing is working. At this same time, it also started idling at 1750 rpms every time I start it, dropping down to around 750-900 rpms after I put it in gear. The timing system was replaced about 7 months earlier. So far the repair shops can't find anything wrong. I also just had the transmission rebuilt and it's still idling fast.
View 4 RepliesGolf IV / Jetta IV :: Revs Just Drop Down To 0 And Engine Shuts Down While Slowing Down
Looking for some hint regarding V6 AUE ? Regardless if engine is warm or cold, sometimes happens to me that during driving, while slowing down and pressing on clutch pedal, revs just drop down to 0 and engine shuts down (vehicle still moving). This usually happens while changing gears from 3rd to 2nd on low speeds in city, or while slowing down to full stop in 2nd gear and pressing clutch pedal.
While this happens, I quickly switch off the ignition and start the engine again, which is tricky and potentially dangerous, since vehicle is still moving but my power steering and brakes are not functioning because of stopped engine.
Some relevant info...I have K&N cone air filter intake and ECU is remapped by BTS Racing (German tuning house).
Car is running and pulling normally. In all other regimes of driving, there are no issues or whatsoever.
Ford 7.3L Power Stroke (1999-2003) :: After Start Up RPMs Drop - Stalls Out Then Idles Rough?
2003 7.3 excursion.. The truck starts every time revs up and idles about 3 seconds then the rpms drop and it tries to stall out catches itself then revs backup and idles rough similar to if you have got air in the fuel lines from changing the fuel filter.. About 1 in five times the truck will stall out and it starts and immediately and idles rough but the rpms and everything runs at speed and rpms don't drop again! This is a reman engine/transmission recently installed.. The mechanic who installed it was unable to figure the problem out.
View 6 RepliesAudi A4 :: 1997 Stalling - When Started Up And Left To Idle All Of A Sudden RPMs Drop
I have a 1997 Audi A4 that has been acting a little bit strange lately. When it is started up and left to idle all of a sudden the RPMs drop from around 600-800 to 100-200 sometimes rebounding back up and sometimes the car just dies. This also is happening while I am driving and stopped at a stop light for a short time. It will idle fine then suddenly drop RPMs and if I don't give it any gas then the car usually dies. I have just had some work done on it to try and fix this problem thinking it was the air flow sensor (or something like that) but apparently that is not the case.
View 2 RepliesGolf/GTI VII :: Rough Idle And Shuts Down Sometimes
Symptoms:
- rough start-up, car shuts down
- backfire when releasing after WOT
- OBD-II codes (see below)
Okay so these issues started to appear only 1 day after I got tuned...
Problem History:
Day 1:
- car started mildly rough
- I got an EPC light on my dash 2 minutes after moving and for 2 seconds the car sounded like an STI (the sound you hear with a misfire)
- I turned it off and on, EPC gone car started up normally
- took it straight to dealer, they checked coils and plugs and said that it's a tune issue.
- went to take it back from the dealer and that was the first time the car shutdown immediately after start-up. it started at second attempt with a quite long ignition sound and the STI-like sound briefly once again.
Day 2:
- I went to my friend and we pulled the codes from OBD-II and only got the P0420 00 [175] - Efficiency Below Threshold code only (as the dealer probably erased any other code related to my EPC light)
- we deleted the code and drove around
- every time we turn the car off and on. The car starts up mildly rough and the code comes back up
Every 2 days or so:
- the car would require 2 attempts to start but no EPC light coming up.
Day 4:
- I had a night of possibly 6 WOTs to test the cars performance, and it was performing great. didn't feel any loss in power or anything. (was friendly racing my friends modded 135i with very impressive outcomes)
- car backfires after i release the gas pedal at WOT (not with every WOT but 2 out of 6 runs it backfired)
- After the last WOT i got the EPC light. turned the car off and let her relax for 5 minutes.
- car took 2 attempts to startup. with severe roughness and shakes (as if the car is cammed V8 engine) for 5 seconds and then back to normal.
Now since the EPC light came back on i wanted to check if there is another code from the OBD-II. I was hoping that the issue will only be the P0420 00 [175] - Efficiency Below Threshold code but my fears were true and i got another very annoying code
This is last nights code pull
2 Faults Found:
14914 - Boost Pressure Regulation
P0299 00 [096] - Control Range Not Reached
Intermittent - Not Confirmed - Tested Since Memory Clear
[Code] .....
Day 7:
- The car had the sever start-up roughness again
As I'm trying to find a solution for my problem here are the steps i took/will take:
- took it to the dealer for nothing.
- ordered an O2 sensor extender for the P0420 00 [175] - Efficiency Below Threshold code and i hope it's somewhat related to the start-up issue. it will arrive today or tomorrow.
- once the extender is here, I'll take it to an exhaust shop to install the extender and check for any DP/Exhaust leaks
- I will take it to a mechanic to check any leaks in all intake/air connectors and piping, any leaks in DV (I have forge recirculating DV), Boost pressure sensors (the piggy back was connected to them and one might be loose when we removed it), spark plugs and coils.