Lexus RX 2010-15 :: How To Change Light Bulb On License Plate
How to change the license plate light bulb for lexus rx 350 2010.
View 4 RepliesLexus IS 2014+ :: License Plate Rattle On Closing Trunk
Notice a rattle when they close their trunk?
My top screws are plenty tight, but the bottom portion seems to not be secure enough since they do not have screws.
Lexus IS 2014+ :: Trunk License Plate LED Bulbs Replacement
I tried doing a search on how to replace the License plate LED bulbs...
Looking for pictures or instructions on how to replace them...
Lexus IS 2014+ :: Rear License Plate Mount Rusting Already?
My Ultra white IS350 is 15 months old, and when I took out the screws to my license plate today, I noticed a little bit of rust on the mounts (where the screws would go into).
I believe this is a pretty common issue for all cars - essentially, the mount was sprayed with body paint, but the paint would be stripped when you put a screw in. It's just a matter of time before that happens.
I am just concerned it would rust through my trunk if I continue to leave it.
FYI: I already use stainless steel screws
Golf/GTI VI :: License Plate Bulb Out Error With Stock Bulbs?
I have an intermittent error that comes on most of the time I have my headlights on, but sometimes goes off and comes back while I am driving. It shows me the bulb out light, and says on the screen "Number plate Check license plate lighting!" I have never touched the oem factory bulbs on the license plates, and if i get out and look at the plate, both lights are on over the plate.
The only change I have made was about a year ago, I installed an LED bulb in the trunk, and ran a second OEM trunk light in the left side and installed an LED bulb in that too, tee'd off the factory trunk light housing. But like I said, that was 1 year and 30,000 miles ago, and my bulb our error for the license plate has only just started, so I doubt they are related.
Lexus RX 2010-15 :: 350 Front License Plate Holder?
After going through the car wash several times now in my 2010 RX 350, my front license plate has been bent in all different directions. Car wash guys say it's due to not having a full plate holder, where as 4 screws secure the plate vs. only the top 2 as we have. Any plate holder from another vehicle that I might adapt to overcome this?
View 14 RepliesCamry :: 2002 - Remove And Replace Burnt License Plate Bulb
02 Camry, how to I remove the burnt license plate bulb? Took off the underside trunk carpet and disconnected bulb harness, but I don't know how to remove the plastic piece that holds the bulb in place. Does it pull out, or twist out? I don't want to break it!
View 1 RepliesLexus RX 2010-15 :: How To Change License Plate Bulbs To LEDs
I wanted to change my license plate bulbs to LED's. Can't figure out how to get to them. The book says have the dealer replace these bulbs if burnt out. I Always like to try to do things myself.
View 7 RepliesLexus RX 2010-15 :: 450h / Front License Plate Frame?
I have a 2010 RX450h and live in Minnesota where it is hard to hand wash my car. The darn car washes tend to catch the front of my license plate frame and bend it and the license. I have tried several different plate frames and none worked. Minnesota plates are now the thin, non-stamped plates so they are very flimsy.
I even tried putting a plastic plate behind the license to make it more rigid but that failed too.
Lexus RX 2010-15 :: Removing Rear License Plate Trim On 2015 Fsport?
how the chrome trim above the rear license plate is removed?
View 4 RepliesLexus RX 2010-15 :: How To Replace Bulb On RX350 Headlight
How to change out 2015 RX350 headlight bulb? How to replace the bulb on the 2015 RX?
View 12 RepliesElantra MD (2010-15) :: License Plate Lights Keep Burning Out?
For a few weeks now I noticed my stock license plate bulbs started to act strange. My left one is about half burned out, and the right one started to flicker and burned out entirely.
So.. Easy fix right? I bought 4-smd led lights to replace the burnt out ones and as soon as I installed them they worked perfectly! But about twenty minutes later .. The right one burned out. And the left one is dim.
Is there something wrong with the wire? what can I do?
Lexus ES 2007-12 :: How To Change License Plate Bulbs
How do I change my license plate bulbs in a 2010 ES350? I bought some 194 JDM Astar LEDs. I took off liner and changed backup bulbs but can't figure out how to change license plate bulbs.
View 4 RepliesLexus GX 2004-09 :: Can't Get License Plate Light To Stay In
I'm in the process of replacing license plate bulbs. I broke the old housing for one of the bulbs so I bought new LED lights on eBay and they came with the housing. The problem is, I can't get the cover to stay clipped in to the tailgate. How to get the lights to stay in? What am I doing wrong?
View 7 RepliesLexus ES 2007-12 :: How To Replace License Plate Bulbs
I'm trying to change my license plate bulbs to LED but cant figure out how get to the bulb. I've already removed the carpeted cover but cant seem to figure out how to get the bulb out..... 2007 ES350....
View 3 RepliesLexus SC430 :: 2002 - From Where License Plate Lights Get Power
Where the license plate lights get thir power from? I have a 2002 SC430 and the plug is just dangling. It goes behind the plate and then if I look under the car, it is just there by the bumper and I cannot find a connector that it can reach.
View 3 RepliesLexus GX 2004-09 :: Cannot Find Fuse For License Plate Lights
I try to install LEDS on it and I guess I accidently blew the fuse and when I try to search for it, I can't locate it.
View 3 RepliesLexus ES 2013+ :: Front License Plate Relocation On 2016 350?
yesterday I got the idea to move the plate bracket on the front all the way down so it gives it a much cleaner look and doesn't obstruct the grille. To do so test mount the bracket on the lowest position, then have someone hold it. Then you take a 1/8 drill bit and make the two new wholes then put everything back together.
View 8 RepliesLexus GX 2004-09 :: Front License Plate Mounting Holes?
I need to mount a plate on front bumper and there are dimples for 2 holes. Do I just use self tapping screws here as I've read you don't need a mounting frame?
View 3 Replies